Tips to make my overclock better/more stable?

apav

Gawd
Joined
Sep 15, 2011
Messages
524
Hey guys,

I have a i5 2500k and an Asus P8Z68-V (original, not Gen 3 version). I had a stable overclock at 4.5ghz for some time, but I feel that many of my settings weren't optimal, and ontop of that even though I had my voltage lower, for the most time I was getting 1.35V. So I wanted to start from scratch with new overclock settings, and see if I can get 4.5hz with less voltage, possibly being more stable as well, although I've never crashed once with my past overclock.

So here it is. I am listing the settings in the ASUS Bios, so these settings may be different for other motherboards.

BCLK: 100.0
Turbo Ratio: by all cores
Multi: 45x
PLL Overvoltage: Auto
EPU Power Save: Disable
OC Tuner: Cancel/Off
CPU Ratio: Auto
Speedstep: Enabled
Turbo: Enabled
VRM: 350
Load Line Calibration: High
Phase Control: Optimize
Duty Control: Extreme
CPU Current Capability: 110%
CPU Voltage: Offset Mode
Offset Mode Sign: +
Offset Voltage: Auto
Adaptive Thermal: Enabled
Active Cores: All
Limit Maximum: Disable
Virtualization: Disable
CPU C1E/C3/C6: Enabled


I pulled these settings from a thread from over a year ago, so again I don't know if it is optimal, but it seems like a good start! I tested it in Prime 95 for an hour (I know I will test it for longer, I just wanted to get quick results:
8507382068_e11907d445_b.jpg


Why am I getting on average 1.4v, which is higher than previously before? I assumed changing to offset mode would help the voltage. If not offset, how can I get the voltage down to 1.28-1.3v (which I have seen before for this cpu at 4.5ghz)? Should I change the LLC? Any other general tips you can offer me? Thanks guys :)
 
Done some testing so far. At 110%, High LLC and no power setting selected in the ASUS BIOS, I wasn’t actually able to get to my desktop (blue screens or frozen black screens) until V-Core was at 1.3v. Then, it would instantly freeze up as soon as I started a P95 test. So I checked CPU-Z and when my v-core was at 1.34v, I was getting 1.36v at idle, and 1.304v in P95. At 1.35v, I was getting 1.312-1.32v. Still were crashing after mere seconds. So I went into the BIOS, turned on high performance in the main menu, set power to 120%, and increased LLC to ultra high. Now, at 1.36v in the bios, I think I found what might be stable. At 1.344-1.36v in P95, it has been running for 20 minutes so far with no freeze or crash, and none of the cores have broken 70C yet! I realize I will have to run P95 for hours, but this is the first time tweaking my voltages where P95 didn’t immediately freeze.

Now my questions are this:
1.) Should I keep the LLC on ultra high and keep this voltage, or lower the voltage and increase the LLC to extreme?
2.) Once I find a stable voltage, should I go back to offset mode?
3.) What about PLL and VCCIO? Currently I have these on auto.

Again, here are my settings:
ASUS BIOS Power Mode: High Performance
BCLK: 100.0
Turbo Ratio: by all cores
Multi: 45x
PLL Overvoltage: Auto
EPU Power Save: Disable
OC Tuner: Cancel/Off
CPU Ratio: Auto
Speedstep: Enabled
Turbo: Enabled
VRM: 350
Load Line Calibration: Ultra High
Phase Control: Optimize
Duty Control: Extreme
CPU Current Capability: 120%
CPU Voltage: Manual- 1.36v
Adaptive Thermal: Enabled
Active Cores: All
Limit Maximum: Disable
Virtualization: Disable
CPU C1E: Enabled
C3 and C6: Auto

I’m getting lower voltages in Prime 95, currently around 1.344-1.36, avg about 1.352v. First overclock yet to not freeze as soon as Prime 95 starts, let alone pass tests.

So is this just a bad overclocker then? I’ve heard 4.5GHz is capable at 1.27 or 1.28?

Any other tips with my settings would really be appreciated! Please excuse my spelling :)
 
It depends on what speed you want?
Your temps are great, so you do have more headroom possibly.

Does your 212 have dual fans?
 
Afraid not :( My temps are great, but my overclockability seems pretty mediocre. And I don't know if I'm doing it right with my settings either. What could I push it to? Would say 4.6 make a noticeable difference in games over 4.5?
 
Afraid not :( My temps are great, but my overclockability seems pretty mediocre. And I don't know if I'm doing it right with my settings either. What could I push it to? Would say 4.6 make a noticeable difference in games over 4.5?
It wouldnt make much really, but I wouldnt go past 1.4v.
If you want to try for your max OC, you can try 1.4v and increase multi until its unstable, then back off 1. Just make sure your temps are still good.(adding a 2nd fan depending on your case might help)

@ 4.5 you will be fine even for the few games that really push your cpu.
 
It wouldnt make much really, but I wouldnt go past 1.4v.
If you want to try for your max OC, you can try 1.4v and increase multi until its unstable, then back off 1. Just make sure your temps are still good.(adding a 2nd fan depending on your case might help)

@ 4.5 you will be fine even for the few games that really push your cpu.


I actually had offset + mode on, and it was giving me ridiculously high voltages, higher than 1.4, both on idle and in Prime 95, so I switched to manual because I got scared. However I don't know if I should switch back to offset, and do - this time. What do you think? This seems to be a stable overclock, no crashes yet and its been more than an hour.

Believe it or not the whole reason I am overclocking is because my i5 2500k was bottlenecking me. Probably because I game at 1440p, I saw a 10-15 fps increase in all my games when I overclocked from stock to 4.5, especially the demanding ones.

Edit also CPU-Z says my DRAM frequency is only 800 MHz? In my BIOS it says my target frequency is 1600. Maybe because I'm in manual and not XMP? Is there a way I can fix this? Thanks again :D
 
Its been a long time since I have played with the bios, but you want the voltage to stay stable at max load, which is vdroop. I am not sure if it was offset or LLC?

Memory is ok, since its DDR, 800 x 2 = 1600, IIRC.

Once you do get it stable at the higher speed, check how much you gained to see if its worth running it like that 24/7.
 
Oh ok, they're not 1600 each? I didn't know that. And I'm not sure too, offset and LLC seem like they do the same thing. I'm of course, a noob, but don't they determine how close or far the actual voltage is to vcore?
 
Oh ok, they're not 1600 each? I didn't know that. And I'm not sure too, offset and LLC seem like they do the same thing. I'm of course, a noob, but don't they determine how close or far the actual voltage is to vcore?
I have my cpu LLC set to 1, which is the highest and since I dont run my comp at full(f@h) I dont mind the setting as its stable.
 
I say you have a great overclock @ 4.5 in your second post.... key was taking the auto voltage out of the equation. You can push a few 100 mhz out of it, I bet, but you'll see diminishing returns in terms of heat output and power consumption.
 
Back
Top