Low performance w/M4 on P67A-UD7

Trackr

[H]ard|Gawd
Joined
Feb 10, 2011
Messages
1,786
So, on my P8P67-M Pro, performance was phenomenal.

I move the drive to my P67A-UD7, and Windows takes twice as long to load.

So, I checked whether I was using SATA3 and I am because I get 500MB/s read.

And I set it to ACHI.. but it's still much slower.

P8P67-M Pro
92167666.png


P67A-UD7
46998471.png


So, what's up?
 
did you let the drive fill up to within a couple % of its capacity in the first pic? the reading speeds are not that much to worry about, different controller on the motherboard and such, but the write speeds, well that is a huge difference. I would maybe use CCleaner and do a cleaning of extra junk, let the drive run for a couple of days as normal to gain its TRIM and BGG cleaning effect, then run again, if still same problem, might have to secure erase the drive so its more or less back to stock performance.

If its an M4, have you the newest Firmware on it?
 
This is happening on two separate M4 drives. Same issue.

The odd things is - the Write performance is down, right? Well, then why is the only thing that is noticeably slower Windows boot-up? Isn't that supposed to rely on Read?

I'm starting to think that maybe the problem is the BIOS..? Versus EFI on the ASUS.
 
Could very well be, they do use different controllers for the SATA and such as well,I believe ASUS uses an ACETEK unit(one made by them) Gigabyte maybe uses a marvel, Jmicron, or even possibly a realtek derived one.

I know at least for the AMD 900 series motherboards the ASUS 970/990x/990FX tend to have more defined stable performance in regards to PCI-E, SATA, and usb, it might be the controllers, or it could be the bios control chip being used, ASUS UEFI approach is so much nicer in regards to what you see is what you get. At least the intial reviews said, it worked just as it was supposed to with no hitching and such.

So, if the UEFI approach has some lingering issues or lack thereof, seeing as the bios does control, well pretty much everything, that very well could be part of the issue, however, the actual controllers or added chips providing the functions can also be culprits.

Now you said you are not running in AHCI, and if you are is it via microsofts AHCI version or the chipsets AHCI? I know going by what Corsair is saying on their Firmware update page, AHCI is very important, it allows the SSD to run the way it was intended and any added functions based on such to work as they should. They also recomend trying the SSD with the chipsets AHCI and if performance is not where it should be try using microsofts AHCI approach.

During bootup as in going from bios to pre-load of windows, to windows, it might be the sata controller is "switching" and there is something not right with it, so its "hitching" which could very well be the AHCI not reacting the way it should, I would try both AHCI approaches, see if that makes a difference. and, not to be a party pooper, but do not bench the SSD to many times, its hard on it :)

this shows how to do it for the default microsoft based AHCI, am sure if you choose the actual chip set based AHCI instead it would work more or less in the same concept
http://forums.guru3d.com/showthread.php?t=313676
 
Actually, it's probably because the ICH10R controller that comes with the Z68 chipset has some SATA 6.0G/bs performance improvements according to the Intel rep here on the forums:
There are really 3 differences between the P67 and Z68 chipsets.

Z68:
-Intel SRT (Smart Response Technology) SSD caching. You can use up to a 64GB SSD.
-Support for IGP (Intergraded Graphics on Processor). There are a couple things that play off from this including the Lucidlogix Virtu software and the ability to overclock the IGP (about half of Gigabyte’s Z68 boards don’t support this feature.
-Intel SATA III controller (better performance)

At least as far as the chipset goes there is around a $6 dollar cost difference.

With that said, did you do a fresh install of Windows 7?
 
SRT is its own thing, isnt that meant to be used with a standard HDD that allows the SSD linked to it to speed its performance(vs using the HDD as a stand alone unit?) if so, and to my knowledge it is, then most "performance" SSD by itself should get better performance.

