x gene water cooling options

Do you have room for a small 120mm intake radiator? Maybe another 80mm radiator somewhere else?

Put some internal shots up, with everything else installed.
 
lol thats wat i was thinking! here some pics

Picture011.jpg

thats the lower section
Picture017.jpg

thats the top section where the 80 rad would go, i would just cut out those ventilation holes:D
Picture020.jpg

shit i guess if i get a 120 rad i will have to take out the hdd cage and use the 3.5 bay.

if u need more pics to noe anything just tell me. and where would the res go? i was thinking one of those long cylinder ones right in front of the mobo, or an external one maybe?
 
Will you be running your GPU on water too?

It does look like you'll have to take out the 5.25" bay... as it goes infront of the 120mm intake...

Picture011.jpg


How much room is there in the area marked with the green square? Between the metal piece and the 120mm fan... I'm guessing not much...
 
wow nice!! and yes the vid card will be on water too. and there is like no room between the fan and the metal, i use the space to hold my wires from gettin into the fan. but yes that does look nice!
 
wow nice!! and yes the vid card will be on water too. and there is like no room between the fan and the metal, i use the space to hold my wires from gettin into the fan. but yes that does look nice!

No room eh... It'll be tough to mount the radiator there... You might have to remove that metal piece to get it to fit...

I can upload some shots of how a single radiator looks on a 120mm fan if you'd like. You can judge if it'll fit.
 
A single 120mm radiator would be enough to survive on, but it'd be nice to have a little more capacity. Have you thought about a 2x80mm radiator on the back? They aren't the greatest (not quite the cooling power of a single 120mm), but with a 2x80 and a 120mm rad, you'd be able to get a lot more stable load temps. (nvm - I missed the part where you were contemplating an 80mm rad somewhere.)

Also, why run an external reservoir? I'd use a T-line in a SFF any day of the week. If you really want a res, a Swiftech micro res can often be squeezed in internally - even in a SFF.

If you don't mind doing a little more cutting, why not put a 240mm rad on the right side of the case? If anything, it'd have to be a BI Stealth due to clearance issues. I'm getting a ballpark estimation of ~1" clearance + the thickness of the case wall. Not much, but maybe just enough for a Stealth. There wouldn't be room for fans on the rad in an internal build, but you could just make all the other fans in the case exhaust. Then just put a filter mesh and an AC Ryan grill on the outside, and it'd look damn spiffy. With 2x80mm exhaust fans on the back, and a 120mm exhaust on the front, (I guess the PSU also exhausts too, and it looks like you've got a couple other 80mm fan mounts on the upper deck too) you'd be okay to run the rad without fans mounted directly on it - as long as you seal the rest of the case so that the rad is the only place air can get sucked in.

As long as every fan is on exhaust, you should have enough suction that you won't need fans directly on the rad. If you don't like relying on case suction, you could even mount 3x80mm fans on the 240mm rad so that the top 2/3 of it get forced airflow. You'd need to leave the bottom part naked to clear the motherboard, but it'd still be 100x (well actually 2x) better than a single 120mm radiator cooling that loop - and a lot less pressure drop than a 120mm + 80mm setup. (Not to mention a hell of a lot more cooling capacity.)
 
well nonlnear that 240 rad is an awsome idea but those side panels are all on piece and is very flimsy, so thats a big no, but very good idea but wat about putting a 240 in the front and make a new front panel from scratch so the 120mm fans llok like they would be built in?

watercoolingoptions1.jpg

watercoolingoptions2.jpg

watercoolingoptions3.jpg

watercoolingoption4.jpg
 
If you want to go with the front panel mounting position for a 240 radiator, you'll make your life a lot simpler in a way, and a little more complicated in another.

First, there's actually room for a deeper rad in the front position. You aren't forced to use a stealth. You may still want to if you need the room for fans in the pull position.

I firmly believe that with thorough planning, you can put a decent WC system fully internal into all but the tightest cases. You've just got to be veeeery careful. Now, how much space is there between the front panel and the front of the motherboard (or anything else that's not removable)? Does the case's facade attach right onto the front of the frame, or is there an extra gap in front of the frame? I'm thinking about extracting every mm of depth inside the case. I like the idea of cutting one big hole in the front, and just mounting an AC Ryan grill liek this or this. (The "stripes" is less restrictive of course, but on the front panel looks matter, so that's your call.) With a good mesh filter behind that, you won't have to worry too much about finishing work, as that's all prefabbed. Just cut your hole, and worry about good mountings for everything. (I'm no good at making cuts look nice, so I appreciate these grills for their ability to make anyone's work look good for a reasonable price.)

