NEC 2490 WUXI hours

Mine is half as bright at 12000 hours.

New was 140-400.
Now is 70-200.

20000 might be a reasonable practical lifetime.
 
SpectraView software tells me how many hours usage on the monitor. I have 8,198.4 hours usage and just wondering how long a monitor like this is good for.
 
How is it possible to see the amount of "backlight hours", i.e. for how long it has been on?

EDIT: That being said, i'd assume the brightness to decay exponentially.. but this is just a guess on how mercury depletes in phosphor.
EDIT 2: Last figure in http://www.sanken-ele.co.jp/en/prod/semicon/pdf/2005ccfl_07e.pdf seems also to suggest that.

That last page is interesting as it shows how much faster the whole system deteriorates compared to just the CCFL lamp itself.

The whole system deterioration rate is much more comparable with what I am seeing.
 
I own its larger brother, the NEC 2690 WUXI (came with a Polarizer).
Until this thread appeared I never bothered to check how many hours I have on it.
I purchased the display in June 2008. My SpectraView II now reads 14,412 hours of use.


Last year the On/Off power button encountered what appears to be a contact problem, requiring having to tap it a few times before it "takes". That anomaly could have resulted from my own doing, one day I got a little ambitious with my liquid screen cleaner permitting some of it to drip down the screen into the margins behind the rows of buttons. The power button started acting up from then on. Rather than continuing to fiddle with the power button or have it replaced I just stopped using the power button. There is really no necessity for me to ever use the power button because when I shut down my computer the display goes into sleep mode, plus I configured Windows to put the monitor in sleep mode after 15 minutes of computer inactivity

Other than the temperamental power button I have had no problems with it. It had no stuck or non functioning pixels when it was delivered and still has no pixel problems. I have never felt a need to adjust the brightness or the contrast, maybe this is because I have continued to use the same calibration setting I created 3 years ago. Am assuming from what others in this thread have posted, if I measured the present maximum brightness (which I don't know how) I would see some concrete value indicating deterioration - but, like I stated I have never found the need to manually adjust the brightness despite it being in use for 37 months.
 
Last edited:
Slightly off topic perhaps, but It would probably be stupid to start a thread for a single question.

I have an european LCD2490WUXi, originally bought without SVII or a hardware calibration unit. Can I just get a http://www.necdisplay.com/p/spectra-view-kits/svii-pro-kit?cat=LargeScreenDisplays and it will work without problems?
It seems to not be widely discussed, but this post seems to indicate something else: http://hardforum.com/showpost.php?p=1032758895&postcount=13 ... If this is true, what Basiccolor bundle is identical to SVII? To be honest all of their products and bundles look much more high-end, and the prices naturally reflects this.
Prad says it it possible whenjust using the SVII package by NEC, which I'll probably be able to find from a reseller in the US: http://www.prad.de/en/monitore/review/2009/review-nec-2490wuxi-part12.html#Calibration
 
Going from memory, certain firmware revisions of the 2490WUXI-BK (non-SV) versions had this ability, and then certain ones (around early/mid 2008 and later) seemed to remove this ability. There was a change that could be enacted through the extended OSD on the screen that allowed SVII to re-calibrate the monitor LUTs even on Euro-Non-SV versions.

Having tried BasicColor Display 4 (full version, purchased) on my 2690WUXI-BK (non-SV) I was not able to update monitor LUTs. I don't know about the latest BasicColor Display 4 version, but I'll try it out tonight or tomorrow night and see, once I get my updated/upgraded licence, as I recently formatted my main PC connected to both the 2690 and 2490WUXi2.

If worse comes to worst, tk-don, you could always download a trial version of BasicColor Display 4 and try it, if you have a supported colorimeter like an Eye One Display or Spyder 2/3.

Slightly off topic perhaps, but It would probably be stupid to start a thread for a single question.

I have an european LCD2490WUXi, originally bought without SVII or a hardware calibration unit. Can I just get a http://www.necdisplay.com/p/spectra-view-kits/svii-pro-kit?cat=LargeScreenDisplays and it will work without problems?
It seems to not be widely discussed, but this post seems to indicate something else: http://hardforum.com/showpost.php?p=1032758895&postcount=13 ... If this is true, what Basiccolor bundle is identical to SVII? To be honest all of their products and bundles look much more high-end, and the prices naturally reflects this.
Prad says it it possible whenjust using the SVII package by NEC, which I'll probably be able to find from a reseller in the US: http://www.prad.de/en/monitore/review/2009/review-nec-2490wuxi-part12.html#Calibration
 
Hmm, the setting in advanced OSD seems to be in tab E, where it should be possible to enable/disable SVII by pressing Up+Input simultaneously. Unfotunately, absolutely nothing happens on my 2490 when I do that. It was bought in Germany and manufactured in Feb. 2009. :(

I don't have a colorimeter yet - i'll just need to know if the software can communicate with my monitor.
But if it can't communicate with it, why is NEC advertising the 12 bit LUT on the 2490/2690 in Europe, if it can't be accessed?
 
SV II will work, BasICColor requires a SV modell in your case.

why is NEC advertising the 12 bit LUT on the 2490/2690 in Europe, if it can't be accessed?
You are utilizing it and its advantages in a non hardware calibrated workflow too. The input signal is processed accordant to your OSD adjustments.

Best regards

Denis
 
Hm, yes that is of course true. :)

The 2490 you used in the review on Prad, did you have to set anything in the OSD to make it work with SVII? Do you remember if it was possible to enable/disable the possibility to use SVII in submenu E in the advanced OSD?
 
Back
Top