A fresh install, and a secure erase of the SSD might very well help alot, but then again, if the drive is being used on a controller that does not allow it to be used to its full benefit(sata 2 or a sata 3 not running at its "spec" performance) that can account for the major difference between the 2 different boards, being a possibly first gen Jmicron/marvell sata 6 controller vs a 3rd sata 6 controller on the current offerings.

The secure erase/refresh of the cells in the SSD can help drastically, but only if the chip doing the communications to it is running at its optimum. Now, I may be wrong in this, but ASUS with the majority of thier boards do seem to get better SATA speeds as does intel vs most other boards using add in chips from other vendors?
 
I tried both AHCI approaches, and nothing.

Also, I'm not sure what Z68 has to do with this, as both motherboards are P67.

All in all, this makes me want to buy ASUS next time around.
 
well, I know this will sound assinine(or however its spelt :p) but it may be very benefical to check on the specs of the board before you get it. I know with ASUS and the baord I am using M5A99X EVO, the M5A97 EVO and non evo do not get as much performance from SATA and such, and the baords above it being the sabertooth and Crosshair get better performance.

It pays to do alot of research first. Ther is a reason why ASUS is number 1 overall, very well know name, very good products from top to bottom of range. ASUS, EVGA, Sapphire, DFI in that order in my opinion. I know alot of folks recomend different products based on opinion or purely on a performance from cpu standpoint, but stability and component performance plays a massive role in the experience, after all, you could have a cpu 10k times faster then we have right now, and if the hard drives or memory is holding it back, what good is it?

I have a feeling then its probably the controller, did you try putting it onto a different SATA input? might be different controllers for the different inputs or for that matter different drivers available to it?
 
I don't have a SATA 3 PCIe card.

ok, but did you try it on a different sata slot it can make a difference if the chip controlling that slot is not running its full potential.

however, most SATA II SSD seem to be 250/220 read/write or thereabouts, a SATA 6 SSD used on a SATA II slot will not run to its full potential, in alot of cases, only getting 1/2 or so of its quoted speeds :(
 
Yeah, of course I tried more than one SATA port. That's basic.

On the first two, it would get to about 400MB/s (SATA3).

On the second two, it would get to 500MB/s (running right now).

And the last four are SATA2 ports.. I get about 250MB/s max on them.
 
Yeah, of course I tried more than one SATA port. That's basic.

On the first two, it would get to about 400MB/s (SATA3).

On the second two, it would get to 500MB/s (running right now).

And the last four are SATA2 ports.. I get about 250MB/s max on them.

Let me guess...

The first two ports are Marvell-powered while the second two are Intel-powered.
 
seems like it may be the case, now you said first 2 would get about 400mb/s(SATA 3)

SATA 3 is otherwise known as sata 6GB/s, though you said previously, you do not have a sata 3 pci-e card, im confused now :p

500mb/s is around the speed you should get, but if its running in SATA 2 speeds, the writing side of it will suffer. The specs coming from Crucial themselves for Part Number: CT128M4SSD2 are up to 415-500mb/s read(SATA 6GB/s) up to 175mb/s write(SATA 6GB/s) 4k random read up to 45,000 IOPS 4k random write up to 35,000 IOPS. The 500 comes from newest firmware I believe.

So, if you are infact running it via a SATA 2 and not a SATA 3 otherwise known as SATA 6GB/s then you are getting close to the speeds it should be getting, the drivers for the sata controller, the drivers for AHCI, even the firmware on the SSD itself can impact this.

Now I am obviously not sure of your actual bootup/down speeds, but there are things that can help get the most out of it, not sure in your case how much it will help as the drive "shouldn`t" see its full speed via SATA II or sata 3gb/s if you look at it that way, however, if you say press the power button, and the system is fully booted into windows ready to go in under a minute, well then its fast, the ASUS board may have been faster, but that may be the difference of SATA controllers etc, or, the difference of the drive being new whereas now its not new, and if it hasnt been secure erased to bring the cells performance back to ground zero it may not be helping.

Take a stop watch out, and time it from power to fully booted?

