Trouble shooting tips needed

TomFool

n00b
Joined
Sep 18, 2004
Messages
14
My 3+ year old rig has been down for over a month. I have some time coming up soon (finally)
to tear the pig down and find out what's broke.
System just went black to screen as I was loading up half life for my kid to play.
ALL fans and lights come on and lights for optical drives flash. Reset button does nothing, and hard drive led shows no activity, nor can I hear them spin up. Bootup only gets me black screen, no bios, nothing ! Only way to shut down is 4 sec hold on power button !
System specs........
Apvia Aspire 500 watt psu
Asus P4C800E Deluxe
3.4 gig Northwood cpu
I Gig OCZ Gold something or other
Asus AGP X800XT PE with upgraded vpu cooler
2 40 gig Raptors (not raid)
2 Plextor optical drives
1 floppy
Soundblaster audigy 2 platinum
System I built for my MOM is similar with Abit IC7G mobo, ocz ram , and northwood 2.8 cpu.
Would appreciate any thoughts on what the likely culprit is. But Most important to me is advice on how to use my mas' rig to test my parts without screwing up either system. (especially hers). Oh yeah, both rigs are running WinXP Pro serv2 oem.

Help Please....Thanks
 
Thanks for the heads up on the psu spartacus. I knew it was low quality unit, didn't know it was that bad though. I just ignored it cause all was fine and I didn't overclock.
I will replace it. If the psu is not the cause of my breakdown and I need to swap parts around to find the culprit is my oem winxp going to need to be re-registered or will it all be fine once everything is repaired and reassembled ?
 
Try swapping out the video card... And as said the PSU should be replaced regardless of rather it's the problem or not.... But definitely try your mother's video card in your machine and see if that helps... And as long as you don't have to replace your motherboard, your Windows install should be fine.. Good luck.....
 
One trick to try it disconect-remove everything not need to post.
All drive, sound card, case fans, etc, etc.
All you should have left is PSU, MoBo, 1 stick of ram, vid card & CPU with heat sink and fan.
Make sure the speaker is plugged into the correct header.
Will it post ?
If not do you get any beeps from it ?
If no post and no beeps the remove the vid card and power on.
Do you get the beeps for a bad vid card ?
Power off and replace vid card, remove memory and power on,
Do you get beeps for bad memory ?
If you get any beeps with one part removed and no beeps otherwise then the removed part is bad.
If you get no beeps at all then it either a bad PSU, CPU or MoBo.
If it posts at min spec but not at full spec then either the PSU cannot take the load or there is a bad part that stops it from posting.
Thats one way to cut down on variables when troubleshooting.

Luck .............. :D
 
Try swapping out the video card... And as said the PSU should be replaced regardless of rather it's the problem or not.... But definitely try your mother's video card in your machine and see if that helps... And as long as you don't have to replace your motherboard, your Windows install should be fine.. Good luck.....

Exactly. :)

Try the easy stuff first, video card, memory, CPU.
Assuming you replace the PSU as the first step, swapping out the video card, memory, and CPU will give you your answer.
Pull out that sound card and disconnect all drives until you get it to POST too.
 
Thanks guys. I'll post back this weekend with a recap of all the symptoms and what I find the culprit to be. Hope it isn't my cpu or mobo so I can revive this beastie and turn it over to my kid when I build a new rig around nov/dec.
 
Found It !.............I think
Yanked out Asus X800XTPE and booted up to get 3 fast beeps, hear my hard drives spin up and get activity on hd led.
Hmmmmm, dug up an old Geforce 2 gts AGP card, installed it, fired piggy up and found all is well and good.
Does this truly mean that the X800XT is trash, or could it still be my psu.
If card is trash would an X1950XT be a good replacement or are there still heatsink issues with them ? What brand/model card would you suggest ?

Thanks again guys :)
 
Just tried my X800XTPE in another rig with new and good psu. It's dead for sure.:mad:
Any recommendations for a replacement AGP vid card ?

purty please:cool:
 
X1950pro would be a good choice.. I have a system that is fairly similar to yours, you have a better CPU, but other than that.. pretty similar... You may experience a bit of a bottleneck due to your CPU, but you will still see a big improvement in performance...
 
Thanks exhaust, just been surfin reviews. I think you are right, I'm going with the x1950pro.
Can any one explain why my dead card was stopping my rig from booting, not even 1 spin from hard drives :confused:
 
A dead card will prevent your system from posting.. and no post = no boot.

The minimum requirements for a post are a mobo (duh) cpu/hsf, memory and a video card (or on-board set in the bios...if that's available on your board)... if those components fail to pass post, the system will not go any farther... that's it...basically anyhow...
 
Back
Top