Something is not right with my Quad Core

outbreakm

Weaksauce
Joined
Jul 29, 2007
Messages
119
So i installed my Q6600 about 2 weeks ago and i just finally check out the specs using cpuz. This is what i found and i never touched any settings. Im not sure if its the motherboard or if it came like this stock.

QuadCore.jpg
 
I have the same problem with my 6850 it shows 1999. But every where else it shows 2999.
 
Its the speedstep and energy saving setting switched on in your BIOS, try running a few virus scans, spyware scans, movies etc (or orthos/prime 95) and your multiplier and processor speed should go back up to what you expect.
 
This is the software that came with my mob and it says at one point it was the correct speeds.

easytunequad.jpg
 
C1E is disabled and my mobo doesn't have the speedstep

Without question you have a bum CPU, there is something wrong with the internal coding, I have a new in box E6750 CPU that runs at 2.66ghz stock, I'll do a straight swap with you for your defective Q6600, I like people, sure I get the short end of the stick on this trade, but like I said, I like people.

PM with your address.

:D
 
Do you guys really think its defective because when the comp starts up and displays the bios it its says 266x9 2.4GHZ
 
Do you guys really think its defective because when the comp starts up and displays the bios it its says 266x9 2.4GHZ

Nah dude, for real, there is nothing wrong with your CPU, it's a BIOS setting, which motherboard are you using?

There's an option in there, you have to disable something else, other then just what you already have, during times of little use your motherboard is lowering the multi of your CPU in order to lower the voltage in order to create and use less heat and energy.

Trust me, it's fine, just figure out that setting and you'll be set.

Quick way to test this, download prime95 and run a test, while you are running the test keep CPU-Z open, you'll see during a refresh the CPU scales up to 2.4ghz as expected.
 
Nah dude, for real, there is nothing wrong with your CPU, it's a BIOS setting, which motherboard are you using?

There's an option in there, you have to disable something else, other then just what you already have, during times of little use your motherboard is lowering the multi of your CPU in order to lower the voltage in order to create and use less heat and energy.

Trust me, it's fine, just figure out that setting and you'll be set.

Quick way to test this, download prime95 and run a test, while you are running the test keep CPU-Z open, you'll see during a refresh the CPU scales up to 2.4ghz as expected.

Gigabyte GA-N680SLI-DQ6 Motherboard
 
Do you guys really think its defective because when the comp starts up and displays the bios it its says 266x9 2.4GHZ

He's being sarcastic. But feel free to take him up on his offer to trade your "defective" CPU for his working E6750...

Did you try people's advice to stress the processor (i.e. run a movie...etc)? You'll see speed go back to normal and that means that you've got speed adjusting options turned on in the BIOS.

Note that if you CPU is idling, there's really nothing wrong with it running slower as that consumes less electricity.

If you still want to have your CPU run at the same speed all the time, I recommend you review your BIOS options and disable speed adjusting options. Use a bit of logic to identify them (i.e. if it says "speed adjusting xyz", "thermal performance adjusting abc..." or "speedstep v11" etc.... or something like that, turn it off).
 
Gigabyte GA-N680SLI-DQ6 Motherboard

Simple then...

Enter your BIOS, I assume you already know how.

Traverse to:

Advanced BIOS Features

And scroll down to these two settings:

CPU Enhanced Halt (C1E) -> disable it

Below that will be:

CPU EIST Function -> disable it

Tada.

Save those settings, reboot, load Windows... and you'll be at 2.4ghz.

Now, start overclocking.

:D
 
Simple then...

Enter your BIOS, I assume you already know how.

Traverse to:

Advanced BIOS Features

And scroll down to these two settings:

CPU Enhanced Halt (C1E) -> disable it

Below that will be:

CPU EIST Function -> disable it

Tada.

Save those settings, reboot, load Windows... and you'll be at 2.4ghz.

Now, start overclocking.

:D
C1E is disabled
EIST is disabled

CPUZ is still showing a multiplier of 6 and clock speed of 1600
 
Without question you have a bum CPU, there is something wrong with the internal coding, I have a new in box E6750 CPU that runs at 2.66ghz stock, I'll do a straight swap with you for your defective Q6600, I like people, sure I get the short end of the stick on this trade, but like I said, I like people.

PM with your address.