Kind of funny though, the marvell ports should work as well considering its a marvell controller on the SSD as well :p

As far as windows boot-up being slower, well it does use a paging file, which it does write to, unless you have turned that off, in which case it may be relying on your mechanical drive or something.

Needless to say, I have run out of ideas unless you want me to do a complete list of turn off/turn on type stuff, and general optimizations, though I doubt it would help much, its more meant for keeping the performance stable sort of speak. I would look for new firmware and SATA drivers, and do use them on the Intel sata ports they tend to have the best performance of all sata controllers even now.
 
what are overclock settings for first and what for second picture? Do try to put everything on stock and disable all 3rd party gadgets onboard as marvell controller, usb3, whatever so that doesn't interfere.

it looks to me that you have driver issues. Is it fresh windows install? Do you use same drivers? try beta and official RST.

I'd suggest checking write caching is on, but 4k write is way too high for that to be turned off. This is very puzzling.
 
I have noticed 0 difference with my single drive with write cache on or off, SSD I doubt will make overall much useage of this from a performance standpoint. now, if the drive was say formatted for use as a 512b or 4096 or 4k that can make a big difference in performance, that is a very valid point. I believe by default windows 7 is designed to use sata 6 drives in 4k sector format for best performance, and the nand type used may benefit alot from it.

RST is intels rapid storage tech, now I may be wrong, but isnt RST mainly for raid use not AHCI or IDE? Now this is a good point, most SSD do not use native TRIM/BGC in a raid format, they need to be in AHCI to benefit from most of thier advanced features, it may not "help" performance, but it most certainly should stop it from getting worse, and may help bring it back over time.

Ok, now as far as those boards are concerned
ASUS
Intel® P67 Express Chipset
4 xSATA 3.0 Gb/s ports
Intel Rapid Storage Technology Support RAID 0,1,5,10
(blue)
2 xSATA 6.0 Gb/s ports (gray)

Marvell® PCIe SATA 6Gb/s controller
1 xExternal SATA 6.0 Gb/s port
1 xSATA 6.0 Gb/s port (navy blue)

Gigabyte
Chipset:
1.2 x SATA 6Gb/s connectors (SATA3_0, SATA3_1) supporting up to 2 SATA 6Gb/s devices
2.4 x SATA 3Gb/s connectors (SATA2_2~SATA2_5) supporting up to 4 SATA 3Gb/s devices
3.Support for SATA RAID 0, RAID 1, RAID 5, and RAID 10
* When a RAID set is built across the SATA 6Gb/s and SATA 3Gb/s channels, the system performance of the RAID set may vary depending on the devices being connected.
2 x Marvell 88SE9128 chips: 1.2 x SATA 6Gb/s connectors (GSATA3_6, GSATA3_7) supporting up to 2 SATA 6Gb/s devices
2.2 x eSATA 6Gb/s connectors (eSATA/USB Combo) on the back panel supporting up to 2 SATA 6Gb/s devices
3.Support for SATA RAID 0 and RAID 1

So, yes it does in fact support SATA 6 on both those boards, but, if the drive has not been reset to default speeds(secure erase to refresh the cells) if they are not using thier newest drivers, if not in AHCI and so on, it may be why they are not getting thier proper speeds.
http://ca.asus.com/en/Motherboards/Intel_Socket_1155/P8P67M_PRO/#specifications
http://www.gigabyte.com/products/product-page.aspx?pid=3646#sp

Check to make sure you have the nwest AHCI, sata and such drivers if you have not already, that they are being used on thier proper ports, and for that matter like Ivan stated, turn the stuff off that WILL NOT help SSD do thier thing. Write cache I believe doesnt matter either way. superfetch/prefetch as well may hinder performance, AHCI as well make sure is on, compression off, indexing off at least for the SSD

I know this sounds messed, but alot of SSD have a pretty smart controller built into them, as does windows, it may take a bit of time for the drive/OS to get somewhat accustomed to what is reuqired of them, not to mention for TRIM/BGC to do its job, if X cells are being tapped it can lower performance big time.

