P35 DS3L broken capacitor advice

cory1234

Weaksauce
Joined
Dec 4, 2009
Messages
116
My ds3l has a broken capacitor...I tried replacing the NB heatsink without removing the MB from the case..really stupid idea.

Anyways I wanted to get some input from anyone that has ever replaced a capacitor.

There is a picture about half way down the fourth page.
http://www.overclock.net/intel-motherboards/693687-knocked-off-capacitor-help-4.html

Would I be able to solder that capacitor back onto the leg? If not where can I purchase an exact replacement? Is it safe to solder with the cpu/heatsink still attached?
 
You should be able to solder it back on providing the legs aren't broken or cracked too bad. Honestly I would just replace it since it's already off and may have been damaged when you took it off. I'm not sure where you can get another capacitor. I'll look or maybe someone else will know.

I would take the cpu/heatsink off. There's going to be heat from soldering it on and you don't want any solder to get on it. ;)
 
Did you take a look at the picture? I'm tempted to resolder it but I have no clue if it will even work. I accidentally threw away my full tube of AS5 and a replacement is on its way. Thats why I mentioned removing the cpu.
 
Did you take a look at the picture? I'm tempted to resolder it but I have no clue if it will even work. I accidentally threw away my full tube of AS5 and a replacement is on its way. Thats why I mentioned removing the cpu.

Yea, I thought it was just a picture for reference not the actual one. :eek:

Looking over those pics again zoomed up this time (small screen), that cap looks SOL, your going to have to get a new one. This place looks legit, http://www.mouser.com/ You would just need to get the part number off of the cap.\\

There was other caps in these spots as well, correct?

4455776058_fe044104d1_o.png
 
Last edited:
Looks like you've pulled the internal contacts right out, the capacitor is ruined and you'll need to replace it. It appears to be a Panasonic FL series; I can't read the value from any of these pictures. The FL series seems to be either a special series or discontinued, but the FM series should be a suitable replacement and is easy to get from Mouser or DigiKey. Just find out the value, voltage and measure the lead spacing. How many did you manage to damage this way?
 
You guys are looking at the reference pics. Scroll down to the post by cory1234 ;)

I only managed to damage one capacitor...I tried cutting out the heatsink...honestly I don't know what the $#%# I was thinking. I got one side out and then tried to rip and twist it out when I knocked one over.
 
Last edited:
Oops! Reconnecting the lead might work in this case, it looks partially damaged but may still operate reasonably. I'd just replace it. Sanyo OS-CON are somewhat difficult to get; the link you were given in the other thread seems a reasonable source if you just need one of them, though the price is obviously high it might work out cheaper after shipping from one of the normal vendors, and you can get the exact part and not a sub.

Nichicon PLF0E821MCO6 is suitable from Mouser. UCC APSC2R5ELL821MH08S would also be suitable, available at DigiKey. I wouldn't use the Rubycons you linked, they're not polymer caps and have a much higher ESR. Probably would still work, but they're not direct subs for the damaged one.
 
????????
A poster in your thread on the other board provided both a correct identification and a source for replacement caps.

Sanyo SEPC 2.5V 820UF OS-CON Aluminum solid Capacitor

http://cgi.ebay.com/4-Sanyo-SEPC-2-...ultDomain_0?hash=item45ee5efb4e#ht_3572wt_939

If you can solder its a 10 min job to desolder and remove the old leads and solder the new ones in.

As far as the heatsink, I dont understand, whatever is best so you can get good access to the work area. Those caps have nothing to do with the heatsink other than being in the way when the forces of destruction where unleashed. And yes you will have to remove the motherboard from the case to do a proper solder job. If nothing else was damaged you should be fine.

If you are not comfortable with soldering you might be able to find a tech locally (look in yellow pages for Electronics Repair or TV repair) that should do it for $10 or so if you can catch him/her in a good mood and have the board out and parts in hand ready to go.
 
As an eBay Associate, HardForum may earn from qualifying purchases.
If you are not comfortable with soldering you might be able to find a tech locally (look in yellow pages for Electronics Repair or TV repair) that should do it for $10 or so if you can catch him/her in a good mood and have the board out and parts in hand ready to go.

Yea if you live in the Ohio area. I can hook you up no problem. PM me.
 
Yeah as Bill mentioned, you've got the CAP replacement link already. Just bust out the soldering iron and fix it. Just be careful not to over solder and burn the trace on the mobo. If you're lucky you should have a little bit of solder left on the board, just get a fine tip and warm up the solder by touching the solder only and not the motherboard, poke the capacitor through it and then cut the excess leg from the underside of the mobo after the solder has hardened.

On your thread there was mention of conductive glue and whatnot. It's not a good idea, because during the heating up and cooling down, the expand/contract cycle will eventually effect the contact of the CAP with the motherboard. Solder is best.

The capacitor joints are alot easier than ICs and a bit more forgiving, if you've got a steady hand it's not too difficult, just take it slowly.

Good luck with that...
 
Back
Top