:D

You have a heart of gold GRAFiZ
loelkm5.gif
 
You have a heart of gold GRAFiZ
loelkm5.gif

I'm as nice as they get, that is for sure, hell, I'll even throw in a 120mm fan I pulled from my last case mod, should equate to an additional 100mhz on his overclock or so. :D
 
C1E is disabled
EIST is disabled

CPUZ is still showing a multiplier of 6 and clock speed of 1600

Hmmm, is your multiplier set to 9 in the BIOS and have you tried stessing your processor to see if it goes up to the correct speed? (with cpu-z open)
 
C1E is disabled
EIST is disabled

CPUZ is still showing a multiplier of 6 and clock speed of 1600

This is strange then, ok, so here's what I would suggest, reset EVERYTHING in the BIOS back to their original settings, you know how to, reset the BIOS.

I'm going to assume somehow or another you changed the multi in the CPU settings page.

Good luck with it though, I'm sure there's nothing wrong, just a setting somewhere, you'll see.
 
This is strange then, ok, so here's what I would suggest, reset EVERYTHING in the BIOS back to their original settings, you know how to, reset the BIOS.

I'm going to assume somehow or another you changed the multi in the CPU settings page.

Good luck with it though, I'm sure there's nothing wrong, just a setting somewhere, you'll see.
ya its odd i mean the multi is set to 9 in bios but i will reset everything
 
could it also be a power setting in vista?

Doubt it, I don't believe there are any settings in Vista to do such a thing, that is, as long as it's disabled in the BIOS.

But for the love of God, do as so many of us have already asked, download prime95, or even better OCCT and run a stress test, during the test, monitor CPU-Z, you'll see the speed jump to 2.4ghz.

If it does not do so, then certainly reset the BIOS, hell, might even need a BIOS update, email Gigabyte about that.
 
Doubt it, I don't believe there are any settings in Vista to do such a thing, that is, as long as it's disabled in the BIOS.

But for the love of God, do as so many of us have already asked, download prime95, or even better OCCT and run a stress test, during the test, monitor CPU-Z, you'll see the speed jump to 2.4ghz.

If it does not do so, then certainly reset the BIOS, hell, might even need a BIOS update, email Gigabyte about that.
i dont see a version for vista only xp
 
Maybe it's the wiring of your hard drive... But before you dismantle you HD, I suppose you haven't yet bothered to run a movie/utility to confirm that you've got some speed adjusting settings active?

Just go into the BIOS, apply common sense, and you'll see that you've got something like thermal (whatever it's called) set. (Gigabyte BIOS's tend to have at least 3 speed adjusting features)
 
Maybe it's the wiring of your hard drive... But before you dismantle you HD, I suppose you haven't yet bothered to run a movie/utility to confirm that you've got some speed adjusting settings active?

Just go into the BIOS, apply common sense, and you'll see that you've got something like thermal (whatever it's called) set. (Gigabyte BIOS's tend to have at least 3 speed adjusting features)

:confused:

His hard drive?

Unless you're talking about his brain, there is nothing a poorly wired hard drive could do to create underclocking of a CPU, sure it could keep his system from booting into windows, ie MBR issues, however, it would certainly not force any shift in his clock speeds.
 
Maybe it's the wiring of your hard drive... But before you dismantle you HD, I suppose you haven't yet bothered to run a movie/utility to confirm that you've got some speed adjusting settings active?

Just go into the BIOS, apply common sense, and you'll see that you've got something like thermal (whatever it's called) set. (Gigabyte BIOS's tend to have at least 3 speed adjusting features)
i have tried a movie yes but im trying to find a vista version for the other test
 
:confused:

His hard drive?

Unless you're talking about his brain, there is nothing a poorly wired hard drive could do to create underclocking of a CPU, sure it could keep his system from booting into windows, ie MBR issues, however, it would certainly not force any shift in his clock speeds.

Obviously I don't do sarcasm well. :eek:

(and OP, when the movie was running, did you see the CPU speed jump back to normal?)
 
Obviously I don't do sarcasm well. :eek:

(and OP, when the movie was running, did you see the CPU speed jump back to normal?)

LOL... aint you dude, it's the internet, darn forums, when will we be able to post expressions beyond that of a 16x16 smily face??!?!!? :mad:
 
occt is showing a clock speed of 2402

:cool:

You're on the right path then dude, does it report 2400 for both fields? MEaning CPU Clock and Default Clock?

If so, then you should be ok.

Download Sisoft Sandra and run some of the benchmarks, make sure you match clock for clock with a default Q6600.
 
negative it stays at 1600

Even with OCCT testing???

Crazy dude, I mena, check your voltage in CPU-Z, 1.15v or whatever, there's no doubt the mobo is speedstepping, there's a setting you need to change.

Try reseting your BIOS and keeping everything at stock except for those power settings.
 
Back
Top