SSD truly only have thier performance if their cells are not being smacked around, having crap being moved on them constantly(defragging, benchmarking and such) or when the drive is not properly formatted for a new build can play havok on thier performance and can lead to some pretty large disparity of quoted and given performance.

170mb/s in a "dirty" state with the 256gb version of the M4 which is ALOT faster then the 120gb version
http://www./forum/hardware-canucks-reviews/45718-crucial-m4-256gb-ssd-review-12.html
 
Okay, well..

I tried to disable everything and I did both tests at stock, but I need USB 3.0 to function for my mouse/keyboard.

In regards to drivers, well, I don't think that that is the issue because on the ASUS, after a fresh install, it's fast out of the box, no extra drivers needed.

I also don't know where to find the latest AHCI/SATA drivers. I've looked..
 
? mouse keyboard should work 100% fine on usb 2, they are back compatible, I have not heard of it HAS to be usb 3 for these. So I am not sure what this means.

Fresh install on ASUS means, unless you did a clean format on that drive and reset the cells as I have said a few times, they will not be operating at thier "peak" performance.

this page and its various drop boxes will show you the actual drivers for your motherboard, youll want the ones under SATA RAID heading. Also FORCE to use AHCI through windows, go back to bios to enable it, then install the motherboards AHCI over that.

http://www.gigabyte.com/products/product-page.aspx?pid=3646#driver

Now if you did not know how to do a SSD firmware update or whatever
http://www.crucial.com/support/firmware.aspx just do be sure to choose the appropriate Firmware, make sure to use the right one based on your actual model, and 100% verify the actual firmware version. This can help alot of can be issues that cannot be solved otherwise.

Also I highly advice reading this thread
http://forum.crucial.com/t5/Solid-State-Drives-SSD/M4-Secure-Erase/td-p/53826
It may clear up some issues and questions behind garbage collection, trim and such. For me, I logoff every couple of days, I use CCleaner to get rid of extra stuff that collects for nothing, old files and such. But generally speaking, if the SSD is in use, the TRIM and such will not kick in very often, so it will not keep the drive where it should be, constantly using the drive with fill the cells up, and they lose performance. Hitting the logoff button and preventing the system from hibernating or sleeping will allow the drive to TRIM and garbage collect like it should, and may help it get faster, if not, at least help it from getting slower.

To force AHCI to start the process, to allow you to select default drivers, then you can patch over it with ones meant for your board
http://www.sevenforums.com/hardware-devices/17876-enable-ahci-windows-7-a.html
As well double check TRIM is enabled
http://forums.legitreviews.com/about23670.html

You may also be able to get Intel AHCI drivers directly from thier site, or even INF files from them as well, but you need to know 100% the actual chipset # that your board uses(this you can verify on the homepage for your motherboard model and revision number)
 
Last edited:
I got all the SATA drivers from the Gigabyte site, but the Intel SATA Preinstall driver isn't useful. There is no .exe, so I had to go into Device Manager, but none of the items that need drivers were able to use the Preinstall drivers.. so it's moot.

I will update the SSD firmware, but not right now.

I forced AHCI, that didn't work.

I checked and TRIM is working.

I do appreciate the help, but I think there's nothing else I can do..
 
you tried all 4 of the available drivers for it such as the rapid sotrage thingy or the marvel drivers? What about the INF utility?

I know there was a way to force it to look at what you point it to look at, as in right clicking on the drive in question, properties, hardware, drivers and then pointing it to the downloaded location or something?

Not sure what else I can do to help, maybe send Gigabyte or Intel an email and ask them, they may be able to direct you better, or they may say all the above, hopefully they can help more directly :) after all the UD7 based boards are not cheap, I know Gigabyte can be anything but helpfull, nothing you can do but try after all.
 
here you'll find intel latest RST, try installing that and report back the results.

