Weird voltages - am I reading this right?

jamsomito

2[H]4U
Joined
Aug 29, 2010
Messages
3,202
First and foremost I'm no expert. I know enough to be dangerous and that's about it. This thread is inquiring about CPU, RAM, Mobo, and PSU voltages... I couldn't find a better place for the thread so mods please move if you see fit.

These voltages may very well have been this way since I built my computer a year ago or so, but I haven't ever checked until recently. I picked up a CM 212+ to keep my CPU cool while folding (for Team 33 of course) and when I installed it, there was a ton of headroom so I decided to OC. I'm currently at 4.4 GHz at around 1.28V... I think.

Here are the voltages of concern:

CPU Voltage is set to 1.36V in the BIOS, but CPUZ is showing Vcore is 1.272V. I'm assuming Control Center is setting VID and CPUZ is showing Vcore. Someone correct me if I'm wrong. Either way I think these voltages are within acceptable ranges for 24/7, but depending on which is the one to watch, I may have a lot more room to keep going up.
VCC3V: 3.36V (is +12% ok?)
DRAM Voltage: 1.5055 V, but Vdimm in SpeedFan is 2.21V :eek: Are these two points different?
VCC1.5V: 0.74V (is -50% ok?)
VSB3V: 3.23V (is +8% ok?)
+12V: 10.38V (seems really low @ -14%)

I have speculations about some of these, but I wanted to hear it from you first. Any help is appreciated. System specs and screenshot below. Thanks!

MSi Z68A-GD65 G3 mobo, bios version in screenshot
OCZ550FTY - "550W" PSU
i5 2500k @ 4.4GHz, 1.28V
8GB, 2 dimms DDR3-1333 RAM - 1.5V, attempted to run at 1600, not sure if my dumb BIOS kept that setting though...
MSi R6870 Hawk
1x SSD
1x SATA spinner HDD
2x IDE spinner HDD's
1x SATA DVD burner
Other random peripherals - PCI Audigy 2 ZS, cheapo IDE controller card.
8 case fans.

weirdvoltages.jpg
 
Yea those numbers are definitely weird. First thing I would do is go into the BIOS and look around in there. There's usually a hardware monitor that gives you voltages and fan speeds. Do those look correct?

The numbers in Control Center look more real than Speedfan. Try Realtemp and Coretemp and compare voltages Speedfan may just be reporting it incorrectly.

As for the CPU voltage was this pic taken under load or at idle? If idle the voltage may be low because the CPU is clocked down a bit. If load then you may need to enable LLC to keep the voltage up although if it's stable that might not be necessary.
 
Use AIDA64, SpeedFan and every other app such as CPUMonitor, Real/CoreTemp etc never seem to report all of them accurately (in my experience), or the ones that are not accurate are waaay off. Free Version of SpeedFan is always fairly outdated, thus will not necessarily have the correct PLL and/or Super I/O Chip values to make accurate readings. Sometimes a new revision of chip comes out that is 99% the same as before but a register value shifts enough to throw a reading off, for example that could be why your DDR voltage is reading 2.21V. AIDA's was off on a number of settings but I emailed them with what ASRock's program was reading, as well as what my own Multimeter taken reading results were and they made the proper adjustments in a later update.
[DISCLAIMER: unless you have dedicated motherboard probing points, or know where to otherwise take readings from and have a very steady hand, I do not suggest using a multimeter since bad things can happen. I've slipped and caused a short on a number of occasions, one ultimately resulted in the demise of that board, the other times I was fortunate enough that it only tripped the Mobo/PSU's short-circuit protection feature and shut the system down.]

Control Center, which I've not used so am only guessing, looks to be just what values are set in the BIOS and are not real-time readings (but someone correct me if I'm wrong). CPUz (and AIDA) shows the realtime and factors in any power-saving that is taking place. For example, even though I don't have Cool-n-Quiet enabled, my AMD Llano (and original Bobcat E-350) will both drop voltages way down under idle (E-350 would go to about 0.650V even at full speed), so that isn't anything to worry about that I can see. To make sure you can just load up something like LinPack (IntelBurnTest is a GUI version that is easy to use) while CPUz is open and see what it reads out. If it is some sort of power saving (CPU or BIOS implemented) then it'll then go to around your set voltage. There are other factors at play so it could be higher or lower depending on various BIOS settings or power-phase design quality.

But anyways, I wouldn't worry too much that they aren't what they are set as, at least when under load. When in doubt there is always the BIOS page to give you at least an accurate idea of where they'll be around, just not necessarily what their load readings will be.
 
Software readings are rarely correct. Only true way to check voltages is with a multimeter.
 
Back
Top