SuperMicro M28E1 (Internal Mobile Rack) + SSD ??

dmw5678

Weaksauce
Joined
Jul 18, 2005
Messages
87
I have an SuperMicro M28E1 mobile rack and for some reason it is not detecting my SSD SATA drives (64GB PATRIOT). When I connect the drives directly to the motherboard and/or the raid card Adaptec (5805) I have no issues. I've also swapped out the cage for the QuadraPak Q14 with success connecting to the SSD. However, the activity lights do not function in the SSD slots. I have SAS drives (Seagate Savvios) and have confirmed each slot in the M28E1 is working with the SAS drives. My thinking is that we have some sort of firmware problem and I was wondering if any updates exist for the M28E1 or possibly any SSD drives that have been confirmed to work with the M28E1. Any assistance is greatly appreciated.



Asus P6T WS
Core I7 920
12 GB Ram
Adaptec 5805 Internal 8 port

4 x Seagate Savvio 10K.2 146GB Raid 10
2 x Patriot SSD Raid 0
1 x M28E1 Mobile rack
 
There was a compatibility issue with the M28E1 not too long ago. I would suggest you contact Supermicro and see if there is an update, perhaps you need to get the M28E2, which seems to have addressed a lot of the incompatibility issues.
 
I think this cage has an integrated SAS expander which may be causing compatibility issues, which may explain why your Savvios work properly but your SSDs don't.
 
I swapped the cable (CBL-0116L) to ports 0-3 and all is well. The activity lights still do not work with the SSD drives. The SSD’s just don’t act like normal drives -- Instant power on light when the power is applied to the cage unlike the SAS drives which implement a staggered spin up. Possibly the controller chip inside the drive does not fully implement the spec. The documentation from Supermicro does not accurately reflect the connections on the back of my M28E1. I have 8 SATA connections 4 on each side. However, I only need to use the set on the left ports 0-3 for all 8 drives. This is great for cable management in my small mini tower. Not sure how it was working with the SAS drives and not the SATA with the cable on the right side on ports 4-7. In any case all is well. Also, I have a free connection on my Raid Card Adaptec 5805 nice...

omit the mess -- this is a new build on a makeshift test bench in the corner of the basement




 
I swapped the cable (CBL-0116L) to ports 0-3 and all is well. The activity lights still do not work with the SSD drives. The SSD’s just don’t act like normal drives -- Instant power on light when the power is applied to the cage unlike the SAS drives which implement a staggered spin up. Possibly the controller chip inside the drive does not fully implement the spec. The documentation from Supermicro does not accurately reflect the connections on the back of my M28E1. I have 8 SATA connections 4 on each side. However, I only need to use the set on the left ports 0-3 for all 8 drives. This is great for cable management in my small mini tower. Not sure how it was working with the SAS drives and not the SATA with the cable on the right side on ports 4-7. In any case all is well. Also, I have a free connection on my Raid Card Adaptec 5805 nice...

The ports on the right are 2nd ports and not the PRI ports, they are designed for high availibility, high bandwidth, SAS requirements. They can also be used to expand into another unit (daisy chain so to speak).


BTW, if you have two sets of 4 ports, then you have the M28E2 not the E1.
 
No markings on the chasis. This was a defective return sent to SuperMicro. In looking at the RMA repair report it apears they exchaged the E1 for the SASEXPM28E2 for. I did not notice this until now. Thanks for the heads up. This is great so I could add another cage for more than 8 drives and/or raid card for fail over options.

Awesome
 
FYI -- Confirmed SSD's do not work on the M28E2 version only SAS drives. You will get errors and failures. So 8 Seagate Savvios - raid 10 coming soon. Should have waited until SSD's implemented the SAS/SCSI spec :(
 
Back
Top