SSD Boots too Fast for Ethernet

ihmcguinness

Limp Gawd
Joined
Nov 15, 2007
Messages
473
I might be wrong, but ever since I installed an Intel 80gb SSD, my computer seems to boot so quickly that my ethernet connection is the slowest thing to load. The computer will be all ready and I can open other programs, but for about 20-30 seconds after windows 7 comes up, I get the little exclamation point icon over my ethernet connection icon and no pages will load. after that, its all normal.

is the ssd the culprit?

my motherboard is a Gigabyte p55-ud4p.
 
I doubt it, because my main rig does the same thing, and it's not on SSD (3 WD 640GB Blue in Raid 0). I'm trying to troubleshoot the problem myself, and all I've found is that I didn't have the problem with XP. I'm running Intel Pro NICs, so I don't think it's that. It's gotta be either windows 7 itself, or the router.
 
Have you tried just opening your browser and seeing if the connection up? I noticed windows 7 is abit slow displaying your connected down in the start bar. I don't have an SSD. But yet at startup i can still open my browser and get my homepage.
 
i can open the browser, but it won't connect to anything during that time. it will connect a few seconds before the icon says it can, but its still like 20-30 seconds
 
can you ping out? do you have multiple nics? can you assign a static ip instead of getting one from your router?
 
can you ping out? do you have multiple nics? can you assign a static ip instead of getting one from your router?

I've noticed OP's problem too.

the PC is probably waiting on DHCP.

I think I've had the problem since I switched back to DHCP

I'll test it with a static IP later when I get home.
 
I've got a similar network setup to okashira. WNR3500 behind Uverse modem in DMZ. I don't think it's DHCP as I can see my network and have an IP address. It seems to be Windows detection of the Internet connection. I don't know enough about how Windows does that to troubleshoot much further.
 
It is not a SSD problem, my main computer has done the same thing since I have been on Win 7 with a regular HDD or an SSD. In fact I have 4 computers (3 hardwired and 1 wireless) on Windows 7 (32 bit and 64 bit) that have done the same thing since I installed Win 7. The SSD does make the problem more noticeable however. I am behind a Netgear 3700 but it did the same thing with the previous Linksys WRT54GS
 
Could also be a STP issue on the switch. Spanning Tree Protocol could delay the port becoming active for 30 seconds to verify that there is no loop. It's a good thing to have, but if you just have one switch you could safely disable it or perhaps try RSTP Rapid Spanning Tree Protocol and set the hello time to 2s.
 
if your driver is not WHQL certified it can take much longer to load. my wireless use to take like 10 seconds extra to show up after the PC booted. i just did a update in the driver via windows update it changed the driver and worked smooth again. i have never seen the issue with ethernet before but, i imagine it could be a similar problem.
 
lot of issues going on with the wrt610... check out linksys forums and make sure you have the latest firmware.

There is a work-in-progress DDWRT firmware out there for the 610.
 
that's not 9.5 seconds, more like 30

He's not counting the time it takes the BIOS to load, just from when windows starts booting from the drive; since before that the drive is sitting there doing nothing.

OP, it sounds like crap NIC drivers to me. Maybe try out some older ones if you're already using the newest?
 
If it continues to be a problem, and you don't move your machine to different networks, just set the IP to static.
 
He's not counting the time it takes the BIOS to load, just from when windows starts booting from the drive; since before that the drive is sitting there doing nothing.

OP, it sounds like crap NIC drivers to me. Maybe try out some older ones if you're already using the newest?
I know, it's just a misleading way of measuring in my opinion.
I consider boot time the time from when you press the power/reset button until you see the windows desktop.
 
I have this issue with a 7200RPM harddrive as well on the rig in my sig. I think it is a combination of issues that finally just stacked up high enough to be visible.
 
Back
Top