If you've got enough room to mount a rad and fans between the motherboard and the front wall, it's a no brainer in my books. It improves the airflow for the entire case, and gives you a very clean routing strategy for the loop, with a lot more cooling capacity than a 120 or a 120+80 setup (and cheaper than a 120+80 as well).

Now, the one downside to putting the rad up front is you lose the simple floor option for pump placement. I 'd propose mounting an MCP355 sideways on the inside of the right case wall. If the case wall is too flimsy, you might have to improvise a bracket to mount it on.

I'll try to whip up a drawing soon, but here's the concept: The basic idea is that the pump is on its side, with its bottom facing the right case wall. It is near the back of the case, as high as it can be in the lower compartment, and as far back as possible. Hopefully so that the centerline of the pump motor is behind the CPU block's barbs. The pump's barbs face forward, with the outlet on top, and the inlet on the bottom. (If you're running an aftermarket top, like petra's, the inlet would be... pointing almost directly at - but slightly offset from - the video card block's barbs -hint hint :) ) Angle the pump slightly downwards, so that the outlet points at the bottom barb on the radiator. That way it's a gentle bend from pump to rad. Also the outlet from the rad is on top, giving you a reasonable arc to the CPU block. Run the CPU --> GPU, and GPU --> T-line/res --> pump inlet (This becomes a nicer path with petra's top, but it's livable without it. If you really want a res, it's not hard to rout tubing from the GPU to a res in one of the top cavities, and then to the pump. (If you are running the pump stock, that might work out better than trying to route with a T-line.)

Personally, I'd go with Petra's top and a T-line in the layout above. With a T-line in the run from GPU to pump, you can easily position it so that it comes up through the floor of the upper compartment. Then you can have a loop of slack that gets coiled up when the case is closed. To open it up, remove the case, hold the coil of slack so that it'll feed through the hole, and then lift the drive cage. I would personally not drill the fillport into the case, but just leave it internal. I don't really get why people bother "mounting" the fillport. I find it more versatile for filling and draining if it's free. I think people just mount fillports so that it's more obvious from all directions that they have a watercooled rig - not that there's anything wrong with that.
 
so like wat parts would i need, like the specific parts, that would fit and perform well
What video card do you have, and what's your budget? I'm getting ballpark $260 for decent parts (TDX,Maze5, DDC+,BIP240, 10' Masterkleer, fittings, etc.), and about $300 for top notch parts (DDC w/petra's top, Fuzion, MCW60, etc.), and $350 for top notch parts including an EK full cover GPU block. (I don't think you have room for a PA120.2, but if you do and have the $$$, it'd be a great option for the "top end" build.)

Those are all "regular" prices. If you shop carefully, and with a little luck, you could probably knock $50 or more off of any one of those estimates - especially if you aren't super finicky about which parts you get. For example, AquaXtreme has some decent CPU blocks that are great values, etc. And scour every site for sale/clearance prices.


If I had to guess, I'd say you don't have a hope in hell of cramming that beast into your case, and it probably wouldn't make you happy even if you could. I could only find a few reviews out there, and I think they were all manufacturer provided samples. They all compared the CoolIT products to air cooling (not to good watercooling...) For a quick check on what to expect, look at the load temps about halfway down this page. Basically the load temps with the CoolIT products aren't much better than stock, and are not necessarily any better than good air cooling. Notice the CoolIT Eliminator failed the overclocked load test in silent mode. (The stock cooler failed to post a result in their overclocked load test as well.) Basically if you're going to be overclocking, the Eliminator will be quite loud - if you can even cram it into your case.

