Windows won't post past load on 2.4c

mrtheshaggy

[H]ard|Gawd
Joined
Jun 28, 2003
Messages
1,209
P4 2.4c
256mb pc2700 XMS (CPU:RAM set 5:4 to run ram at 166)
Abit ai7
Sapphire Radeon 9500np
Enermax 350w psu
15" viewsonic ve155b LCD
XP home

I just put this rig back together and tried to boot it up. It goes as far as the windows loading and then right when its supposed to post windows logon the monitor loses the signal. I thought it might be that i put a radeon graphics card and that windows installation is used to a 6800gt being there. So I tried booting into safe mode. Same problem. Then I put a G4mx440 in the slot and booted up. No go.

Could the power supply be too weak for this system?
 
PSU should be plenty...

Is the hard drive pulled from another machine, if that is so, WinXP does not like to travel between different systems, usually causes lots of problems.

I would probablly try chaining the drive off another computer, pull the files you need off and then reload the OS
 
You can do that by reinstalling windows again, but before that ..

there's one thing you haven't told us if you've tried and that is reseting the CMOS...

Try doing that first. Switch off the power supply and set the CMOS jumper to 2-3 instead of 1-2 for a minute, set it back to 1-2, switch on the power supply and then start the computer again.

Good luck
 
if you need your files, throw the hard drive in another system and get the files off it. then format the drive in the comptuer you want it in and reinstall windows.
 
mohammedtaha said:
You can do that by reinstalling windows again, but before that ..

there's one thing you haven't told us if you've tried and that is reseting the CMOS...

Try doing that first. Switch off the power supply and set the CMOS jumper to 2-3 instead of 1-2 for a minute, set it back to 1-2, switch on the power supply and then start the computer again.

Good luck

Already have. When I was putting the mobo in a new case I juggled the cmos jumper until I was ready to boot.
 
lithium726 said:
if you need your files, throw the hard drive in another system and get the files off it. then format the drive in the comptuer you want it in and reinstall windows.

Its just gonna be a folding rig and I have to do this to 2 more computers that were more of a mess than this was one. I just wanna take to shortest path.
 
Negative on the windows problem. Its hardware. Whenever it changes screens the lcd says "no signal" and it keeps rebooting. I'm gonna try my OCZ out of this system and see if the problem persists.
 
Well the lcd saying "no signal" on and off was the video card. I put the g4 mx440 back in and that stopped. As for the random restarts. They are still happening. Makes me think more and more its the psu.

Let me be more specific about the psu. I bought it in the 133fsb days of the P4a and the Athlon xp's. Its an enermax eg365p-ve.
 
mrtheshaggy said:
Let me be more specific about the psu. I bought it in the 133fsb days of the P4a and the Athlon xp's. Its an enermax eg365p-ve.

Just to be SURE (I'm almost positive it needs replacing) what are the amp ratings on it? 12v shouldn't be anything under...16?
 
mrtheshaggy said:
Well the lcd saying "no signal" on and off was the video card. I put the g4 mx440 back in and that stopped. As for the random restarts. They are still happening. Makes me think more and more its the psu.

Let me be more specific about the psu. I bought it in the 133fsb days of the P4a and the Athlon xp's. Its an enermax eg365p-ve.

I would doubt the RAM before the PSU, that is plenty for that system. Did you try the OCZ yet.
 
Back
Top