DIY USB Popcorn Maker

HardOCP News

[H] News
Joined
Dec 31, 1969
Messages
0
I have no idea why you’d want a popcorn maker attached to your PC (buttery goodness + keyboard = bad) but its obvious that somebody thought this would be a good idea. Kudos for ingenuity though!
 
LOL, that is great. although I agree that is an odd thing to have attached to your pc.
 
Nice.

I like how the guy is mechanically smart enough to build his own USB popcorn maker, yet lacks the common sense to just flip the metal tin over while the glass jar is attached instead opting to dump the popcorn from the metal tin into the glass jar spilling the popcorn all over the place in the process.:D
 
That would save a couple of trips to the microwave considering the amount of popcorn I consume on a weekly basis.
 
Nice.

I like how the guy is mechanically smart enough to build his own USB popcorn maker, yet lacks the common sense to just flip the metal tin over while the glass jar is attached instead opting to dump the popcorn from the metal tin into the glass jar spilling the popcorn all over the place in the process.:D

Wondering the same thing.


In japan they have everything you can imagine powered via USB...I mean even BOB (if you have a dirty mind you will know what BOB means).
 
I call BS. This would kill most every USB port out there, he has those 2.5V bulbs wired in parallel with a 5V source (USB) which would be drawing well over an amp from the usb port. USB ports are only rated to do 100mA typically, 500mA max. Plus, the cut scenes make it clear that it's faked, along with the fact that you couldn't pick up the hot metal can after it had been popping.
 
I call BS. This would kill most every USB port out there, he has those 2.5V bulbs wired in parallel with a 5V source (USB) which would be drawing well over an amp from the usb port. USB ports are only rated to do 100mA typically, 500mA max. Plus, the cut scenes make it clear that it's faked, along with the fact that you couldn't pick up the hot metal can after it had been popping.

He also did place the bare metal on the table. You make a good point though.
 
I don't get the fascination with powering things off the USB ports. What's so difficult about plugging things into a wall outlet or using batteries? Or am I being too practical to notice the coolness factor of these devices?
 
I call BS. This would kill most every USB port out there, he has those 2.5V bulbs wired in parallel with a 5V source (USB) which would be drawing well over an amp from the usb port. USB ports are only rated to do 100mA typically, 500mA max. Plus, the cut scenes make it clear that it's faked, along with the fact that you couldn't pick up the hot metal can after it had been popping.

The first thing i thought was you can't pull that much power from a USB port. .5*5V=2.5 watts. I am only an EE, and don't know THAT much about thermo, but I am pretty sure its pretty hard to pop popcorn with 2.5W.... hell just trying to heat the metal cup in ambiant air would be near impossible.

"On average, a kernel will pop when it reaches a temperature of 347 degress Fahrenheit (175 degrees Celsius)." from http://recipes.howstuffworks.com/20-things-you-didnt-know-about-popcorn1.htm

I don't see a possible way to keep that cup at 347F with whats shown....
 
I call shens.. no way he's popping corn with that. they look like christmas tree lights. Probably have better luck with an old prescott. :p
 
Maybe somebody should give this a try. Let us know if it actually works or not.
 
I call BS. This would kill most every USB port out there, he has those 2.5V bulbs wired in parallel with a 5V source (USB) which would be drawing well over an amp from the usb port. USB ports are only rated to do 100mA typically, 500mA max. Plus, the cut scenes make it clear that it's faked, along with the fact that you couldn't pick up the hot metal can after it had been popping.

If you look closely, the box says "150" celsius Heater Light, 2.5v 0.3A" I assume " in that context means degrees? It wouldn't be drawing THAT much more than the rated 500mA, and the kernels are laying flat one kernel deep on the base. The way he sealed and insulated it would mean that very little heat would escape anywhere but toward the base of the can, and normal dispersion would make the can itself able to be held if it were tin.

I think it could work, though I cannot for the life of me find that Rayovac bulb anywhere.

I suppose you could find proof on concept in all those USB beverage warmers and such. Provided you can seal the heat in an enclosed chamber and produce more than the ambient wicks away, it'd just be a matter of time before you could pop corn.
 
If you look closely, the box says "150" celsius Heater Light, 2.5v 0.3A" I assume " in that context means degrees? It wouldn't be drawing THAT much more than the rated 500mA, and the kernels are laying flat one kernel deep on the base. The way he sealed and insulated it would mean that very little heat would escape anywhere but toward the base of the can, and normal dispersion would make the can itself able to be held if it were tin.

I think it could work, though I cannot for the life of me find that Rayovac bulb anywhere.

I suppose you could find proof on concept in all those USB beverage warmers and such. Provided you can seal the heat in an enclosed chamber and produce more than the ambient wicks away, it'd just be a matter of time before you could pop corn.

But unless the device "asks" for more current it is down at 100mA (I believe, might be 150) either way, not enough to do much with...
 
Nice.

I like how the guy is mechanically smart enough to build his own USB popcorn maker, yet lacks the common sense to just flip the metal tin over while the glass jar is attached instead opting to dump the popcorn from the metal tin into the glass jar spilling the popcorn all over the place in the process.:D

You sound like my GF.
 
Back
Top