Now, I don't think the CoolIT Eliminator is a bad product. I actually think it's got a lot of potential - especially at its pricepoint. I'm a little suspicious of the numbers that CoolIT is claiming, as the load temps in reviews are what really matter, and they don't look all that impressive. Also, the independent testing that CoolIT refers to on their site looks liek they compared themselves to soem pretty crappy brandname watercooling kits - but they won't tell you which ones. :rolleyes: With a little elbow grease, they could turn these products into winners though. That said, it's not going to fit in your case, and it's not going to take care of your GPU either - unless you get two!
 
ok cool, i have a x800xl agp card, and im drawlin up a plan right now, i want one of those petra's with the tube fitters point to the wall and not up, they will fit in my case. and the front panel has no room because it has a part that sticks out and on the bottom its a different size, and from the front of the case to the mobo is 3.5 inches
 
ok cool, i have a x800xl agp card, and im drawlin up a plan right now, i want one of those petra's with the tube fitters point to the wall and not up, they will fit in my case. and the front panel has no room because it has a part that sticks out and on the bottom its a different size, and from the front of the case to the mobo is 3.5 inches

I'm not sure what you are saying here about "the tube fitters point to the wall and not up". Did you understand what I was saying about the pump position? I'll have a drawing tomorrow. It's late...

Also, are you saying that mounting a 240mm rad in the front will not work? What part is in the way? Pics? I believe you, but I'd really just like as much information about the case as possible. Possibly a picture of the front case panel from behind (from the inside of the case). Maybe even with the 120mm fan removed.

3.5" is plenty of depth for a radiator and fans. You might not even have to do too much cutting to pull it off...
 
ok heres the problem
56.jpg
,
88.jpg

and heres an option, if the stealth 240mm rad is as skinny as a 120mm fan than i can put the rad either were the pink is circled or were the fan is now, and is the fan is in the case then i can put the 2 fans on the out side, take off the front panel and use the a.c. ryan radgrill over the fans, or are the rads suppose to be on the out side and the fans on the inside? and for the pump, i cant put it on the panel cus if i wanna open up the case the pump will be moved with the panel, can i put the pump on the floor infront of the rad?

and about the vid card block i want one like this, http://www.frozencpu.com/products/5...idia_8800_GTS_501254.html?tl=g30c87s145#blank, were the tubes connect to it they have to be like that.
 
The pump:

What I was saying is, I would get a piece of steel plate from your hardware store, and make a bracket that is shaped like this " ] " that goes just inside the right case wall. It would be connected to the bottom of the case, and the beam that runs from the front to the back on the right side. You can either glue it in place, or rivet it. Whatever you find easiest. The pump will be mounted to this bracket - not to the case wall.

The radiator:
The radiator sits behind the inner case wall (the wall that your 120mm fan is currently mounted to. You cut almost all of that wall out to let air pass through to the radiator, and you drill new holes - where you want them - so that the radiator has enough clearance on the left side of the case. (I don't think the current fan holes will work, because most radiators extend past where a 120mm fan does.

Fans:
The fans are then attached to the radiator. They go behind the radiator. They are inside the case, between the radiator and the motherboard; they do not extend through the front panel of the case (nothing does).

AC Ryan grill:
You cut a hole in the front case panel according to the template for the 240mm AC Ryan grill. Then you mount the grill to the front case panel. The grill is NOT directly connected to the radiator or the fans. (You can mount filters either directly onto the radiator, or onto the back of the front case panel. I'd probably put them on the radiator, as there's probably some air leakage through the gap around the front case panel.)

Video card:
Do you mean this card? (Don't worry about the brand - just the processor.) If so, there is no full coverage waterblock for it. It doesn't need active RAM cooling, and it really wouldn't be worth it anyways. This is good news. That means you can make do with a plain old MCW60 (saving you about $50) without RAMsinks (saving you another $10-$15). And you can even use that MCW60 on the next video card you buy. The fancy full coverage blocks are pretty much all model specific - and thus are tossed in the trash (or resold on the forums for pennies on the dollar - if you're lucky) when you upgrade your card. Using a plain GPU block does make your tube routing slightly harder, but you could just use elbows if you need to. An elbow fitting can't be any worse than the 90 degree turn that the flow takes going into/out of the full coverage blocks anyways.
 
o ok wow thanks!! imma cut into the peice of metal that connects to the top section were it touches the fan, so just like a notch out of it. then put that pump like you said, but do i need to weld it or just screw it?

now the rad part is weird, so i have to put that a.c. ryan grill on my front panel after i cut into it? and then mount the rad then the fans?

and were does the res go? and wat pump and cpu block should i get, i was think of a swiftech apologee gt?. and nothing can go on the upper deck.
 
o ok wow thanks!! imma cut into the peice of metal that connects to the top section were it touches the fan, so just like a notch out of it. then put that pump like you said, but do i need to weld it or just screw it?
You shouldn't need to weld it. It's probably easiest to use short sheet-metal screws. If you have a riveting tool, that'd be easy and cheap, but it's not really worth picking up a tool just for this job. You could use some good metal glue, but screws are probably better.

now the rad part is weird, so i have to put that a.c. ryan grill on my front panel after i cut into it? and then mount the rad then the fans?

