World IPv6 Day June 8th

CommanderFrank

Cat Can't Scratch It
Joined
May 9, 2000
Messages
75,399
This upcoming Wednesday, many of the largest technology companies will make the switch to IPv6 for a 24 hour trial. It is a possibility that the run of the mill Internet surfers will notice nothing different during the testing period, but the large corporations such as Google and Facebook could be seeing some glitches during this phase of early testing.

Already, recently produced routers support IPv6. Windows XP, Vista, 7, and upcoming Windows 8, as well as major Linux distributions including Red Hat and Ubuntu, are IPv6-ready. All ISPs eventually will eventually have to support IPv6 addresses as well.
 
but the large corporations such as Google and Facebook could be seeing some glitches during this phase of early testing.

AFAIK, Google completely switched over to IPv6 a long time ago in their internal networks.
 
We are already doing a small IPv6 test. all of our public facing servers are now doing IPv4 and IPv6, have a few computers outside our firewall using it. So far so good, will be interesting to see how everything goes on June 6

ISPs are going to have the hardest time here as it will be the most expensive for them. A bussiness can suport it on the OS side, just need to change out some switches and routers maybe and they are all set. But for an ISP, all of the CPE must support IPv6 to fully move over, which means all dsl modems will have to be replaced, all wireless broadband will need to be replaced, for FttH the onts at the house will need to be upgraded. Which is a lot of cost there for the companies. Then of course you have the dslams and everything else. Some equipment out in the field never will support IPv6 so they will need to scrap that stuff, other stuff might support it "someday". I know two of the makers have plans for IPv6 to be supported by Q4 2012 / Q1 2013, but that isn't going to do anything right now to help people move over. OS makers were right on this making windows, linux and the rest support IPv6 years ago. Router and Switch makers were a little more behind and even newer equipment doesn't support it. At the telco level they have just now even begin to consider putting it there.
 
Oh boy. I'm a network engineer, and the thought of learning IPv6 hurts my brain.
 
Oh boy. I'm a network engineer, and the thought of learning IPv6 hurts my brain.

And for those who don't know, this is an IPV6 address:

The IPv6 128-bit addresses are represented as a series of eight 16-bit hexadecimal fields separated by colons in the format: x:x:x:x:x:x:x:x. This is an example of an IPv6 address:

2031:0000:130F:0000:0000:09C0:080F:130B
 
We're just gonna dual IP Stack until every the migrations complete. Unfortunately I don't think early versions of windows xp dual stack well and we have 600k subs gonna be some fallout same as we had with the digital change over.
 
Oh boy. I'm a network engineer, and the thought of learning IPv6 hurts my brain.

And for those who don't know, this is an IPV6 address:

The IPv6 128-bit addresses are represented as a series of eight 16-bit hexadecimal fields separated by colons in the format: x:x:x:x:x:x:x:x. This is an example of an IPv6 address:

2031:0000:130F:0000:0000:09C0:080F:130B

I know my was like yeah just add IPv6 /64s to all your access routers. baaaaahh. do not want.
 
Oh boy. I'm a network engineer, and the thought of learning IPv6 hurts my brain.

And for those who don't know, this is an IPV6 address:

The IPv6 128-bit addresses are represented as a series of eight 16-bit hexadecimal fields separated by colons in the format: x:x:x:x:x:x:x:x. This is an example of an IPv6 address:

2031:0000:130F:0000:0000:09C0:080F:130B

2031:0000:130F::9C0:80F:130B

We're just gonna dual IP Stack until every the migrations complete. Unfortunately I don't think early versions of windows xp dual stack well and we have 600k subs gonna be some fallout same as we had with the digital change over.

XP SP3 runs ipv4 and ipv6 together just fine. Doing it on some machines just fine. You can't assign it a static ipv6 address, so you just set everythng up on the router and let it auto assign itself an address.
 
AFAIK, Google completely switched over to IPv6 a long time ago in their internal networks.

I'm studying to become a network engineer, and with CCNA, you spend several months studying IPv4 and then maybe 2 or 3 days on IPv6.

Don't think I'm going to start studying CCNP until after the switch to IPv6. Don't want to spend so much time of my life studying something that is going to become completely irrelevant.
 
I'm studying to become a network engineer, and with CCNA, you spend several months studying IPv4 and then maybe 2 or 3 days on IPv6.

Don't think I'm going to start studying CCNP until after the switch to IPv6. Don't want to spend so much time of my life studying something that is going to become completely irrelevant.

It's not really important that you be a IPv6 expert. It's not gonna help you. IPv6 is just more bits so if you understand 32bit you'll be just fine with 128bit. The reason there's so little of it is because there's not much to add.

Routing still functions exactly same. using OSPF (which will be on your tests A LOT) and BGP to advertize subnets won't be any different. I guarantee you the 2011 and 2012 CCNP tests won't have much more IPv6 that the current tests.

Unless you're somebody like me with a lot of public internet facing address space like a /12 parsed out to a bunch of remote networks it's just not important to know.
 
IPv6 is slightly annoying, but not really all that hard to understand. Whats hard to understand is the mess of 6to4, communicating to 6to4 networks from a native IPv6 network, and vice versa.
 
IPv4 is easy enough to keep in short term memory when I couldn't copy paste it. At least IPv6 will let you shorthand/abbreviate sections with zeros:

2002:0000:0000:0000:0000:0000:0a00:0001 ====> 2002::a00:1

Hopefully in our life time we'll mainly be dealing with zeros.
 