Who knows what gigabyte has on their web site. In general, try avoiding vendor specific drivers unless you absolutely need some included feature.

ssd firmware should not be an issue, it works ok on other board, from those results it has to be 0009. However, update it to 0309 when you have time to get rid of 5200hrs bug.
 
Once I finish my mods and get both rigs up and running, I'll run a boot-up test and post back.

Thanks, dragonstongue.
 
here you'll find intel latest RST, try installing that and report back the results.

Who knows what gigabyte has on their web site. In general, try avoiding vendor specific drivers unless you absolutely need some included feature.

ssd firmware should not be an issue, it works ok on other board, from those results it has to be 0009. However, update it to 0309 when you have time to get rid of 5200hrs bug.

Sorry, ivan. I installed it, but boot-up is exactly as long.

It's weird, though.. It drags forever at the "Starting Windows" page, but then right afterwards is so fast that it doesn't even show the "Welcome" screen. In fact, sometimes it is so fast, the Windows jingle is cut off. So, it's odd.. it's like a momentary bottleneck followed by an explosion, or maybe it's working behind the scenes.
 
ok, please post CDM benchmark again. Your initial windows benchmark was way off.

It looks like the reason for preboot slowups might be that ud7 is filled with LOTS of gadgets that needs to be initialised first in bios/efi, doesn't matter. Since boot time is consisted of 2 processes, bios loading and os loading after that we'll need to figure out what causes issues.

You can test that bi puting win instalation dvd in and timing how long it takes for install to initialize. If that is what takes a long time, there is no help except trying different bios version.

Also, possibility that comes to my mind is windows are waiting for something on board to initialise or for some driver to load that consumes lots of time, but I'd say that's in no way related to ssd speeds that we're trying to fix here.

edit:
sry, I'm at work and didn't read your post thoroughly, so lag starts when windows starting background loads or before that? If after screen load, that's interesting. If I were you, I'd save a bios profile and than disable everything, I mean EVERYTHING including lan, audio, usb3, the lot in bios and start windows 2 times, second time so windows don't expect some hardware anymore just to see how it'll behave.

I'd love to get hands on that motherboard with it's issues :D
 
Last edited:
Okay, will disable everything and report back.

EDIT: That seems to have done it! :)

Well, for the most part anything.

The "Loading Windows" screen now takes about as long as it is supposed to.

I still have the "issue" of there being no "Welcome" screen. It just staggers for a second (black screen), and then it directly shows the desktop.

Anyway, I disabled - Azalia Audio, USB 3.0, Marval GSATA3, ESATA3 and LAN.

But then I enabled LAN and it still works. Weird thing, LAN1 is actually the one to the right (thought it would be the opposite?).

I don't need ESATA or whatever GSATA is, and apparently I'm not using the Azalia Audio, because I'm using onboard but audio works fine.. but I need USB 3.0. I will enable it and edit again.

EDIT2:

Aww, shit! I enabled both USB 3.0 controllers (apparently, I have two), and we're back to slow boot-up..

So, everything I don't need isn't causing the problem and everything I do need, is..

I'll try to disable either one and see which one is causing the trouble (if not both)..
 
Last edited:
yes, you have two usb3, one for back panel and second for front (input slot on motherboard). Try searching for some other driver or problem with that model of usb controller, you'll probably stumble upon a solution if there is one. :)

about no welcome screen, don't worry about it, sometimes it happens when computer isn't able to process it because of too fast load. Missing screen happened to me on win 2k3, it's nothing to be alarmed about. If you set a password, you'll be greeted by win for sure, hehe :)
 
yes, you have two usb3, one for back panel and second for front (input slot on motherboard). Try searching for some other driver or problem with that model of usb controller, you'll probably stumble upon a solution if there is one. :)

about no welcome screen, don't worry about it, sometimes it happens when computer isn't able to process it because of too fast load. Missing screen happened to me on win 2k3, it's nothing to be alarmed about. If you set a password, you'll be greeted by win for sure, hehe :)

No, no, I have two USB 3.0 controllers for the back panel alone..

