Temps on Refurbed 6600GT high

mesostinky

n00b
Joined
Sep 29, 2005
Messages
28
Hi all. I bough a Chaintek 6600GT from Newegg Refurb and I'm a bit concerned about the temps it reaches at load. Idle is 57, load is 93. Most posts I've seen for this card have the load temp from ~60-80 on the high end. I have seen a decent amount of posts from people who hit 90+ but usually they are wondering why their card gets so hot while everyone else's only hits 60 at load.

Anyway load testing is done with rthdribl v.1.2 and I get no artifacts and no lockups so far in it or 3dmark05. Buying a aftermarket cooler might make this cost as much as a new 6600GT so I'm not sure about that.

Any thoughts? Should I be returning this? Bother taking it apart and adding new paste, don't know hard it could be on this card?

Thanks
 
My eVGA 6600GT routinely topped 92 under load using stock cooling.

After re-seating the stock cooler and applying Arctic Silver 5 it would load at around 68.

After buying a VF700-ALCU and using it it loads at around 54.

My overclock benefitted greatly.

Conclusion? If you can -- grab a VF700 (ALCU or CU). They are very cheap now, and would probably help you a lot in getting those temperatures. There are also silencers available for 6600GT's. I understand your quarrel with having to spend more money, so perhaps re-seating the stock solution would be best before you drop more money on it.
 
Thanks ep1taph, I'm going to first try new AS Paste but I have a quick question. Based on this HSF, remove the thermal tape for the HSI and use paste or just leave it?



 
Hmm... someone else may have a bit better advice.

The surface of that heatsink looks pretty gritty -- contact may be bad.

Personally I dislike thermal tape and always get rid of it.

Be sure to keep that bridge chip cooled well also, I read they get pretty hot.
 
Well, I'm officially bummed. I took the HSF off, put on a fresh coat of AS and now it idles as 65C. Great...:rolleyes:

Guess I'll be sending this POS back to Newegg and buying a brand new one.
 
The high temp could be the reason why it was a refurb card. Probably just an RMA and Newegg turned it around and just sell it since it didn't actually die, just high temp.

Probably just bad contact, though. I remember awhile back, reading 6600GT cards review at Anandtech, they specifically stated that a bunch of the cards came with HS/Fan that tilted due to not having rubber feet under the Heatsink to stabilize it (the seating). I used to own an EVGA 6600GT and remember to look specifically for these rubber feet (four of them) and they indeed really helped with seating the HS to the GPU so no tilting can occur. I think yours might just have this problem. If you can find the correct length rubber feet for your HS, you may be able to remedy this problem w/o having to return yours.

To further help with lowering your temp, I recommend relapping the HS. It looks pretty bad. I would use start out by using 1000 grit to smooth it out, then use 2000 grit to really give you the mirror finish. If you are not into this, then, well, I guess, no other choice.
 
mesostinky said:
Well, I'm officially bummed. I took the HSF off, put on a fresh coat of AS and now it idles as 65C. Great...:rolleyes:

Guess I'll be sending this POS back to Newegg and buying a brand new one.

First, did you clean off the thermal goo that came with it before applying AS5? I always clean off any thermal goo that comes with a heatsink, whether it's a CPU HS or GPU's.
 
Upon further inspection, looks like there are only two rubber pads. There should be four. Also, on my EVGA 6600GT, they weren't pad, they were real rubber feet, not as fragile like pads.
 
He raises a good point -- my eVGA stock cooler did have these rubber feat on them.
 
Hey there, I have a Chaintech 6600GT AGP as well.
Yes, the stock cooler is rubbish, noisy as hell and it tilts so easily that it couldn't cool well and was probably endangering the edges of the GPU core.
Yes I had a full load temp of 91C (@stock) as well.

Anyway, I replaced the stock cooling with a FS-V7 for the GPU and a VHS-1 for the HSI bridge and it now loads at 66C (@560/1200).

:) Go get that cooling changed.
 
Thanks for the feedback guys! I got this for $99 and aftermarket cooling brings me to ~$130 which is the cost of a brand new 6600GT. I don't really want to try to salvage it anymore. Instead of doing that for $150 after rebate I can get a new Nforce4 S754 mobo and a 7600GS 256MB card. I'm think I'm going to end up doing that. The 7600GS performs a little better than the 6600GT and is passively cooled! Again thanks for the responses.
 
My BFG, which uses the big copper whiny fan, did 55/80. I swapped in a Thermalright V1, and in passive, it does 50/70, low fanspeed (lowest with the zalman fanmate) it does 45/58, and with the fan turned up, 43/55
 
Back
Top