Start up issue

JKownz

[H]ard|Gawd
2FA
Joined
Nov 2, 2004
Messages
1,257
I recently bought a WC setup. I installed it all and used non-conductive fluid. When it was all in and good to go I press the start button and all the Led's and HDD's turn on but There is no beep or post up. I tried everything. my12V is in 24 connector, Switched out ram re seated the video card and cpu. I dont know if its all of a suddon hardware issue or what. the Mobo lifters are on I double checked all connections tried everything i can, even reset bos by default,*mobo option*. I have a p5W DH Deluxe. Ocz GamerXtream 700 Watt. core 2 duo 6600. If anyone has any ideas what i should do please post. :) Thanks for reading.
 
Nine times out of ten, you just need to re-seat the CPU. Since you already tried that, I have some questions:

Is the 4-pin CPU 12V (P4) Power connector plugged in?
Does the mobo beep when you power up with no ram installed?
Does the moob beep when you power up with no vidcard installed?
Is the PCI-E 6-pin power connector(s) plugged in?

If you don't hear any beeps, make sure a system speaker is plugged into the 4-pin header, or your have your speakers/headphones plugged into the line-out onboard-audio jack (for Asus boards only). There should be a voice telling you whats wrong with the system, if your board supports it.

That PSU is FSP Epsilon based, so it has ripple at high loads. Do you have another PSU you could try?
 
Nine times out of ten, you just need to re-seat the CPU. Since you already tried that, I have some questions:

Is the 4-pin CPU 12V (P4) Power connector plugged in?
Does the mobo beep when you power up with no ram installed?
Does the moob beep when you power up with no vidcard installed?
Is the PCI-E 6-pin power connector(s) plugged in?

If you don't hear any beeps, make sure a system speaker is plugged into the 4-pin header, or your have your speakers/headphones plugged into the line-out onboard-audio jack (for Asus boards only). There should be a voice telling you whats wrong with the system, if your board supports it.

That PSU is FSP Epsilon based, so it has ripple at high loads. Do you have another PSU you could try?

1. Yes
2. Nope
3. yes a steady beep loud to lol.
4. yep

I hear beeps when something isnt in. I have a frozen cpu psu tester, everything is lighted up and working properly. So I most likely think its the mobo or a bent pin on the mobo. What do you think?
 
I concur with the board suspicion, due to answer (2). You could try another PSU if you have one around.
 
I concur with the board suspicion, due to answer (2). You could try another PSU if you have one around.

Got a EVGA NVIDIA nForce 680i SLI A1. Installed it and to my surprise *sarcasm* I hear the beep and I felt releved but my happiness was short lived. Im getting a led error message that says 7F on the board. Manual states that "POST error check---Check POST error and display them and ask for user intervention. Those are the exact words on the manual. It beeps once, all the lights go on again I dont see any video, I re-seated the vga switched memory sticks, checked all my connections still nothing, I also cleared Cmos from the board. I'm going to hang myself lol. What else can it be now?. I hear sometimes a beep that goes long then two taps basically like this. --------- - -
 
1. Yes <-Good.
2. Nope <-Bad
3. yes a steady beep loud to lol. <-Good
4. yep <-Good

If its not beeping at you for missing ram but is beeping at you for missing vid card then that the clue to follow up on.
When you take the bad part out you get beeps and with the bad part in you get nothing.
The vid card looks like is stopping it from posting.
Have you a spare vid card to try ?

edit. Ami bios, 1 long, 2 short= Failure in video system, An error was encountered in the video BIOS ROM, or a horizontal retrace failure has been encountered

Luck ........... :D
 
If its not beeping at you for missing ram but is beeping at you for missing vid card then that the clue to follow up on.
When you take the bad part out you get beeps and with the bad part in you get nothing.
The vid card looks like is stopping it from posting.
Have you a spare vid card to try ?

edit. Ami bios, 1 long, 2 short= Failure in video system, An error was encountered in the video BIOS ROM, or a horizontal retrace failure has been encountered

Luck ........... :D


Yea.....so, um put in a new card....it went threw I finally saw bios and a screen. I appreciate your time in reading and posting Tigerbiten and enginurd. :) I'm going to RMA my card and end the mayhem.
 
That would have been my next guess, lol. Glad you figured it out.
 
Back
Top