I mean, the first 4 ports are controller 1 and the last 2 are controller 2.

And, uh.. it does't matter what I do, if EITHER of them is enabled, the boot suffers.

Also, enabling or disabling causes some serious instability in my system. It made my 12-hour Prime95-stable overclock fail to POST. No problem though, I just re-set the multiplier and it's fine.

But honestly, I'm not even sure if the boot is any bit faster with USB 3.0 turned off..

I mean.. How do I explain..

The Windows icon does load faster, but by "faster" I mean it freezes before it can even fully form and then Windows loads.

Except! That Windows doesn't automatically load - there is a black screen for about 2 seconds.

On the ASUS, it would freeze and then the Welcome screen would come up immediately, no black.

*sigh* I don't know. All I know is, I need USB 3.0.

EDIT:

I found that my motherboard has two Renesas D720200 chips and two VLI VL810.

The weird thing, they are BOTH USB 3.0 controllers.. which means that there are no USB 2.0 controllers..

Not really sure why they decided to wire USB 2.0 ports to a USB 3.0 controller..

But searching Google found no issues with boot-up :(
 
Last edited:
what really puzzles me is why are you bothered by few seconds of boot time? how many times a day do you turn your computer off? If many, why not simply put it to sleep and restart every now and than?

That is drawback of having high end board with lots of "new" tech. :)
 
what really puzzles me is why are you bothered by few seconds of boot time? how many times a day do you turn your computer off? If many, why not simply put it to sleep and restart every now and than?

That is drawback of having high end board with lots of "new" tech. :)

Because you're not supposed to put an SSD to sleep.

But no, really, I just think that the longer boot time means lower performance in Windows, and that does bother me.

Besides that.. it just feels weird that on the cheap P8P67-M Pro, I get instantaneous boot-ups and on the super-expensive P67A-UD7, it looks like I'm running on an HDD.

I mean, why buy a 500$ SSD if I feel like I'm running a 5400RPM HDD?
 
whoever told you that sleep is bad for your ssd is simply telling you a bunch of crap. Sandforce controllers had/have issues with s3 state, but others work like a charm and nothing happens to them.

Hybernation on the other hand is mostly recommended to be turned off because it saves some space on a disk, nothing else. And of course reduce writing all your memory to disk every time you stop using your computer, but if that's 1-2 times a day, who cares?!

Boot time itself doesn't mean good or bad performance, it's simple, more stuff you have on your bord, longer it takes to boot. Test app load if you want to see how disk works. And believe me, it's way faster than any 15k rpm sas disk at all tasks. You buy $500 ssd so your photoshop loads in 1/3 of a time, and acrobat reader loads instantly, your was server redeploys in 1/20 of a time and similar reasons.

High end MBs don't necessarily have to be better than lower models, mostly they have some more bios options an sometimes more powerful voltage regulation, but majority of price goes to the gadgets and better name, and you pay more for the same product because you don't use all that bord offers (talking hypoteticaly).

do try to install latest drivers for your usb though, maybe it helps
renesas drivers
p67ud7 has vl810 hubs, so install drivers for them too.
via drivers

other than that, I honestly don't know what else to tell you except that if you were satisfied with asus board, you should use that one. There is just no rule here, who knows how next generation will turn out to scale, perhaps sapphire will have best MB, anything is possible :)
 
whoever told you that sleep is bad for your ssd is simply telling you a bunch of crap. Sandforce controllers had/have issues with s3 state, but others work like a charm and nothing happens to them.

Hybernation on the other hand is mostly recommended to be turned off because it saves some space on a disk, nothing else. And of course reduce writing all your memory to disk every time you stop using your computer, but if that's 1-2 times a day, who cares?!

