Intel and V-raptor Benches.

Copyright

Supreme [H]ardness
Joined
Nov 17, 2000
Messages
6,004
Ok here are some benches ive been working on. All drives are being ran as an OS drive when doing these benches. Using ICH9-R but found I had to use the older Intel matrix driver when using RAID or I would recieve blue screens. The Firmware on the controller seems to be the same version of the Intel software I installed. I tried installing the newer Intel matrix driver that has some speed fixes for the Intel drives but I get blue screens. I assume I need to upgrade the controller firmware on the ICH9-R? I can't seem to find any way of doing this. I have the latest Asus firmware on my board. Thx for any help! I expected better Crystal mark scores but not sure I trust them that much. I changed a setting nad it showed my read speeds of 1007mb/s which I know is not right. Let me know if there are any other benches I should try with the RAID 0 setup.

150g V-raptor (IDE Mode)

Vraptor150gAHCI.jpg



Single Intel X25-M 80gb (AHCI)

SingleIntelSSDX25M80.jpg



RAID 0 Intel X25-M 80gb

INTELRAID0CDM.jpg



Again RAID 0 INtel X25-M 80gb

INTELRAID0.jpg



I used SSD Tweaker to make all my setting changes. The one I leave checked I do for a reason. Takes forever to shutdown if you uncheck it. Please let me know if I should make any changes. OS is Vista 64bit

Settings.jpg
 
If you have 6GB of ram or more, you could try disabling your page file. It sounds like it possibly takes a while to clear the page file on the drive during shut-down... just a guess though

Random Write at 4k though is incredible- I have seen no other drive get anywhere near that. If you could download and run the MFT benchmark from www.managedflash.com I'd appreciate it. Don't install the driver when it asks you, no need to. Just run the built in benchmark. Thanks-
 
If you have 6GB of ram or more, you could try disabling your page file. It sounds like it possibly takes a while to clear the page file on the drive during shut-down... just a guess though

Random Write at 4k though is incredible- I have seen no other drive get anywhere near that. If you could download and run the MFT benchmark from www.managedflash.com I'd appreciate it. Don't install the driver when it asks you, no need to. Just run the built in benchmark. Thanks-

Can I do this with it as an OS drive? Im not abouto whip it after finally getting it stable lol
 
If you configure it to run MFT, then no, you can't run it on an OS drive. However, you can install the software and run the benchmark. The software doesn't "kick in" till you configure a an MFT partition on a drive. So, just run the program, and choose not to install the driver when it asks. Even if you do install the driver,it's not going to mess anything up-

If you're not comfortable with it, don't worry about it-
 
If you configure it to run MFT, then no, you can't run it on an OS drive. However, you can install the software and run the benchmark. The software doesn't "kick in" till you configure a an MFT partition on a drive. So, just run the program, and choose not to install the driver when it asks. Even if you do install the driver,it's not going to mess anything up-

If you're not comfortable with it, don't worry about it-

Ill pass on that bench... ive loaded this thing like 5 times here lately and im a bit tired of jacking with it. I still want to find out if there is a firmware update or not for my ICH9R controller that will allow me to use the latest software.
 
So... what's the problem? I don't see one, and the speeds are insane pretty much across the board. What could possibly be wrong? :)
 
If you have 6GB of ram or more, you could try disabling your page file. It sounds like it possibly takes a while to clear the page file on the drive during shut-down... just a guess though

Random Write at 4k though is incredible- I have seen no other drive get anywhere near that. If you could download and run the MFT benchmark from www.managedflash.com I'd appreciate it. Don't install the driver when it asks you, no need to. Just run the built in benchmark. Thanks-

Its when I disable the clear page file on the driving during shutdown that I run into the problem. I leave it checked so I dont run into the issue. Using the auto Tweak button it will uncheck pretty much everything but the paging file. I have 4gb of ram.. dunno if I should uncheck it or not.
 
I'm with Joe.

That's pretty much screaming in my book! :D

Your right its giving good numbers and runs well. I just keep thinking why cant I install the 8.7.0.1007 IMSM? The 7.5.0.1017 version works but the 8.7 gives me blue screens. If I dont use the IMSM at all then the system runs SLLLOWWW.


Can someone tell me if RAID uses AHCI.. meaning will i get NCQ etc? I could not find an option that could turn on AHCI while in RAID.
 
Back
Top