Trouble installing vista on new Raid 0 setup

SocceRich20

2[H]4U
Joined
Aug 4, 2003
Messages
2,512
System specs:

Q6600
Abit AB9 QuadGT
2x 2GB Geil
8800 Ultra
2x 500GB Samsung SATA
1000w PSU
Samsung SH-S203B SATA DVD-RW

Basically, when I go into the BIOS and set SATA mode to RAID, it shows me the Itel Matrix boot screen where it lets me set up my raid 0 array as usual. However, it then refuses to recognize the SATA DVD drive and therefore I can't boot from it to install Vista. When I set the SATA mode to IDE, I can get the Vista setup started, but it shows me the two SATA drives as separate drives rather than RAID. I've tried using an IDE DVD burner, as that's what I used to install Vista on my Q6600 system with an IP35 Pro motherboard, however, I ran into problems that way too. When I have the JMicron controller enabled, it does not even bring up the Intel Matrix raid CRTL-I option after POSTing, it skips right to the JMicron controller that only shows my IDE DVD burner, and when I go to install Vista it shows me no available hard drives to install on. The only way to get the Intel matrix raid thing to load and see my two drives is to have the JMicron controller disabled, but that makes it so that the system doesn't see my IDE DVD burner and therefore I once again can't boot from the install CD. Maybe I'm missing something obvious, but if someone could help me resolve this I'd greatly appreciate it.
 
Try an Abit forum, I know there are several around. You need to find somebody with experience on that mobo.

I have a Gigabyte DS3 that also has the JMicron controller. That controller has both SATA (with RAID) and ATA functions. I think some mobos only use it for the ATA functions though.

See if your BIOS setup has separate settings for the JMicron controller and the Intel controller. If the JMicron is controlling some of the SATA ports on your mobo, make sure you are using the correct ports. My mobo also has both JMicron & Intel controllers, but the SATA port connectors are different colors to show that they are on different controllers.

You have to use the correct ports and the correct mix of BIOS settings.

EDIT: I got curious about that mobo and found this:

"During storage drive testing we noticed the board would not run our Optical drives in DMA mode and defaulted to PIO mode regardless of how the JMicron controller was setup when utilizing the latest firmware and driver updates on our test image. We had to complete a new XP SP2 install with the JMicron controller setup as a RAID device in the BIOS and load the driver set via the F6 command in order to get DMA support for the Optical drives.

We also noticed IDE support from the JMicron controller was not available if we were using a RAID setup on the Intel ICH8R controller. We have noticed this before on other motherboards utilizing the JMicron chipset. However, this issue has generally been solved so we expect abit to have a solution shortly. For now, we recommend purchasing a SATA DVD drive and turning off the JMicron controller altogether unless you need the e-SATA support. If you use a SATA optical drive on the Intel controller the board will not recognized the drive if you have RAID enabled so this a catch 22 situation."

http://www.anandtech.com/mb/showdoc.aspx?i=2911&p=6

EDIT #2: In light of the above info, check for BIOS updates.

EDIT#3: Ok, I don't even have this mobo and I found the solution just by reading the BIOS update page. :)

Version: 11 File Size: 415 KB Released: 2007-03-27



* Enhanced overclocking ability.
* Modify the Voltage adjusting function.
* Fixed an issue that the system hangs during Vista installation, when using a Kentsfield CPU.
* Fixed an issue where the system sometimes hangs on POST code 2A.
* Fixed the JMB363 performance issue.
* JMB363 now works as intended when enabling ICH8R RAID ROM.
* The "EIST adjusting" function now works as intended.
* BIOS compiled date: 3/27/2007
 
Back
Top