Boot time itself doesn't mean good or bad performance, it's simple, more stuff you have on your bord, longer it takes to boot. Test app load if you want to see how disk works. And believe me, it's way faster than any 15k rpm sas disk at all tasks. You buy $500 ssd so your photoshop loads in 1/3 of a time, and acrobat reader loads instantly, your was server redeploys in 1/20 of a time and similar reasons.

High end MBs don't necessarily have to be better than lower models, mostly they have some more bios options an sometimes more powerful voltage regulation, but majority of price goes to the gadgets and better name, and you pay more for the same product because you don't use all that bord offers (talking hypoteticaly).

do try to install latest drivers for your usb though, maybe it helps
renesas drivers
p67ud7 has vl810 hubs, so install drivers for them too.
via drivers

other than that, I honestly don't know what else to tell you except that if you were satisfied with asus board, you should use that one. There is just no rule here, who knows how next generation will turn out to scale, perhaps sapphire will have best MB, anything is possible :)

Actually, it was dragonstongue who said so (on this thread).. uncomfortable..

I want to use the UD7 because I can get 5.1Ghz stable on it, and only 4.8Ghz on the mATX. Maybe the 24 chokes vs 4 on the ASUS?

I was just so sure that programs were also loading slower..
And I am talking about a fresh install, nothing on it.
 
:)

you don't have to use sleep if you dont want, that was just a suggestion. Bud proof it can be used is apples air for example, that's default power down method as i understand. Second, most ultrabooks today say their system boots in seconds, that's true only for sleep scenario and manufacturers wouldn't risk damaging disks on large scale for little bit of marketing, would they?

a real life example is in company I work, there is about 40 computers using ssds that are put to sleep almost every day when we go home to carry our notebooks with us. Some shut down their PCs, but most don't, no need. And there was only 1 problem during last 18 months that we have these devices. And that disk was DOA. However, there is not a single sandforce, only intel g2s and kingston v+100s

Yes, maximum overclocking is definitely influenced by how powerful VRM is plus some bios tweaking a company does.

Please run CDM again, I'd really like to see results now, you can only run 4k or 4kqd32, that's enough.
 
Last edited:
My SSD also takes a bit at startup window(one where windows says loading) takes maybe 5 seconds looks like it wants to crash(it hitches a bit) but then into windows, and all the gadgets and such are loaded in like 10 seconds.

I had seen in other places before to make sure SSD do not go into sleep states, it keeps the drive semi-active and may be writing extra info to the cells for nothing. Not to mention, it doesnt help the drive TRIM and such as it needs to do. Hibernation is also a thing to turn off, as you outlined above, extra writes to cells by dumping memory to disk, cells have limited number of writes before they lose thier performance/life. Also as mentioned TRIM needs to do its thing, having it in hibernate gives it extra work to do.

when I want to save power, I turn off monitors, I also go to either shutdown, or once a week or so, log off. this reduces power draw alot, and lets the drive do its thing as well :)

You noticed a performance bag with the USB, is it plugged into the board via an extension or? there might be a way to source which chip is causing the issue, also on gigabytes page, youll notice the NEC usb driver. Its generally better to deal with the actual maker NEC, Intel or whatever, but sometimes the baord maker "tweaked" the chips and such. I generally will use the drivers on the vendors page(gigabyte, ASUS etc) before I go to Intel, AMD and such. but thats just me.

take a watch, time it from full off to fully good to go, it maybe not taking as long as you think. Higher end motherboards now, are mostly for better component usage(the usb chips and such) power phases(less power equired for same clocks) reduced temps at high power draw etc. Generally the one thing that sets them apart is the extra functions for overclocking and such. my board is almost identical to the one slightly above it except its not meant for using 3 or more gpu and it will not hit quite as high a clock speed, close though.
 
Wow, well.. disabling the rest of the SATA ports really blew performance up.

screenshot2012021715483.png


Only one problem - boot up is now slower! :(

Not only does the "Loading Windows" screen last longer.. but the Welcome screen now sticks for 5 seconds(!)

Also, the VLI drivers say they cannot recognize compatible hardware.

