Show off your Heatsink thread

ok heres the iceman on my 2.7Ghz celeron running 3.2Ghz
celeroncooler5kp.jpg


and heres the 747 jet engine i mean my cooler for my celeron D
celerondcooler0ws.jpg
 
two things, what socket type is that?
and something else ive had to say plenty, dont you want to run your memory in dual channel? Place the left memory stick one over to the left and you should be set.
 
OC_LeGeND said:
ok heres the iceman on my 2.7Ghz celeron running 3.2Ghz
celeroncooler5kp.jpg


and heres the 747 jet engine i mean my cooler for my celeron D
interesting cooler you got there, i like it! :D
 
board2death986 said:
two things, what socket type is that?
and something else ive had to say plenty, dont you want to run your memory in dual channel? Place the left memory stick one over to the left and you should be set.
thats socket 939 and his memory is in dual channel, on dfi boards, you match the colors :)
 
I have an Xp90 ..sorry no pics ..I want to lap it and maybe it will get my temps down a little. Idle 28c and load is 46c
 
OC_LeGeND said:
thanx, the top of the cooler is only about 2-3 cm from the case`s side

My Scythe Ninja is ~0.5 cm outside the case, it's a bit hard but I manage to put the side-panel on... :p
 
the top of my heatsink is about 1.5 inches away from the side panel, i wonder how close it will be in my new case
 
OC_LeGeND said:
and heres the 747 jet engine i mean my cooler for my celeron D ...
celerondcooler0ws.jpg

yea that's because all LGA775 coolers are freaking vacuums. The only viable quiet solution is the zalman7700cu or al/cu, which are the only ones in the series to fit the 775 socket type. Downside of course is that the thing is fucking ridiculously huge, but its quiet :cool:
 
board2death986 said:
yea that's because all LGA775 coolers are freaking vacuums. The only viable quiet solution is the zalman7700cu or al/cu, which are the only ones in the series to fit the 775 socket type. Downside of course is that the thing is fucking ridiculously huge, but its quiet :cool:
Incorrect... any of the Zalman flowers will fit with the proper LGA775 adapter. Even then, they're not the best solution out there.
 
I(illa Bee said:
you bought it because its blue didnt you!

lol, yea. I had to!

Prior to the TT Orb II, I had an SI-120 & Panaflow m1a.. Great setup, but it just looked out of place. I had to go with something that fit my theme a bit more. Because I'm running at stock temps, I won't lose or gain anything between the two setups.
 
heres mine.. its an AC Arctic Freezer 64 Pro.. I had a Zalman 7000B AlCu, wasn't happy with its performance:noise


the fan is very quiet.. I sometimes lower the fan speed to 60% so I cannot hear it at all =D
yay for silent PC~ :D
 
I bought one of those, and for me it is more noicy than my retail-cooler... :p Atleast at full rpm..

Edit: I have to go down to 35% to make it silent, and then the performance is everything but OK... CPU went over 59°C full load after a few minutes so I don't trust it at low rpms... :/
Atleast I am not satisfied with it, good that someone is. :)
 
this is the system in my sig, more details are there.
everything (including north and southbridge chips) is thermalpasted with arctic silver ceramique.
video card on a zalman vf700-cu led idles at 33 and loads at 57 max. that's down from 39 and 67 with the stock cooler and in my coolermaster centurion mid tower with the fan at 89% speed (VERY LOUD). also, the ram sinks on the card are aluminum ones that came with a Titan brand copper cooler that I put onto the northbridge. they are about twice as big as the aluminum ones that zalman provides.
my A64 3000 venice overclocked to 2.4ghz @ 1.45 volts on a thermaltake golden orb II idles at 28C and after ten minutes of the maximum heat/power torture test in prime 95, its highest temperature was 41C.

this processor does 2.6 @ 1.5 volts, but I like to keep my overclocks a bit under the max that I can get.

and the golden orb actually comes with a pearl finish on the blades of the fan as you can see in the pic below, it gives a swirly, almost spinning backwards effect when its on, and looks pretty when its off.

xqpack2.jpg
 
I just took of the cover on my 7800GT copper HS (evga) and put a 20dba 80mm fan over my videocard, temps are a woppin 11c cooler than the stock fan/HS, and 3c lower than the Nv silencer I had on there.

If i use a slim 80mm fan I will have enought clearence for SLI on my DFI baord (1 PCIe in between the next 16x slot)
 
Here is my heatsink.

dsc019599gp.jpg


Most over-rated pile of crap ever. Worst finished base. 41 idle, 65 load. Re-seated multiple times, same. Don't buy it.
 
Opteron 146 OC'd to 2.4, 1.4v. That heatsink is so bad, I can't even run at stock speeds. Not to mention the thermal probe doesn't work, and it always spins at slowest speed.
 
Send that piece of shit back man. Make them refund everything you paid, including shipping. If that proc is a s939, buy a Thermalright XP90 or XP90C. They are amazing.
 
revenant said:
bbq - Maybe lap the bottom? might help.

I think lapping would take off 3/4 of the base.

Send that piece of shit back man. Make them refund everything you paid, including shipping. If that proc is a s939, buy a Thermalright XP90 or XP90C. They are amazing.

It's going back tomorow.


And I have an old Zalman CNPS 7700, swapped for a silverstone FM121 fan, which works suprisingly well. 32 idle, 48 full load, with a capacitor-started 12/5v, so it starts off and then idles continuosuly.

EDIT #1: Here's a picture of the base.
dsc019608df.jpg


The picture doesn't show it, but the grooves are face-milled in at least .5mm.

The only reason I bought this was because it was Recommended in the Sticky at the top. Please, remove thisi piece of shit before anyone else wastes their hard earned money.
 
I(illa Bee said:
I just took of the cover on my 7800GT copper HS (evga) and put a 20dba 80mm fan over my videocard, temps are a woppin 11c cooler than the stock fan/HS, and 3c lower than the Nv silencer I had on there.

If i use a slim 80mm fan I will have enought clearence for SLI on my DFI baord (1 PCIe in between the next 16x slot)

yeah dood. I did that with the sli'd 6800's that I used to have. loved that cheap 10c drop! just goes to show that those heatsinks are actually pretty good, they just need more airflow.
 
ok, well to start it off here is my sempron with its his off:

IHSremovedLarge.jpg


then moving on here is my mobo with my zalman 7000 cu and zalman passive northbridge sink, notice that i had to dremel off a couple fins on the northbridge sink to make it fit along with my x850xt. the 7000cu keeps my sempron idling at 30 degrees and about 45 under full load doing 2700mhz @ 1.55V.

P1010193Large.jpg


since i removed the ihs i had to do a little modding on the 7000cu to make it fit properly on the core, you can see the little tab i added here:

P1010197Large.jpg


now moving on to my video card, heres a couple shots of it just after i installed the vf700cu:

P3220325Large.jpg

P3220324Large.jpg


unfortunately i dont have any shots of the whole setup right now, but its not all that hard to picture it all together. i run the vf700cu on a rheostat doing about 5V when im in 2D and then up to 12V in 3D in order to keep it silent when im not gaming.
 
Back
Top