Router Problem

krazykrook

n00b
Joined
Jan 8, 2005
Messages
15
I dont have that much experience with routers but here goes.

Current set up:

ISP --> linksys router --> Switch --> All computers
This router is blocking certain ports that I wish to use so I bought a new router to put in front of the old one and connect my computer to it.

Desired setup

ISP -->D-link router (to my computer) --> Linksys router --> Switch --> All other computers

The linksys is DHCP, but we manually config our IP's for our pc's. When i hook up the dlink and configure it to DHCP I get internet. But the internet doesnt go through to the other router (to the other computers).

When I connect my computer to the dlink with the ISP still going to the lynksys ( ISP --> Linksys router --> Dlink router/Switch --> All other computers) I am able to access the other computers. But when the ISP goes to the Dlink (Desired Setup above) I cant access the other computers.

Is this because Dlink is 192.168.0.1 and Linksys is 192.168.1.1??? I dont see why this isnt working. I dont want to reset the Linksys router because I am trying to make this a secret and cant remember the configuration of the linsys.

Bottom line, Im trying to the the second setup (Desired setup above) to work with internet to everyone without having to reset the linksys router.

Any Ideas How to make this work? I am stumped
 
What possible reason do you have for using two routers? Just use one or the other. Not sure why you want it to be a secret, but you can just configure the new router the same as the old. If you can't remember the configuration of the old one then just log in and check it. Write down the settings and copy them over to the new one.
 
Thats the thing, all I know is that the linksys is setup as dhcp and thats basically all I know except for the ports to forward. See, the linksys is blocking certain ports that I want to use, I dont want the person controling that router to know I am accessing those ports now. So bought this dlink router and thought it would work, but there is always a catch

Also, the dhcp server is disable on the linksys. I click the disable bubble for dhcp server on dlink and apply. Then click status and still says dhcp server enabled.
 
If the linksys is forwarding ports to clients behind it then you probably are out of luck, as you have a double NAT situation going on, and that can cause havoc with port forwarding and such. IOW, whoever is relying on those forwarded ports would figure out pretty quickly something is up. Not a whole lot you can if you don't have control over the network and can't work something out with the person who does control it. Though if your ISP will give you two IP addresses, you could just hook up a switch to your ISP's line, and hook yourself and the linksys router up to the switch. You'll both get public IP addresses and you'll be able to do whatever you want.
 
hmm, I tried hooking up the netgear switch I have to do the exact same thing you are talking about but, it doesnt have firmware so it cant distribute internet. What kinda switch do I need that would make this work? Does it have to have VLAN? dont even know what that is.
Here is the switch that wouldnt work for that, that I currently have
http://www.newegg.com/Product/Product.asp?Item=N82E16833122004
 
I think you might be confused as to what a switch does. A switch just concatenates nodes; they don't perform any routing functions(most switches don't). If you hook yourself and the other router up to the switch and the switch up to the internet, and only one device gets an IP address, then your ISP is only giving you one IP address and that setup won't work. Unless you wanted to pay for another IP address.
 
I remember when I had the Isp --> switch --> my computer and it didnt work, no internet. So you are saying if there was a router after the switch it would work? and any switch works for this?
 
krazykrook said:
I remember when I had the Isp --> switch --> my computer and it didnt work, no internet. So you are saying if there was a router after the switch this would work? and any switch works for this?
That's most likely because your ISP's dhcp server still has a lease out for the router's MAC address. Once that lease is released, you should be able to get an IP address. Still, though, that does no good since apparently you can only have one IP address.
 
If I had another linksys router (so the ip's would be the same 192.168.1.whatever), then would this work? Just like this setup except a linksys in place of the dlink
ISP -->D-link router (to my computer) --> Linksys router --> Switch --> All other computers
 
krazykrook said:
If I had another linksys router (so the ip's would be the same 192.168.1.whatever), then would this work? Just like this setup except a linksys in place of the dlink
ISP -->D-link router (to my computer) --> Linksys router --> Switch --> All other computers
I don't see how that would make a bit of difference. Isn't the router's IP address configurable anyway?
 
jpmkm said:
I don't see how that would make a bit of difference.
I am thinking that if the IP's for each computer were set up the same 192.168.1.whatever# vs. the dlink which is 192.168.0.whatever# it would work. Ex. when I was connected to the dlink, I have to have an ip like 192.168.0.103. For the linksys I would have to have 192.168.1.103 for it to work. That is what I think the problem is, but I consider myselft a noob to this so have douts
 
Back
Top