Strange issue with Linux bootable ISO's not loading fully (taskbar, start, icons missing)

.oO

Weaksauce
Joined
Apr 27, 2013
Messages
114
I keep encountering a strange issue with Linux bootable ISO's not loading fully (taskbar, start, icons missing, and run commands not working), and am really puzzled about it now.


Tried multiple types including Debian 13 variations (XFCE, LXQT, etc), Bazzite KDE.

It still happens the same whether they have been setup through Ventoy, Belena Etcher, or KDE ISO Image Writer.


on hardware:

Asus M5A97 2.0 mobo
960T CPU
HD 7770

but works fine on other hardware such as:

HP7900:
8400 CPU
HD 5450

Desktop background loads, and with most the right click menu works.
 
I don't know shit about linux, just started using it myself. But you on some old-ish hardware. Could it be compatibility issues with the CPU or other hardware? Actually, I'm guessing strait hardware problem. If the same distros are working fine with other hardware. I'd start by re seating the RAM or swapping it, Since you have missing GUI elements. I had weird glitches happen in windows with poorly seated RAM. Memory issues could be it. From there, swap the HD7770 into the other system, with the HD 5450 and see if it acts up.
 
Which command is not working, exactly?
Things not loading in Linux live USB... probably your USB stick is dying?
Type:
dmesg or sudo dmesg into the terminal to see errors. If you see any I/O errors then it's probably your stick. Or USB port in the motherboard.
 
Thanks for the ideas.

I forget what all commands I tried but none did anything.

It was tried with different USB adapters (USB 2.0 and 3.0).


This is what "solved" it:

Booting with nomodeset added to the kernel line (pressing TAB on the boot entry, to enter "nomodeset")

But I am still wanting to understand better why or what is going on with that...
 
It is quite old, but should work fine. Verify that the programs you expect to runare actually being started, and if so, check the system logs to see if they are crashing.
 
It is quite old, but should work fine. Verify that the programs you expect to runare actually being started, and if so, check the system logs to see if they are crashing.

Everything in the live desktops (XFCE, LXQT, LXDE) seems to load/work correctly.

What specifically are you saying is quite old?
 
Everything in the live desktops (XFCE, LXQT, LXDE) seems to load/work correctly.

What specifically are you saying is quite old?
The CPU and GPU.
Booting with nomodeset added to the kernel line (pressing TAB on the boot entry, to enter "nomodeset")
Nomodeset disables kernel modesetting, which sets the gpu power state (among other things). Without it, your gpu runs in whatever default mode it boots in, which may be the lowest or the highest power state, or somewhere in the middle.

Nomodeset might be needed if your gpu isn't supported by the installed kernel (unlikely), if support isn't built in and the module isn't in the init environment (possible, unlikely?), or if the module loaded at boot is incompatible with the runtime drivers used by x11, etc. Also if the boot environment doesn't match the installed kernel, but that shouldn't happen usually, especially on a new install.

Arch kms wiki: https://wiki.archlinux.org/title/Kernel_mode_setting#Disabling_modesetting
 
Last edited:
Sorry, I'm half asleep -- almost 2am. Nomodeset might also be needed if the display system is selecting a mode which isn't compatible with your display or GPU.

In any case, you should check the system logs to see what's going on. More than likely there is something complaining in there, either in the kernel log or xorg (if your OS uses it). I would look for entries with "warn" "err" or "kms" in them, and maybe "amdgpu" or "radeon" as well.
 
Back
Top