which wires are on which rails?

Joined
May 15, 2008
Messages
18
If I wish to be certain that I have devices running on different rails, how do I know which wires or connectors to use?

-----

For example, I have an Antec Earthwatts EA380. I run a 65 watt CPU and six HDDs--that's all. The specifications from Antec say that it has two +12v rails--one for the processor, and one for the motherboard and peripherals.

All six disks were connected to the same wires (three molex connectors in parallel with splitters to dual SATA power connectors). Two hard drives were not being detected by the BIOS or the OS. These two disks happened to be connected at the very end of the chain. I moved them to the other wires (the other chain of molex connectors), and now they are detected just fine.

Based on the specifications from Antec, both of these two chains of molex connectors should be on the same +12v rail, so it shouldn't make any difference. I can offer two alternative hypotheses:

(a) They are actually on separate rails, so those two disks are now supplied with sufficient amperage.
(b) They are on the same rail, as Antec claims. Because they were at the end of the chain, with all of the disks spinning up at once, sufficient amps were not available at the end of the parallel chain when needed for detection. Moving the connection to the other chain allowed the amperage to balance more evenly between the disks during spin-up.

If (a) is true, I just need to put three disks on each chain, and I should be fine.
If (b) is true, I think I need a PSU that can handle more wattage.

Would you agree?

Responses are appreciated!
 
If it's an Earthwatts of Seasonic design, chances are there are actually no separate OCPs in place, but the PSU might actually be a single rail design in practice, meaning it doesn't matter what the label says. This is often the case with Seasonic PSUs. (The M12/S12 design).

Edit: If the above is not the case, and there was not enough power to spin up the disks, the OCP circuits should have shut down the PSU. The Molex connectors might be defective in some way.
 
Last edited:
I believe the EA380 is a single-rail PSU. Anyway, your PSU should be sufficiently powerful to run your entire system, so if you just split the drives across two different wires, you should be fine.
 
How long is the chain? Did you have any splitters? Do you own a multimeter?

I don't have a multimeter.

I hope this helps:



g64l2hlh1
 
To me this looks like the wires are not heavy enough to power all 6 drives from 1 branch. You will be totally fine to run them from different branches.
 
Why not use 1 Molex to sata adapter and the 4 Sata connectors instead of the 3 adaptors?
 
To me this looks like the wires are not heavy enough to power all 6 drives from 1 branch. You will be totally fine to run them from different branches.

This makes sense to me. Especially when all of the drives are spinning up simultaneously, the wires maybe just aren't large enough to carry sufficient current to those last devices. If true, then it's not the shortcoming of the power supply. Good news!

Why not use 1 Molex to sata adapter and the 4 Sata connectors instead of the 3 adaptors?

I like using the splitters because they have locking SATA power connectors. The SATA power connectors from the PSU are non-locking.

Thanks for the help, everyone! I appreciate it greatly.

JLR
 
P.S. I got an APC UPS SUA750 (500 watt). The system runs at 20% load, or 100 watts. So 380 watts max is definitely sufficient from the PSU.

Thanks again for the help! This is running great, now.
 
Winged: Did you do the wiring job? If so...nice job! very clean my friend. Top notch!

PS: BTW...What case is that?
 
Back
Top