The entire paragraph below is talking about the internal case - NOT the nice black case exterior/front panel.

The rad sits inside your case basically where your 120mm fan is sitting right now. It won't line up with the holes that your fan is mounted to, because of the problem area that's been highlighted already. That's fine. Once you get your radiator, you just want to pop out your 120mm fan, and sit the radiator in there as far to the left as it'll go. When it's in position, figure out what part of the front wall you have to cut out to free the airflow. Then cut out tat whole area. (The hole for your 120mm fan should be a large part of it.) Make sure to leave enough metal so that there's room to drill all 8 mounting holes for the radiator to the case frame.

and were does the res go?
I think it's easiest to build your loop without a reservoir. I'm at a loss right now for a good res location - especially if the upper deck is off limits.

edit: if you really want a res, we can work one in. If you push the pump as far back in the case as possible, and as low as possible, then putting a Swiftech Micro-res on the same side near the front would make good sense. The res barbs would face the pump barbs, making it easy to get from the res to the pump inlet. The tubeing layout works pretty cleanly as long as you can run tubes over the top of the cards. (This might require the use of elbow fittings, but it should be possible, even if it's a tight fit.)
and wat pump and cpu block should i get, i was think of a swiftech apologee gt?. and nothing can go on the upper deck.
Now, if you could have used a full cover GPU block, then the DDC with Petras top would have made your tube routing absolutely beautiful. The bad news is, that beautiful routing is not an option. The good news is, you might get to save almost $100.

Now, how much room is there above your PCI/AGP card when the case is assembled? Is it <1", 1" - 2", or more than 2"? (It looks like it's < 0.5") Once I know that, I can give you an idea of how to run your tubing, and what parts to get. (It makes a difference whether or not you'll be getting Petra's top or not. If you can't run tubes over the top of your AGP card, there's no point getting Petra's top for your loop - saving you ~$30. Also, that would mean it'd be easiest to run 3/8" ID tubing instead of 7/16" tubing, because you'd be using the stock barbs on the DDC pump.)

I'll be back tomorrow. Gotta get some sleep tonight... I hope we'll have a decent loop spec'ed out for you by tomorrow. Just to be clear - getting this loop into that case is going to take some fairly serious case modding: you'll be installing a custom pump mount, cutting the front of the case frame, and the front case panel. Not to mention lots of fiddling to get things to fit just right.
 
nice ok, so no res? i was thinking maybe where the two rear 80mm fans are, internally or externally? and i found everything i want/need and it came shy of 300 bucks, so ya dam! this might take a while just to get enough money, but i am going to do it! ok i will talk to you tomorrow.
 
You should be able to so it for around $260-ish. If money's tight, don't order in a hurry. You can probably do better than $300 - even if you want high end parts. More later...
 
it'll take some modding but you can do it. I wish I had mine on me right now and I could give you some great estimates...sadly, it is still at the lab.
 
Do you have cooling devices for all your video card's RAM currently? I can't quite tell from the pics (remember there's RAM on the back of the card too). If you don't have it now, you won't need it after you watercool it, unless you plan on trying to push the GPU's memory clock further. (Although I'd wonder why you'd try for a further overclock now that it's not a cutting edge GPU anymore. One or two years ago, I'd understand.) Remember the GPU RAM is still going to get plenty of airflow, because the radiator fans will blow a nice breeze straight back over the whole motherboard.

If you really want ramsinks for the video card, you can work them in, but if you don't want to bother, you can save about $20 from the total build cost.
 
no i dont have ramsinks for my vid card, and ya its a good idea not to get them, the vid card cant be pushed that much more than it is. so i dont need them
 
One other option I'm contemplating for this build is an X-flow style radiator. Now, these aren't really very fashionable, because they don't have any real performance advantage (there's a raging debate :rolleyes:, but basically it's little to no difference in performance), and they're a bit taller because they have a tall tank on each end - to give room for a barb on each end. For most people, this just means they take up more room with little benefit. However, for a SFF build like yours, it will save you a lot of tube length, leading to a much cleaner layout. You'll save about a foot of tubing, because you're cutting out almost a full run across the width of the case. It will also make for less tube clutter on the right side of the case; it'll be easier to get at your RAM, and other goodies on the motherboard. A minor issue, but worth thinking about nonetheless.

