5870 to reference board or not to reference board?

maliclipse

Weaksauce
Joined
Oct 19, 2007
Messages
101
If you were looking for a brand new 5870, would you look for a reference board or would you look for a rev2?

I have a pair of Gigabyte rev2 (ultra durable edition) 5870s in CFX and noticed that one runs 20-30 degrees higher than the other because they're next to each other on the mobo. Even though both gigabyte cards have two fans on them each the problem is that the fans don't blow the heat out the case so even with a 120mm case fan blowing right on the cards one card overheats because it doesn't suck air in and out the back.

I'm thinking a pair of reference boards spaced out by one slot would be a better solution because they'd be able to suck cool air in and out better.

Thoughts?
 
I have a pair of Gigabyte rev2 (ultra durable edition) 5870s in CFX and noticed that one runs 20-30 degrees higher than the other because they're next to each other on the mobo.

When they're idle the master card will run about 20C higher due to its idle clocks being much higher than the slave card. Is yours still 20C-30C higher at load too?
 
Yep, at load GPU1 goes to 75 and GPU2 goes to 98-100. This thing shut down on me once already during a Heaven benchmark.

I ordered a longer crossfire bridge so i can space the cards out.
 
Using the ATI overdrive function, you might want to push the GPU #2 fan duty cycle up to 75% or even 100% under 3D load.

If your #2 is the slave, it will essentially shut down in 2D, but if it can't breathe it will cook in 3D format.

Overdrive will allow you to run the fans at different cycle speeds.

I have two "reference" E6 cards with a PCI-e space between them and they run at about 65C under full load at 45% Duty cycle.
 
My 5970 starts to throttle at 90C (hitching). Depending on ambients, I have to crank to 70% duty cycle at times.
 
Yep, at load GPU1 goes to 75 and GPU2 goes to 98-100. This thing shut down on me once already during a Heaven benchmark.

I ordered a longer crossfire bridge so i can space the cards out.

Wow that's hot! lol

How come you cant put one slots space between them? Does your mobo not support that config? The standard CF bridge is long enough to allow that. That's how I'm running my CFX 5850s right now (one on 16x and one on 8x - will move to 2nd 16x slot when my long CF bridge comes in).
 
In my case the stock cfx ribbon isn't long enough since I need to jump two slots.

My cards idle at 42 and 65-68 respecitively in a room that is 75 degreesish
 
Silly question, for two 5870s do i need one ribbon or two?

Just one, but two won't hurt anything.

ASUS estore used to sell them for 15 bucks.

Now the only place I see them is eBay for more than that.:eek:

I wrote ATI about getting rid of the little short bridges they give out with the GPUs and using only long flex bridges (100mm) so we can adequately space our cards on MBs that can accomidate it.
No answer yet.:(
 
Thanks for the quick reply.

I ordered one off of Ebay for 23$ shipped. Price but will be worth it in the grand scheme of things.

Good luck on getting an answer from Ati. :)

MH
 
Silly question, for two 5870s do i need one ribbon or two?

You only need one. Two may cause artifacting. I noticed that with my CFX 5850s I would get tiny pixel artifacts every once in a while using two bridges. Using one bridge seems to have solved the problem. It was especiallly annoying on [H]ard's black background.
 
You only need one. Two may cause artifacting. I noticed that with my CFX 5850s I would get tiny pixel artifacts every once in a while using two bridges. Using one bridge seems to have solved the problem. It was especiallly annoying on [H]ard's black background.

I use two, always have.
No problems.:D

Used two with SLI even though everybody says no.
 
Back
Top