trouble with gigabyte p35-ds3l

Joined
Nov 24, 2007
Messages
17
Edit:
e6300
gigabyte p35 ds3l
corsair 444-12
500w antec earthwatts

okay i replaced all the parts except the cpu. but i could not oc from 266 ->300 with everything thing on stock. Could the cpu be the problem even though it boots okay on stock speed?
 
Does it boot at stock?

Also try booting with a single stick of ram, and age old, unplug it, reset cmos, and pray.

TBH, I've gotten lots of luck in these situation by just shaking the machine... however that's normally on old P4s or Athlon XP systems :p.

Good luck.
 
I dont think you need fsb and mch at +.3 although I dont see how that would stop it form booting, unless you already killed the chip with to much volts?
 
mch +.3v is WAAAAY too much unless you have some sort of hardcore cooling in place of the stock heatsink on the MCH. Same with FSB volts. You may have already fried your northbridge/mcp.
 
I've just tried swtiching out to my old e6300 trying to run it at same setting but with fsb at 300. I think you guys are right. im just going to try for new board and start slow this time. i dont think the rams are messed up either since they're rated 444-12 @ 2.1v unless the new mb has minimal volt of 2.0v

thanks.
 
Will your old cpu start with fsb and mch on +.1? Or default settings? Try setting you ram on 5-5-5-18 @ +.3 or.4 until you figure this out
 
the FSB voltage should be left alone until a last resort. aye start out with MCH +.1 increase only as needed and silicon RTV glue a 40mm fan to the MCH if you are serious about OCing.
 
oh. i think im confusing you guys and myself. yes, both cpus can fully boot at stock settings. so it might not be the mch being fried? Im just going to get the parts (new mb and rams) to try different combo.
 
Probably your FSB:RAM ratio is at 3 (because when you're using it on stock, the FSB=266 and the memory is 800 MHz DDR, so the multiplier=3). When you are going to 300 FSB, then the memory will run at 3×300=900 MHz !? So you must change the multi on 2 (DDR synced with FSB) :p
There is a high chance to use that e6300 on 300 FSB on stock volts. ;)
 
a lot of people are having problem with this board. and since all my components are new and gone through 2 boards, im just going to give up on this board and go with msi p35-fr or evga 650i. thanks for the replys.
 
a lot of people are having problem with this board. and since all my components are new and gone through 2 boards, im just going to give up on this board and go with msi p35-fr or evga 650i. thanks for the replys.

I don't have any problems with that board and just ordered one to build a system for my in-laws. With E2160 and stock HSF I'm trageting 2.8-3.0Ghz speed. I just hope that your system will work fine with msi/evga board, because it might be your other compents causing this problems. Beside msi/evga look into abit mobos there is a thread about it in the intel mobos section.

Good luck :D
 
I don't have any problems with that board and just ordered one to build a system for my in-laws. With E2160 and stock HSF I'm trageting 2.8-3.0Ghz speed. I just hope that your system will work fine with msi/evga board, because it might be your other compents causing this problems. Beside msi/evga look into abit mobos there is a thread about it in the intel mobos section.

Good luck :D


same here built bro n law system with close to same specs ds3l- e6300 i have his runnin 3.1 on air w/ gemini II cooler and 2 med speed fans.

cause that board did so well i picked up a ds3r for my self
 
Yeah, i was really surprised that both boards didn't work for me. I am gigabyte fan and i loved my 965p-ds3 alot, until i broke it -user error- broken pins. I found that several people from another thread said their system reboots when having fsb enable. I confirmed it myself, by enabling fsb with stock everything, even fsb which for e6300 was at 266, the system fail to boot. Im a bit sadden but i went onto buying Abit ip35-e for sub $100AR from newegg and returned the two p35-ds3l to fry's which by the way has an excellent return policy. Now waiting for the Abi to come in.
 
Back
Top