this blows

noremacyug

[H]ard|Gawd
Joined
Apr 15, 2004
Messages
1,641
ok, me and a friend just put together his computer with an abit is7 mobo, p4 3.0ghz cpu, and a samsung 160gig sata hdd etc. anyhow, i've installed sp-1 for xp pro and even installed the hotfix thats suppose to take care of the over 127gig issue. however, it still isnt working right, we can only access 127gigs of the hdd. what else can we try? also the cpu temp is showing to be around 53C idle. that seems way to hot to me. it use to show that it was idle at 63C but flashing to an updated bios brought it down to 53C. what do you guys think. needin a bit of help here.


thanks
 
use the disk that came with the drive or download it off their website...

i had same problem and i had to use the drive setup utility to get it to recognize the whole drive....

sucks but until they realize its dumb and change it... we're stuck.

:rolleyes:
 
GSRwBOOST said:
use the disk that came with the drive or download it off their website...

i had same problem and i had to use the drive setup utility to get it to recognize the whole drive....

sucks but until they realize its dumb and change it... we're stuck.

:rolleyes:

what disk might that be. i dont remember if one came with the drive or not. i have a sata driver disk, but i think thats for the is7 raid function. i checked samsungs site and the only download they have for the hdd is of the manual. nothing else.
 
noremacyug said:
also the cpu temp is showing to be around 53C idle. that seems way to hot to me. it use to show that it was idle at 63C but flashing to an updated bios brought it down to 53C. what do you guys think.

I think the following:

1. HSF is not sitting correctly on the CPU. Reset the HSF.
2. You put too much thermal paste. Apply only a very thin layer... thinner than a piece of paper.
3. If #1 doesn't work, then get a better HSF.
4. If #3 is not in your budget, then lap your hsf to remove any machinery marks and flush the surface to make better contact with the cpu.
4. You have a P4 Prescott which runs very hot.
 
You need a copy of XP Pro with SP1 or a burned copy with SP1 slipstreamed into it.
 
Torquemada XP said:
You need a copy of XP Pro with SP1 or a burned copy with SP1 slipstreamed into it.

This is the solution.
 
Yea you need SP1 when you install XP, find a copy and use it along with your key and you should not have a problem with drives over 127GB.

And shorten you sig, its four lines to long. Just some friendly advice before a mod sees it and does it for you. :p
 
In your current situation, you must have the following in place:

Proper BIOS
Proper Drivers
SP1

You have each of these.

Now goto Admin Tools/Computer Management/Disk Management. You will see the missing giggage. Partition, format, and give a drive letter.

If you want the entire drive to be one partition, you must slipstream SP1 into your install disc.
 
Hmm, I have a feeling it does support over 137GBs now... but that you already have a 137GB partition. If you don't want to format, seeing as this would be a bit counter productive in your case you can try this:

1. right click on my computer and select 'manage'
2. under storage select disk management - at this point you'll see your HD as well as any partitions on it. If every thing is as I think it should be Disk 0/basic/152GB with a 137GB partition on it.
3. resize the partition with a third party program like partition magic or do the next steps.

4. right click on disk 0 (or whichever is the HD) and select convert to dynamic disk
5. once you have done this you can resize the partition on that disk making it larger, however it will not allow you to make partitions smaller once they have been enlarged. just a warning I haven't really used this feature much with XP so I can't speak for how well it works.

heh, if this isn't whats going on I'm clueless... but good luck :)
 
mmmmk. while i dont still have the computer here to work on it. i still want to find out how to fix it for him. as far at the heatsink goes, i dont see any possible way its on there incorrectly. i tried putting it on one way, then spun it around and tried it the other way. no difference was made. originally the thermal pad that came on the heatsink was used and it still ran hot. so then i tried thermal paste and it was still hot. im sure the thing is on there correctly. i dont see how i could have possibly messed it up. i think that the mobo is just showing a high temp. by the time he left we had had the thing running for hours and it was idling around 50C and would hit around 60C load.
now on to the hdd prob. i've installed sp-1, updated the bios to the newest one out, tried using wd data lifeguard tool, installed the hotfix from microsoft and we still didnt get it.
soooooo what exactly should i do.

thanks ya'll
 
If your temps are showing around 50 idle, then if you put your finger on the HSF, it will likely be very hot to touch. If its not, you have a bad reading...
 
yeah, i touched the heatsink and it didnt feel very hot. thats why i think its just the mobo.
 
The temps on this board are reported higher than actual since the temps are calculated, not measured. read the Abit offical post for this issue in their forums. BIOS 20 actually did do something for me as far as reporting the temps. Now if they would just fix the CH-5 compatibility problem, then I will be happy.
 
Back
Top