Piotrek_PL
n00b
- Joined
- Jun 17, 2013
- Messages
- 15
Hi there! Its my first post here so I thought it would be nice to write a few words about myself before I proceed to the project log. Im not a native English I live in Warsaw in Poland but I will do my best to use proper English Ive completed several small mods that are not even worth posting here but I think Ive learnt a lot while building them. Oh how much metal sheets I have trashed before Ive caught how to do stuff.
Now thanks to my older brother whos set up a small workshop in the basement I have a chance to make something better.
Ok but lets get back to the project. Ive stared it in July 2012 and I kept a log only on my local forum. Now the build is quite close to an end so I decided to share it with you.
I was thinking about a way to write this log for a while and because theres a lot of stuff to show Ive decided that the best way would be to divide it by particular parts of the case. I dont want to spoil the fun and end this log too quickly And I must admit that writing this log takes more time than I expected.
Hardware. It's not really anything to be proud of, just my computer for every day usage.
CPU: Athlon II x4 640
MB: MSI 870-C45
RAM: 2x2GB Kingston HyperX
GPU: GeForce GTS450 512GDDR5
HDD: 120GB Kingston SSDNow oraz 250GB Seagate
PSU: Chieftec 450W
Im proud to say that all water cooling parts used in this build were sponsored by EK Water Blocks.
I want to make a case that will look like old, a little seedy like it was used for many years in bad conditions, in a factory or something. You know rust, cracks and so on. I was inspired by some old control and measurement instruments and stuff that Ive found on the nearest scrap yard
Ive started looking for some case in the online shops and I decided to buy second hand Chieftec BX-03. It was cheap and looked like easy to mod.
Ive started from modding the front panel. Striped parts removed and mesh put instead. Luckily everything was mounted only with some latches so there was no need to cut.
Then I cut the mesh and bent it. Its all screwed with nice rusty screws that I kept for a special occasion.
Overall view of the front panel.
The right side of the case also needed some change. There were two air-holes, I decided to get rid of them and put some mesh instead.
Again: cutting and bending and finally it's a perfect fit.
In this photo you can see the screws but then I decided to use pop-rivets, but the mesh must rust before riveting it.
I left all the mesh outside on the rain to rust and started work on the left side panel. There will be a lot to do with it
More to come soon...
and sorry for my bad English
Now thanks to my older brother whos set up a small workshop in the basement I have a chance to make something better.
Ok but lets get back to the project. Ive stared it in July 2012 and I kept a log only on my local forum. Now the build is quite close to an end so I decided to share it with you.
I was thinking about a way to write this log for a while and because theres a lot of stuff to show Ive decided that the best way would be to divide it by particular parts of the case. I dont want to spoil the fun and end this log too quickly And I must admit that writing this log takes more time than I expected.
Hardware. It's not really anything to be proud of, just my computer for every day usage.
CPU: Athlon II x4 640
MB: MSI 870-C45
RAM: 2x2GB Kingston HyperX
GPU: GeForce GTS450 512GDDR5
HDD: 120GB Kingston SSDNow oraz 250GB Seagate
PSU: Chieftec 450W
Im proud to say that all water cooling parts used in this build were sponsored by EK Water Blocks.
I want to make a case that will look like old, a little seedy like it was used for many years in bad conditions, in a factory or something. You know rust, cracks and so on. I was inspired by some old control and measurement instruments and stuff that Ive found on the nearest scrap yard
Ive started looking for some case in the online shops and I decided to buy second hand Chieftec BX-03. It was cheap and looked like easy to mod.
Ive started from modding the front panel. Striped parts removed and mesh put instead. Luckily everything was mounted only with some latches so there was no need to cut.
Then I cut the mesh and bent it. Its all screwed with nice rusty screws that I kept for a special occasion.
Overall view of the front panel.
The right side of the case also needed some change. There were two air-holes, I decided to get rid of them and put some mesh instead.
Again: cutting and bending and finally it's a perfect fit.
In this photo you can see the screws but then I decided to use pop-rivets, but the mesh must rust before riveting it.
I left all the mesh outside on the rain to rust and started work on the left side panel. There will be a lot to do with it
More to come soon...
and sorry for my bad English