So what Chipset do I run for this intel SSD?

GregRotter

n00b
Joined
Mar 21, 2010
Messages
20
Hi everyone, have been a long time lurker, and after hunting high and low, and finding out lots of info, but not a clear cut answer, I figured I'd register once and for all, to see if there's anything I'm missing.

I've just recently got an Intel X25-M 80GB SSD, and am trying to find out what's the best way to have it set up.

After pulling my hair out as to why my results looked nothing like the benchmarks I had seen in reviews, I finally managed to get my system off IDE and running as AHCI. My next dillema is whether I run the 'msAHCI' 'standard' controller, or the ICH10 controller?

When I have the ICH10 controller installed, I don't have the option to plug and play my hard disks as shown here;

http://s907.photobucket.com/albums/ac274/Gregory_Kouvatsis/?action=view&current=screenshot-2.png

From what I've been reading, TRIM is meant to happen whenever the SSD is idle, and as such the drive shouldn't need anything else. Correct??

Here's what I'm getting;

http://i907.photobucket.com/albums/ac274/Gregory_Kouvatsis/bench2msAHCI.png

as-ssd-benchINTELSSDSA2M08021032010.png


Info about my drive;

CRYSTALINFO.png


All I want to know is, what is better, to have the ICH10 drivers running (IaStor) or the standard ones,(msAHCI)???? I had previously installed the ICH10 drivers running, and had the ability to run the Intel Matrix Storage tool kit, and perform the trim there. Now I've just got it back to msAHCI.

This is what I had installed;

http://downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&DwnldID=17882&ProdId=3061&lang=eng

Pretty farkin unreal that there's no way to actually see that TRIM command is reaching the SSD, as opposed to just being enabled in windows. I couldn't get the pics to show up :/

Any advice would really be appreciated :/

*specs are; My Rig;
Cpu; Intel i7 920, Ram; 3 x 2gb Corsair XMS3 DDR3 1066 Ram
Mobo; Asus P6T
OS disk; Intel SSD X25-M 80GB, Windows 7 Pro 64 bit
Storage; Samsung F1 1tb, Samsung F3 1tb.*
 
Last edited:
Hang on, so with that driver, TRIM will happen automatically, like with the MS drivers, or will I have to run it myself?

I get that with both Intel and MS drivers, TRIM will work, but from what I've understood so far, with the MS drivers, there's no 'tool' as such, and it happens automatically. With the Intel drivers I supposedly have to run the Intel matrix storage tool?

I've had a look at that link, but it doesn't say anything about support for X58 chipset :/ Am I being dense here?
 
http://hardforum.com/showpost.php?p=1035479339&postcount=1 <--- enables (realtime) TRIM for the Intel chipset drivers, so you can use either the Microsoft drivers or Intel's drivers.

Before the only options for real time TRIM'ing was to use the MS driver. And if you had a RAID set up and needed the Intel drivers were SOL. Now you can have your cake & eat it too!

Read my post! edited in "realtime"

Before only the MS driver did real time TRIM.
the NEW 9.6 Intel chipset driver does real time TRIM so you should only need to run TRIM once when you first install the driver, then from there on out, it should stay TRIM'd.

Intel's old 8.9 chipset driver did not support real time trim, only TRIM with the manual toolbox and scheduled TRIM with the toolbox
 
Hehe :D You'll have to excuse me, I had a long night trying to figure out how to stop my PC from blue screening every time I set AHCI :p

I installed the new drivers and I've gone from getting around 0.107 on the write access times, to 0.096. Other than that, not much difference. Oh well.

Thanks for clearing that up for me C-rizzle :D
 
Back
Top