It would cost about $15 more; because a BIP2 is $34 (a decent radiator, and cheaper than the MCR220), and a BI Stealth X-flow runs about $50.

No matter which radiator you go with, I'd also recommend mixing tube diameters. It's kind of unusual, but here's why:

1. When you reuse these parts, odds are you'll want to run a full 1/2" system.
2. The MCP355 pump has 3/8" barbs, and you won't be using an aftermarket top. You either use 2/8" tubing runs in and out of your pump, or you need adapter fittings. (Adapter fittings will make the build look messy, and make routing harder - because they don't flex.)
3. There is no added cost compared to a full 1/2" system. Two 3/8" barbs costs about the same as two 3/8" - 1/2" adapter fittings. edit: actually the MCW60 ships with both sizes of barbs, so you'll only need to buy 1 extra barb for the radiator.
4. There is no reason not to. Just because some parts of your loop are 3/8" doesn't mean the rest have to be too. The advantage is almost completely negligible, but there is no disadvantage compared to a full 3/8" loop, as long as you don't have any super tight turns that only 3/8" tubing could make (but if that were the case, you could just use an elbow).

What you'll end up doing is ordering your blocks and radiator with 1/2" barbs, and order one 3/8" radiator barb, and one 3/8" barb for the block that goes right before your pump in your loop order. (If you get an X-flow, it'll be cleanest to run pump -> rad -> GPU -> CPU -> pump; with a BIP2 or MCR220, it'll be best to run pump -> rad -> CPU -> GPU -> pump; I didn't mention the T-line, but it's in there somewhere.)

Down the road when you build your next system, all you'll have to do is order a pump top with 1/2" barbs, and swap out the two 3/8" barbs from the rad and MCW60, and you'll be ready to run a complete 1/2" system.
 
i was looking at the bi stealth ones, but i dont think my case will have enough room for the tanks. and no res? yes u did mention a t line, but wat is it? is it where theres an extra tube sticking up, and thats were u refill the water? ok imma say that i have to use 3/8 when i go cpu>gpu and gpu>t-line>pump because there is only a little bit of room above the vid card, and then , 1/2 from pump> rad>cpu. does that sound right?
 
How wide is the inside of your case? What's the absolute widest radiator you could fit in there?

(An X-flow needs 292mm.)
 
i was looking at the bi stealth ones, but i dont think my case will have enough room for the tanks. and no res? yes u did mention a t line, but wat is it? is it where theres an extra tube sticking up, and thats were u refill the water?

Just do a forum search for "t-line" or look through the gallery thread. There's lots of pics.

ok imma say that i have to use 3/8 when i go cpu>gpu and gpu>t-line>pump because there is only a little bit of room above the vid card, and then , 1/2 from pump> rad>cpu. does that sound right?

It'll be 1/2" everywhere except GPU -> pump, and pump -> radiator.

If you mix diameters, you'll want to put the T-line in one of the 1/2" sections because the Dangerden fillports only come in 1/2" AFAIK. It's not as big a deal as most people say. As long as you can flood the pump from the T-line before turning the pump on, everything will be fine.
 
it is 292mm but there are support bars and stuff that are in the way

Do you mean the two bars that run front to back on the right and left? Or are there other little bits near the front of the case that would interfere?
 
ok so i put a t line in between the rad and cpu?

and how do yo flood the pump?, and how will i drain the whole thing?
 
ok so i put a t line in between the rad and cpu?

and how do yo flood the pump?, and how will i drain the whole thing?
Let's worry about all that after we figure out what radiator will work best. It'll all work out fine.

Now, what is the distance between the inside of each of the beams that run from the front to the back (the ones on the right and left sides of the case)? And how high off the case floor are they? To be precise: how much space is there between the case floor and the [/i]bottom[/i] of each of these beams?
 
well the bars are 10 inches apart. so imm going to have to cut into them. and then the left bar is 2 1/4 inches off the ground and the right one is 4 1/8 off the ground.
 
well the bars are 10 inches apart. so imm going to have to cut into them. and then the left bar is 2 1/4 inches off the ground and the right one is 4 1/8 off the ground.

