The Lian Li Gallery

Of the guts or the crap tons of little mods to the case? :D

Both!

Edit: Best bet, if it is a lot of little things, and such would be to start a thread so we can discuss it outside of this thread.
Cause I know I would like to know more about your case, and the work you put into it.
 
Both!

Edit: Best bet, if it is a lot of little things, and such would be to start a thread so we can discuss it outside of this thread.
Cause I know I would like to know more about your case, and the work you put into it.

I agree 100%...just be sure to include me. :D
 
Well I started with a Lian Li v1000B Plus II, I ordered the black mesh drive bay covers and the new Delrin Bulgin Vandal switch. Still do not have the black caster set I ordered at the same time, back ordered. All the fans are Syche S-Flex 1200rpm models that are plugged into fan headers on the motherboard and controlled via the Abit uGuru BIOS/software.

The fans are all soft mounted with rubber fan posts to reduce vibration, even the one for the side panel. When I installed the side fan I changed how the spacer to the sidepanel is. I made the gap between the frame of the spacer and the side panel smaller to help push air out. I tried to soft mount anything that may move or vibrate. There is really no vibration from any components even with the case being known to have a resonance. At worst with all the fans at 12v there is a light vibration through the case but no real resonance. Mainly the sound of the fan motor and the rush/whoosh or air.

I removed the stock hard drive cages and copied another poster in this thread and threw my Raptor in the Silent Drive and stuck rubber case feet on it so it just rests at the bottom of the case. Also, I removed the power supply support after it was fitting real tight and I couldn't get the power supply to set in the back panel just how I wanted. I used a step bit and made the holes in the motherboard tray to run cables. I also used a nibbler a few times enlarging the factory opening to pass cables through so it is now about double the size. I used a metal file to radius all the cut edges so they are not sharp and so I do not need to use and silly grommets. The power supply is mounted using some similar silver thumbscrews to match the cases all thumbscrew method.

There was an error with the switch cables being shorter than they were supposed to and I was really liking the look of all sleeved cabling so I ordered new LEDs when I was sent extensions for the switch. So, now the two 3mm LEDs in the front under the switch are white as well. I removed the cases stock speaker and was going to use the speaker on my motherboard but it dosent seem to be a case speaker. Its an alarm speaker. I may add a speaker back in sometime down the road.

As you can see in the gallery I removed the rear factory grill and just left it open for airflow. The bottom fan runs at 5v and spins upto 7v max since all it is doing is cooling the one hard disc. The side fan and rear fan run at 6v and spin upto 12v as the cpu temp goes up. The fan on the Ultra 120 eXtreme starts at 7v and ramps upto 12v also as the cpu temp increases. The VF900s on the vid card start at 6v and ramp upto 12v with system temp. So at idle the system would be considered "silent" by some or at least "is it on" quiet.

The case is setup to be all negative airflow. High volume low pressure. This is why there are no drives in the front. I wanted the entire front of the case to be an intake. With the air being drawn in over such a large area the air doesn't whoosh in. If I put my hand in front of the case with all the fans at full speed I have to get within a couple inches to feel air movement. I can already see that dust will be much less given the case isn't acting like a vaccume and sucking anything in that gets withing a foot.

Most of the additional mods is the hours I spent fiddling with all the wiring and getting it all to tuck, route, bend, lay flat, or stretch. Plus a good run through the case with some mineral spirits removing any stickers and fingerprints. It amazed me how much time it takes to get one of these cablegami installs.

Stealth -
Lian-Li V1000B Case (with mods)
Scythe S-Flex 1200RPM fans
Corsair HX520 PSU
Abit IP35 Pro Mobo
Intel E6750 Core 2 Duo Retail
Thermalright Ultra-120 Extreme heatsink
Corsair Dominator 2GB (1GBx2) PC-8500 Kit
BFG Tech nVidia 7950 GX2
Swiftech 7595 GX2 spacer kit
2x Zalman VF900 HSF for 7950 GX2
Creative Audigy 4 Pro
Western Digital Raptor 74GB
Scythe Silent Drive
Dell 2405 24" Widescreen
Logitech Cordless Elite Due keyboard
Logitech Cordless TrackMan Marble
AudioTechnica ATH-A900 headphones

I think that covers it all. I did so many little things over the week it took to put the case together that I sear I am missing things. Course that is probably because I routed all the wiring four times and test fit all the parts three times. So, in reality I built this computer EIGHT times! :eek:
 
P1010258.jpg



Is this and this the exact same case as above ? :)


TIA for any help shed on this.
 
Nope...that case in the picture only has (1) rear case fan hole and only (2) 3.5" external bays. The case in those links you posted has (2) rear case fan holes and (3) 3.5" external bays.
 
No i would say its not the 65 B(the cased you linked too on nxix), the 65Bhas 2 80 mm fans in the front, the one in the pic has 1 120 MM fan in the front..

if i had to guess, the one in the pic is a 60BplusII
 
So other then the fan config,and one extra 3.5" drive bay on the front of the(NCIX) case's,are they pretty much the same otherwise ?
 
Slight update to mine, although the inside is a mess, hence no window yet.

