Setup guides regarding some specific components requested...

ahmadka

Limp Gawd
Joined
Jul 11, 2006
Messages
136
Hi guys...well, hopefully, my new PC parts should be arriving in a few days now, so I thought I should do some revision, on how the fitting goes for the specific items that I have ordered...

The items I have ordered are listed in my Profile....

I am specially looking for an installation guide for the casing: Aerocool AeroEngine II Casing....

Also I have some basic questions regarding my first build:

1) Can someone please tell me the difference between the S/PDIF in/out connectors and the 6 colourful connectors, all on the port side if SLI-DR..

2) It has been mentioned that its better to assemble the motherboard outside first, and the move it into the casing.......if I do this, the components attached on board might get sudden movements/jolts when I am shifting about the mobo inside the casing, to fit it in....wouldnt these movements cause harm to the components attached ??

Thanx in advance....

EDIT: Also, if you happen to have manuals (preferably in PDF format) for any of these items, please send them my way :D...
 
have a look at the standoffs coming with the Aerocool AeroEngine II casing (the big ones on the left):

aerocoolstandsyk2.jpg


I can figure out that the ball type side goes into the casing, but how to do fix the motherboard onto the plat side ?? it sticks on or something ?
 
There are standoffs in the baggie. Those screw into the mobo plate of the case, and the mobo is attached using those standoffs via screws.
 
OK, my stuff will hopefully arrive tomorrow (finally!!) and so I have just a few last Q's:

1) Is it recommended to do run Memtest in the initial boots of the system to check the RAM for errors ? Cant it be done once the computer is fully assembled ?

2) Also, how long does it take you guys to build a complete computer from scratch ??

thanx in advance..
 
it really just depends on how hard it is to run cables.
takes me about an hour to get cables to where i'm fine with them.
 
1) You can run it whenever. I dont normally run it until im testing my overclock settings, lol.

2) If its your first time, it'll probably take you an hour and a half or so to put all the hardware together. I've built a computer in 10 minutes, but I usually take my time and take about an hour. I guess keeping all the cables neat takes a while, hehe.
 
hmm... ok thanx for the suggestion guys...

wont update the bios right now then hopefully

OK, the good news:

The stuff has arrived !!!!!

also..

My Exams have finished !!!


:) :)


Q.1

regarding memtest, i thought of a slight alternative..

you said that memtest should be run to check the RAM *before* installing windows, etc...

so I just want to confirm...that memtest is performed AFTER you install everything into the casing, but BEFORE you install any OS..Right ??

And if this is the case, then that means that the longer job is the memtest job, since it requires overnight activity...but the stuff before that is pretty much hands on work right,,...which should take like 4-5 hours for me I guess...

Q.2

Also, are the RAM timings the only setting that needs to be set in BIOS, other than the basic stuff (memtest setting, boot sequence, ESCD, cant think of anything else)..??
 
OK....well....got some news for ya....

ITS ASSEMBLED, AND
WORKING !!!!


HOOOOORAAAYYYYY
!!!!

​


Well, its official, AhmadKA's Dream PC is Live 'n' Kickin' *** !!! First, I would like to thank each and everyone of you, for helping me out is soo many different ways !!! Thankyou for putting up to my questions, and thankyou for guiding me through !! Thankyou VERY MUCH !! I am VERY HAPPY today !!

Also, in case you are wondering, I did not actually do the installation myself. I planned to bring this computer technician from my uni, who could help me out in installing all the stuff. In the end, he ended up doing all the hands on work lol :D .... I just pointed out stuff my the guides here and there, and watched over what he was doing ...

Hey, check out the pics I took with my camera, during the installation and the final result:

http://rapidshare.com/files/9131741/MyDreamPC.rar


Anyways, I am now gonna give a detailed log of the entire installation procedure, and then will ask some questions...

Contents:

1) The Procedure that was followed..
2) Some slight 'glitches' that I have detected..
3) Some Questions..

Let's begin:

Log:

Key:

Black means the step was done as in the procedure (A guide I got from DFI because of the DFI board)
Blue means an additional step that was performed, which was NOT included in the procedure
Red means a step, that was included in the procedure, was missed out !!
Magenta Means some information about a step, etc...
Here we go:

1. Familiarize yourself with how to assemble a PC generally, including:
http://www.mysuperpc.com/build/pc_parts_list.shtml
http://www.buildyourowncomputer.net/learntobuild.html
http://www.motherboards.org/articles...des/924_1.html
http://www.build-your-own-computer-tips.com/
2. Place motherboard on insulated surface (on wood table and pad shipped with motherboard)
3. Inspect and prepare motherboard, adjust jumpers as necessary.
4. Install CPU and heatsink.
5. Install 1 stick RAM in slot 2 (Magenta, closest to edge) We installed
both sticks at the same time.

