sony vaio pcg grt 100 problems in 3d

twelveparsex

[H]F Junkie
Joined
Nov 30, 2000
Messages
12,955
i've had this laptop since dec 2003; everytime i run a 3d game on here ; after a few minutes it hangs for about 30 seconds and when it comes back there are artifacts everywhere

games affected
need for speed underground
all half-life/q2 engine based games
splinter cell 1 & 2 (all water/reflections on it looks fucked up)
warcraft 3

oddly enough rainbow six 3 runs fine on it, ghost recon runs pretty well on it too; and the windows 3d screen saver doesnt screw things up either. though once it crashes these games get affected too

but after the game crashes the only way to get the artifacts off is to put it in hibernate and turn it on again or restart the computer.

updated drivers many times, never helps either

wc3.jpg


edit: its a geforce fx go5600 64MB
 
moved at authors request.

Might help to specify what graphics chip its got. :D
 
Could be a bad driver install (uninstall them completely and reinstall), or the PC is overheating somewhere. Also, avoid SONY for now on.
 
MooCow said:
Could be a bad driver install (uninstall them completely and reinstall), or the PC is overheating somewhere. Also, avoid SONY for now on.
i've installed/reinstalled drivers, formatted, everything

if overheating is the problem will underclocking solve it?
 
I have a GRT10014 with a 5600go and I have had the same problem happen to me in GTA: Vice City. Some of the game looks normal, and then everything goes to shit with artifacts. BF Vietnam works great on it though. They had some driver update in their download section, but it did nothing to help.

You may want to also enable coolbits on your video drivers and downclock the card's frequencies a bit (in fact I think I'm going to try this when I get home). I believe mine runs at 300/600, which is higher than what a lot of regular desktop fx5600's run at.
 
sKiDmArK said:
I have a GRT10014 with a 5600go and I have had the same problem happen to me in GTA: Vice City. Some of the game looks normal, and then everything goes to shit with artifacts. BF Vietnam works great on it though. They had some driver update in their download section, but it did nothing to help.

You may want to also enable coolbits on your video drivers and downclock the card's frequencies a bit (in fact I think I'm going to try this when I get home). I believe mine runs at 300/600, which is higher than what a lot of regular desktop fx5600's run at.
my stock speeds are 275 core/300 mem

what are hte stock geforce fx5600 desktop speeds?
 
Man, the thought of having to UNDERCLOCK your GPU or CPU just to have a retail stock system run stable is atrocious. Try opening up the side panel on the PC case and have a fan blowing on there to see what happens next.
 
Something you can check, if you haven't already. See if the hard drive is shutting down in the middle of the game. If so, and you have a combination of small agp aperature and not much video memory, as well as not alot of main memory, it's possible that the card is trying to swap to the HDD and it's asleep. Not very likely, I'll agree, but by the time I post looking for help, I'm ready to try about anything to get problems resolved.
If that isn't it, I'd use driver cleaner to take all old driver remnants off the HD then install latest driver. Be careful underclocking the card. Some cards go apeshit when they are underclocked too far.
 
Maybe the paste dried up. At least it's still under warranty.
 
Thats Sony for ya, I have some sony stuff and it works like shit!!!
 
As a side note.. I had a brand new Apple 15.2" PB's 9700 128mb GPU fan conk out.. chip got fried since I left it in sleep mode overnight..

Artifacts all over the screen...pretty much nothing could be made out..

Had to send it back to Apple for a logic board replacement.

Laptop was about 2 weeks old.
 
Back
Top