Cathodes will likly be moved once i clean up the inside and get a window, but here it is for now...
100_1045.jpg


100_1044.jpg


100_1015.jpg


100_1008.jpg
 
Very nice.
I like that case a lot. I have a A05 myself, but this would definitely by my next choice.
 
Here is mine, pics are not that good cause I was in a hurry. Will try to get some better ones later.


S6300959.jpg


S6300958.jpg


S6300964.jpg


S6300966.jpg
 
Holy sh!t that's sexy!!! I love the diamond plate. It has a great industrial look to it while retaining it's sexy shiny-ness. :cool:
 
Ok, never posted on this thread for some reason, even tho' I check it often. Anyways, he's mine.

3 months ago:
case_1(thum).jpg


Now:
case_2(thum).jpg
 
Ok, never posted on this thread for some reason, even tho' I check it often. Anyways, he's mine.

3 months ago:
case_1(thum).jpg


Now:
case_2(thum).jpg

Very nice. How'd you paint the interior? I've been wanting to paint my PC7B black on the interior as well. You should try and route those SATA cables behind the MB or something. Clean it up a bit. All in all it looks real nice
 
I could not even fathom painting the interior of a Lian Li! That aluminum just looks so nice, but to each his own.
 
Nice looking case...very clean. Here's a few of my build I started a few days ago. Waiting on a few things to finish it out. This is the PC 60B Plus II case btw.





 
more cable management and that case would look sick!


Yeah....I'm going to move some cables around once all the components are in there. Probably going to move those sata cables on the other side of the Hdd cage and hide some behind the mobo tray. Just put some preliminary pics up for critique. Thanks for the compliment though. :D
 
Here is my A08:

A look at the inside
bild057rb7.jpg


The Front
bild054rt5.jpg


The silver panel will be replaced with the black panel of the 7S.

I´ll post more pics, when the case is "finished". ;)
 
@ burnoutmalle:

Hey can you post some more pics of the outside of the case? I think a friend of mine just ordered that case.

Thanks!
 
Very nice. How'd you paint the interior? I've been wanting to paint my PC7B black on the interior as well. You should try and route those SATA cables behind the MB or something. Clean it up a bit. All in all it looks real nice
Thanks dude. Well, I just typed quite a guide that took me about 3 hours and sent it to you, so check your Private Messages Now.
And about the cable management, well, I was actually thinking on buying smaller cables and replace them, since that's the only way I know how to. But people do hide them my making a hole in their case or something. I really don't know. Maybe you guys should help me out in that. I'll record a video and upload it here.

UPDATE: Here's the video: Cable Mess - 28.9MB [Right Click to Save]
 
Thanks dude. Well, I just typed quite a guide that took me about 3 hours and sent it to you, so check your Private Messages Now.
And about the cable management, well, I was actually thinking on buying smaller cables and replace them, since that's the only way I know how to. But people do hide them my making a hole in their case or something. I really don't know. Maybe you guys should help me out in that. I'll record a video and upload it here.

UPDATE: Here's the video: Cable Mess - 28.9MB [Right Click to Save]

Shakey cam FTL! :eek:

haha...j/k

Anyways with regards to your cable mess, first off you need to use some zip ties...those are your best friend.

For the SATA cables...one option is to use some black SATA cables as opposed to those orange cables. Also, you can try to do what I did to my cables:

892074597_560d05c3db_b.jpg


With you case you can try to "fold" down the cables for the HDD and zip tie them together so that they are running uniform (same for the drive power cables.) Another option is to bend the SATA cables underneath the HDDs and tip tie the excess stuff behind that drive carriage.

Don't be afraid to bend cables around (to a certain extent).

Another thing you can get is some heat shrink (just get the basic stuff) & mesh sleeving to hide the internal USB cables, the case-to-motherboard connectors, fan cables, etc.

You can see an example in my case at the top...I sleeved the top USB/Firewire cables the same way (and have been doing it for a while.) It's pretty easy too...Oh and that website I linked to has pretty good prices as well. I've ordered from them multiple times without any problems.

So there you go...that's how I went about doing it with my current system.
 
Nice looking Rigs guys. I'm definitely going to have to get some serious cable management going on in my case so I won't be embarrassed by you pros. :)
 
Here's my new rig with my first attempt at cable management. I would love to go to liquid but the funds are a bit low ATM :)

05-new_pc.jpg

06-new_pc.jpg

09-new_pc.jpg

10-new_pc.jpg

12-new_pc.jpg

15-new_pc.jpg

17-new_pc.jpg

19-new_pc.jpg

20-new_pc.jpg


Specs:
Lian Li PC-V2000B PLUS II
EVGA nForce 680i SLI
Intel Core 2 Duo E6700 2.67GHz
Corsair 2GB DDR2-800
EVGA 8800GTS 640MB GDDR3
Corsair 620W Power Supply
WDC Raptor 36GB (RAID 0)
WDC Raptor 36GB (RAID 0)
WDC Raptor 150GB
WDC Raptor 36GB
WDC 500GB 7200RPM
WDC 300GB 7200RPM
 
Back
Top