The bottom line is that we are running out of IPv4 IPs the result of that will be that not everyone who wants an IPv4 IP is going to get one.

Likely the respose to this will be to push end users behind ISP level NAT to free up IPs. If you are lucky your ISP may give you IPv6 as well when they do that but I wouldn't bet on it.
 
Many of the servers are "dual stacked", i.e. they support both. Your PC most likely is"dual stacked" as well. But do you use IPv6? Most likely not, because some network component in-between does not support it. There are ways around this problem though,and fascinatingly they work very well against censorship.

There are transition services to help people like you getting connected to IPv6. One of them is called Teredo .

Most current Windows versions have Teredo enabled by default (Vista does, and Windows 7 does as well). With XP SP2 you need to enable it.
First ensure the IPv6 protocol stack is installed on your PC. Just open the network connections, open any interface's propertieswindow and check if the protocol is there; ifnot, install it.
Then open a cmd window (click on Start, then click run in XP and type cmd; with Vista/Windows 7 type "cmd" in the search field, wait until cmd prompt appears, right-click on it and choose "run as administrator"). In it, type this:

netsh interface ipv6 show teredo


If type is "default" and you haven't got IPv6connectivity try this:


netsh interface ipv6 set teredo enterpriseclient
 
The bottom line is that we are running out of IPv4 IPs the result of that will be that not everyone who wants an IPv4 IP is going to get one.

Likely the respose to this will be to push end users behind ISP level NAT to free up IPs. If you are lucky your ISP may give you IPv6 as well when they do that but I wouldn't bet on it.

doesn't work quite like that the IP has to be routable if you just had an IPv6 ip address you can't any where that doesn't advertize IPv6.

Many of the servers are "dual stacked", i.e. they support both. Your PC most likely is"dual stacked" as well. But do you use IPv6? Most likely not, because some network component in-between does not support it. There are ways around this problem though,and fascinatingly they work very well against censorship.

There are transition services to help people like you getting connected to IPv6. One of them is called Teredo .

Most current Windows versions have Teredo enabled by default (Vista does, and Windows 7 does as well). With XP SP2 you need to enable it.
First ensure the IPv6 protocol stack is installed on your PC. Just open the network connections, open any interface's propertieswindow and check if the protocol is there; ifnot, install it.
Then open a cmd window (click on Start, then click run in XP and type cmd; with Vista/Windows 7 type "cmd" in the search field, wait until cmd prompt appears, right-click on it and choose "run as administrator"). In it, type this:

netsh interface ipv6 show teredo


If type is "default" and you haven't got IPv6connectivity try this:


netsh interface ipv6 set teredo enterpriseclient


^This is what is gonna basically have to happen. Also It can't an instant migration. The world can't just decide tomorrow to be IPv6. Right now today theres two networks being advertized IPv6 and IPv4. You can actually sign up right now for IPv6 address space and a P2P tunnel to advertize your IPv6 address space to everybody else that has it.

Eventually most major networks will be advertizing both and then as time goes on teh clock will ticket and jackie chan and all his buddies will be told to request and advertize IPv6 if they don't then me(ISP) will just not be able to reach them anymore because I'll not be using/advertizing an IPv4 subnet anymore.

Probably get customer tickets saying "Cant reach candyv-jayemporium.com" and then you to a who is and its still advertizing IPv4 ip'd server? tough shit. Try mistertoadsbaconstrips.com instead.
 
I also hear a lot of things about a shadow network starting up once we reach global wifi coverage but I don't give a lot of thought to it.

you don't have to really unless you live in a country where you have to go through 20 proxies just to get onto Google or some porn site. Most internet filters are setup for ipv4. Using 6 its not getting blocked. Dunno if ipv4 is going to remain or going to get phased out when 6 is the standard one day in the distant future but I can see some filtering mayhem if ipv4 remains. You have to setup for both otherwise using the other you can bypass it.
I don't think ipv4 will be lost because there's no reason to get rid of it when 6 is the norm.
 
IPv4 is easy enough to keep in short term memory when I couldn't copy paste it. At least IPv6 will let you shorthand/abbreviate sections with zeros:

2002:0000:0000:0000:0000:0000:0a00:0001 ====> 2002::a00:1

Hopefully in our life time we'll mainly be dealing with zeros.

Most people I meet are Zeros :p
 
IPv4: 4,294,967,296 address (were almost out)

IPv6:
340,282,366,920,938,000,000,000,000,000,000,000,000 ish addresses.
 
doesn't work quite like that the IP has to be routable if you just had an IPv6 ip address you can't any where that doesn't advertize IPv6.
Just as many consumers use NAT to put multiple machines behind one public v4 IP ISPs can use NAT to put multiple customers behind one public v4 IP. Given that IPv4 IPs have already basically run out and many important websites are still v4 only the ISPs won't have much choice but to do this.

The only question is will they ALSO offer IPv6. My betting is that the better ones will while the shittier ones won't.
 
A giant NAT at the ISP level seems like another huge set of problems. Is that solution seriously considered instead of going to IPv6?
 
10/10 for your IPv4 stability and readiness, when publishers offer both IPv4 and IPv6
0/10 for your IPv6 stability and readiness, when publishers are forced to go IPv6 only

Ditto. I love my ISP. 0/10 for IPv6 only.
 
Ditto. I love my ISP. 0/10 for IPv6 only.

do you have a router that supports ipv6? turn it on and you will go to 7/10. my router is running 6to4 tunnel (i set ipv6 to auto detect).

anyone here part of comcasts ipv6 test program?
 
ipv6.jpg
 
Back
Top