So an X-flow is definitely not an option then. Forget everything I said about that.

How exact are those measurements? If you could give again as precisely as possible, it'll help a lot. (In inches and mm, please - manufacturers' specs are sometimes mixed.)

A Black Ice radiator will be 277mm wide. The Swiftech MCR220 is wider at 284mm. How wide is the case's exterior? And how thick are the side panels (in mm if possible)?

Now, I'm thinking you might be able to use the unique shape of the MCR220's tanks to your advantage. Even though it's a little wider than the Black Ice rads, it may actually be a little easier to squeeze in there. If the radiator is mounted with the barbs on the left side, the bar on the left will sit inside the indentation between the two tanks. It won't be perfectly centered (it would be nicer if it were 2 1/2" off the floor), but it will help a little bit. It looks like you'll be able to save at least 0.5", and maybe close to 1" of width by having the tanks straddle the bar like that. The process of coaxing these parts into that case is a game of millimeters. Every one counts. If you can get a full inch from the straddle position, that might be enough - assuming (optimistically) that there's a hair more than 10" between the two bars.
 
ok, the out side is 292.1mm, between the bars is 266.7mm. and i think the MCR220 might work cus i can cut into the bar so it would cradle the indention of the tank. and sorry between the bars is 10.5 inches.
 
ok, the out side is 292.1mm

So that means there really is enough room for an MCR220. There probably wasn't enough room for an X-flow even if there were no bars. It'd be snug if it fit at all.

between the bars is 266.7mm. and i think the MCR220 might work cus i can cut into the bar so it would cradle the indention of the tank. and sorry between the bars is 10.5 inches.

Sounds like an MCR220 is going to require the least amount of cutting. You might not have to cut at all, or just a little bit of notching into the lower bar could be enough. The less you cut into those bars, the more rigid your case will be when all is said and done.

Now, with this radiator orientation, it makes more sense IMHO to mount the pump on the left side so that it pumps straight into the radiator. I'd run a DDC with Petra's top (so everything is 1/2" now) sitting so that the inlet barb points parallel with the front edge of the motherboard.

A route laid out like this:
pump -> rad -> GPU -> CPU -> T-line/res -> pump
will give you a good layout with no tight turns. That's with the GPU block mounted so the barbs point to the front of the case. (I think trying to run tubing over the top of the card is begging for problems with your tight space constraint.)

You could even use a reservoir if you prefer. Just mount it anywhere on the inside of the right case wall the same way you were going to mount the pump - but near the front of the case, with the res. barbs pointing backwards to the CPU block. That whole wall is just sitting there waiting to be used... A Swiftech micro-res costs about the same as T-line and fillport anyways. I was pushing for a T-line earlier because with the pump on the right side of the case, there wasn't really a good location. Now there is. :)

Here's a shopping list:

Petra's:
64.99 - D-Tek Fuzion
4.90 - 10' of 7/16" Masterkleer tubing
41.99 - MCW60 with no ramsinks
44.99 - MCR220
28.95 - Pump top with 1/2" DD barbs (Petra is OOS on the pump/top combo)
---------------------------------------------------------------------------------
185.82 + S/H

Jab-tech.com:
16.95 - Swiftech Mc-res
69.95 - MCP355
7.00 - 2x Yate-Loon D12SL-12 (or 9.00 for 3)
---------------------------------------------------------------------------------
86.90 + S/H

That's a little higher than the $260 I'd said earlier, but this includes Petra's top. I wasn't including that in my $260 ballpark figure.

Those are all top notch parts. Anyone on this forum would be happy with that spec (well except maybe some diehard AC fans :)). Swap in better fans if you want to spend more, but if you don't need lots of airflow, the Yate-Loons will save you a chunk of change. There are better fans out there, but not for less than about 3-5x the price.

There may be better prices on one or two parts, but Petra's got decent prices on everything (esp. the MCW60) and he'll take care of you. He's OOS on the pump, and Jab-Tech has the best price I could find (most places have it for $75 right now). And jab-tech has a better price on the res than Petra. Can't argue with that if you're already ordering something from Jab-Tech that you can combine shipping with. Also, jab-tech has the best price for the fans that I've seen anywhere.




Oh yeah, throw in your additive of choice. Pentosin from Petra seems the soup du jour around here lately. That's another couple bucks.
 
Back
Top