6. Install video card in top (closest to CPU) PCI-E slot.
6.b.--> PCI-Express Power Connector was connected to the VGA Card.
7. Connect power supply to motherboard – be sure to make all four connections. (A minimal install outside the case is optional. You may wish to jump to Step 10).
8. Connect monitor.
9. Connect keyboard and mouse.
10. First boot – use EZ Touch Power Switch on motherboard to turn power on. To enter BIOS, press DEL before the fourth diagnostic LED turns off and the DFI LanParty splashscreen appears. Load Optimized Defaults/save and exit.Only Motherboard was tested to work!
11. Install mobo and I/O shield in case.
12. Connect case and CPU fans to motherboard.
13. Install power supply (can be done before Step 11 if you prefer).
14. Connect power supply to motherboard – be sure to make all four connections.
15. Connect front panel connectors and case fans to motherboard.
16. Connect monitor.
17. Connect keyboard and mouse.
18. Second boot. Enter BIOS. Set Update ESCD/will update DMI pool.
19. Install hard and optical drives.
20. Third boot. Can turn off Update ESCD.
21. Press DEL to enter BIOS
22. Input BIOS settings for RAM..
21.a. Load Optimized Settings
21.b. Change Date/Time
21.c. Change Boot order

23. Fourth boot.
-------------> Currently Over Here !!! <--------------

​
Summary

As you can see from above, two main steps were NOT performed, ESCD setting were not changed. RAM Timings were not changed....

Glitches/Problems I Noticed...


1) During installation, we tried installing the floppy drive, but the space in the bottom smaller compartment was a bit too small, and the floppy drive was not fitting in. Result: We did not install the Floppy Drive.... Glitch: By mistake we placed the Aerocool shield, upside down !!

2) Problem: The Power LED is turning on fine, but the HDD LED is NOT turning on. Possible causes could be
  1. LED was not connected at all.
  2. LED was connected on the wrong pins..Can this be dangerous ?
3) Errors Received on computer startup:
  1. Something that went like 'Set CPU Frequency in CMOS'... Result: We tried restarting the PC, this removed this error, but now we got this second error:
  2. Something that went like 'BBS Boot Sequence was changed' ... Result:We went into the BIOS and did steps 21.a. 21.b. 21.c. above....it removed the error...
4) Glitch: I noticed the front 140mm fan was wobbling a little bit....I don't know if that is the way it is, or if there is a problem...

5) Glitch: The Power LED, is showing some behavior I have not seen before:
  1. When I power on the system, the light turns on a little later, around when the LAN Party Logo is shown...not before..
  2. When I switch off the system, by holding down the power button down for 5 seconds, the power LED turns off immediately as the 5 seconds time starts..and then at the end of the 5 seconds, the LED just blinks for a split second, and then turns off with the system itself....... Is this normal/dangerous?

5) Glitch: I read somewhere that when you install memory in dual channel, it is confirmed at system startup....that is, the memory is written as '-------- Dual Channel Memory'..but in my case, although the RAM is correctly detected (2GB), it does NOT say whether its Dual Channel or not.....How do I check if the system detects the RAM as Dual Channel or not ?

Questions:

Main Question: What do I do next ? Do the ESCD stuff
I missed above ? Run Memtest ? Fix any of the above Problems (mention how please)..? What should I do next ?


Also, thanx again everyone :rolleyes: :p :cool:
 
Guys, I have made a little video, showing some of the errors/glitches/problems I discovered during the installation....

Here is the link:

http://rapidshare.com/files/9160932/GlitchVideo.rar

Also, the CPU Frequency error I talked about above, which went away after using the 'Load Optimized Settings' option in the BIOS...is back...

I don't know why this error is showing again. I just restarted the system a couple of times, and this error just reappeared out of nowhere !! This error is shown in the video..

Please have a look at the video..

and tell me what should I do next ? Set RAM timings ? Run memtest ? ... Waiting for your input...
 
OK, i tried turning around the HDD LED cable to see if the HDD LED comes on...it WORKED !! :D

Regarding the CPU Frequency error...i didn't reset the CMOS...instead, I just selected the 'Load Optimized Defaults' option in the BIOS again...I hope the CPU Frequency error does not reapper this time hopefully...

Regarding Memtest...

I decided to run memtest, so I went into the BIOS and enabled it...Memtest is running right now....but I have a few Questions.. have a look at this pic of the PC running Memtest:

1001434ts6.jpg


Somethings to note down are:

1) RAM timings are more or less automatically detected...I have DDR500 3-4-4-8 RAM, whereas the system detects it as DDR401 3-4-4-7

2) Also memtest is indicating that this is Dual Channel :)

3) The Memtest version is 1.55, whereas the latest is 3.2 (which I also have on CD)...so isnt it better that I run the CD version ??

4) You guys pointed out that I should run tests 5 and 8....but when I go into the test selection menu of this Memtest 1.55, I just see a max of Test 5...the 6th option is the (0) Continue option ......probably version 3.2 has more tests available...

Lastly, I have noticed that the PC keeps making this very slight split-split second sound...it is like a crackle....the PC makes it like every 2-3 minutes in the start.........i think it is probably because the temperature inside the casing is gradually rising, so the motherboard is slightly expanding :eek2:....this happens with the heater in my room as well :p......also I am guessing that this is the reason since the crackle sound only comes when the system is on...

awaiting replies....thanx guys :D

EDIT: but Memtest is saying the CPU is AMD Athlon 64..whereas its actually AMD Opteron 165....bug in the program ?
 
Back
Top