P.S. Could I RAID 0 my 128GB and 256GB M4 drives? I know I will only get 256GB put together, but in terms of performance, it would be interesting, no?

I just wonder if it will damage them..
 
Those speeds are much closer to what they should be.

Also the firmware on the Crucial M4 alot of review sites showed the increased performance. For me, 10-15 seconds to get to windows loading screen 5-15 seconds for windows to do its thing, desktop another 5-10 seconds for it to finish loading, all told, about 335-40 seconds. SSD are not instantaneous loading, the cpu and such has alot to do with processing the info as well.

The asus board might be faster, try just cleaning the extra crap out with CCleaner and letting the drive run without you benching it or whatever for a couple hours. Also, hit some of the links I provided to see if youre numbers are kind of matching some of the reviewers numbers. There will always be some lag for the drive to go into windows, there is with mine, and I am using an Agility 3 a sandforce based drive *gasp*
 
great speeds, that's how it's supposed to be.

you can raid0 smaller drives, but if I'm not mistaken, that will additionally increase boot time. Have never done that myself, however, so that's just my logic.

speed increase should be from RST installed, not from disabling marvell controllers, you can power them on any time if you want, in case you need more disks.
 
great speeds, that's how it's supposed to be.

you can raid0 smaller drives, but if I'm not mistaken, that will additionally increase boot time. Have never done that myself, however, so that's just my logic.

speed increase should be from RST installed, not from disabling marvell controllers, you can power them on any time if you want, in case you need more disks.

I don't. I have a NAS.

But seriously, can I RAID 0 the 128GB M4 and the 256GB M4? I'm dying to see 1000MB/s Reads!
 
oh, you want to raid a 128 one and 256 gb one. Huh, I have no idea.
Its probably possible, but I think you'd end up with 256GB raid0 volume.

Someone else would be better at answering that. Or... You can always try and see what happens :)
 
Are you using intel or MS ahci drivers? I always use MS drivers. They seem to work better for me.
 
I could be wrong, but its probably impossible to raid 2 different size drives, or for that matter, drives using different controllers. Beyond that, you will want to make sure TRIM and BGC are enabled in a RAID format, ALOT of drives in raid lose thier important features, and just gain speed, speed is irrelevant if it kills the drive way faster :p

Fresh install, and a cell refresh/secure erase, or whatever its called in the M4 case are totally different things, the controller on most SSD keep track of hours on, cell performance etc, only be "refreshing" the controller will these bits be 100% "fresh"

although I did state, the last numbers you posted seem to be around where they should be - a little bit, so it may be coming down to the drivers for the SATA, RST or even possibly the firmware currently on the drive.

I also use MS AHCI drivers, but switched to AMD based as soon as I booted into windows, in this case, MS/Intel to the actual SATA makers AHCI driver would be better. Corsair themselves recomends what I just said, stick with MS/Intel/AMD AHCI drivers unless there is problems/performance issues, then try the manufacturers AHCI drivers, Historically speaking, Intel has the best SATA performance for SSD, but this also related to Intel SATA 6 which is only z68/x79 boards to my knowledge.

I am using Jmicron on this board, no performance issues that I have noticed, but I did do the base driver, booted went MS AHCI rebooted turned on AHCI, back to windows got the newest SATA drivers for my A99X EVO, there is a proper process, in your case OP, you said you tried and it didnt help, so it could be the SATA itself, the drive not being refreshed to a "like new state" or the firmware itself.

I just want to point something out here, I have read this multiple times, for all brands of SSD using different controllers. Formatting for an SSD is NOT the same as formatting a regular HDD, as mentioned the bits get used up, and the controller can clean them, but the controller doesnt "flip" them, with a regular HDD this would be akin to writing 0 or 1 to the drive, for SSD it would be the maker, Corsiar, Crucial etc giving a program designed to do this, to bring the drive back to its "spec" levels. Though 100% used cells are unable to be used again, this is by design, nothing that can be done about that side of it :)
 
Back
Top