System Failure, need help please

Operaghost

[H]ard|Gawd
Joined
Jun 4, 2004
Messages
1,315
I have had my system for quite a long time, at least 3 years if not 4.
System was an AMD Athlon 800 on an Asus A7V, pretty much cheapo componants cept the video card. (I got the system pretty much for free so didn't worry about upgrading it)

Now this was the deal, it had started making all kinds of racket, strange noises that I knew wasn't the HDD, loud vibrating noises. I removed the side panel and listened to it closely but couldn't locate exactly where the noise was. Being as all fans looked to be operating fine I assumed next that my PSU was dying. So I grabbed a new PSU my brother had lying around, ripped out the old one and put in the all new 420 PSU. Powered it up, No POST, no video display, and the noise was still there. I glanced at the CPU fan and noticed it was spinning sporadically speeding up and slowing down, this was a pretty generic HSF. So now I'm thinking "Oh shit, I just either fried something, or my MOBO or CPU is dead."

Now I'm no electrician, just a hardcore gamer, heart and soul. So I think perhaps my mobo can't handle the juice from this new PSU and thats why it won't post. (after reading later discovered this couldn't be the case) So I rip the new PSU out and put the old one back in, hoping that it will at least boot and I can make due with the noises until I get my new system ordered. So I get it all hooked back up, power it up. No POST, No display, still noisy. Now I'm befuddled, so I gut it. Pull EVERYTHING out and reseat it, memory, cards, CPU/HSF, the whole 9 yards. Same thing, no dice.

Now all I wanna know is what failed, so I can possibly sell or use for friends the parts that still work. I'm guessing the CPU died but it could be the mobo also? Or memory? Any suggestions on tests I could perform without buying anything?

Sorry for the long thread but I know details are important to troubleshoot.
Thanks in advance.
 
some motherboard won't start if the fan doesn't run (or run at a certain fixed RPM)
You might want to put a new Heatsink+Fan. Clear the CMOS maybe...
My friend had a 2500+XP Barton core cpu with a Thermaltake Dragon Orb on it.
the fan died and we noticed this 40 secondes later.
The cpu was still 50% alive ehhe..it was booting fine but in windows there was green line (vertical) in the screen
 
I was gonna try clearing the CMOS but the manual says I have to do something to the 2 solder points on the board, I found the points but didn't understand the terminology of what I was supposed to do exactly, It is just 2 small metal dots on the PCB. So I'm not sure if I can clear the CMOS.
Anyone else have a clue what might be goin on here or how I could test whats wrong without having another setup to swap out parts etc?
 
they probably want you to move a jumper. just pull your cmos battery out and make sure the power is connected then put it back in after a few seconds and all settings return 2 default
 
The A7V do not have a jumper ... you should short those two dots(solder points) to clear the CMOS values ...

try to change the fan ... could be the problem ...
 
how fast is the fan spinning? if you are using an amd, it could easily fry, unless you have a decent heatsink, you said it was generic, amd's aren't like intels where they slow down till the CPU basically halts, trying to save its own ass from burning, my frens AMD, well his fan died. and he didn't know, it heat up the heatsink, then the heatsink clip, then, the clip Melted the nubs on the processor grid array board, and eventually, the heatsink Poped off. seconds later he saw smoke coming out and of course the screen was frozen. when he tried to turn it on, he didn't even get a "no CPU beep sequence", it just DIED. as funny as it was for me at the time, i was amazed by all the damn smoke that came out of a burnt cheap. you could see the PCB close to melting right under the core... all black and the texture was grainy from burning into crisp.

I guess i'm saying If shorting the CMos dosen't work, check yer CPU hope that its Not dead. :(
 
I bought a new HSF, greased up the CPU, installed the HSF, connected the HDD, reseated the DIMMS. I shorted the CMOS points and powered her up.
POST!! one beep, I'm excited!
So I go into BIOS and leave everything at default for the time being.
I wanted to reinstall the cd drive since I'd completely gutted the system.
Put the CDR back in, secured the MOBO tray in place, plug the power cord back in and the system powers up, even though I didn't hit the power switch. It doesn't post so I switch it off and try again. No post, no display. Back to square one. Any help?
 
Try booting your computer with the bare essentials: CPU, mobo, PSU, no ram or video, no cards in your pci slots or anything to see what kind of error messages you get, then go from there slowy adding components in your system to troubleshoot it.
 
Yer ribbon cable... make sure you have it set up right, if you have the older ones and you have it flipped... it'll cause the computer to NOT boot at all...
 
Back
Top