Problem with ATI Radeon 9800 Pro installation - blank screen

nghtfx

n00b
Joined
Jun 8, 2005
Messages
22
Hey everyone. I recently decided to upgrade my computer, so I bought a 9800 pro and some ram, (which i bought PC133 instead of PC100, DOH! gota exchange it)

My current PC stats (stock compaq.. got for $60, don't laugh :D )
900Mhz AMD Athlon Processor
128mb PC100 Ram
40 gig HDD


Ok now on to the problem:
I popped out my old video card and stuck the new one in, and hooked the male side of the cable onto an extension coming from the cable hooked to my CD rom, and the computer booted up fine. (There was female end cable also on the card.. do both need to be attached? I only had one cable end that would work). I put the driver CD in and began to install the drivers, when my screen went totally black, and a cursor started blinking in the top left corner. Ctrl+alt+delete, alt+tab, alt+F4... nothing worked, so I was forced to do a cold reboot. I checked the connections and everything seemed snug, so I tried again.. after about 2 minutes of the computer running, same thing happened. After about 2 more reboots I gave up. Any advice as to how I can fix this? Or even what is causing it? :confused: :confused:

Thanks in advance :)



//edit I hope I posted this in the right forum.. if not, mods feel free to move it
 
nghtfx said:
Hey everyone. I recently decided to upgrade my computer, so I bought a 9800 pro and some ram, (which i bought PC133 instead of PC100, DOH! gota exchange it)

My current PC stats (stock compaq.. got for $60, don't laugh :D )
900Mhz AMD Athlon Processor
128mb PC100 Ram
40 gig HDD


Ok now on to the problem:
I popped out my old video card and stuck the new one in, and hooked the male side of the cable onto an extension coming from the cable hooked to my CD rom, and the computer booted up fine. (There was female end cable also on the card.. do both need to be attached? I only had one cable end that would work). I put the driver CD in and began to install the drivers, when my screen went totally black, and a cursor started blinking in the top left corner. Ctrl+alt+delete, alt+tab, alt+F4... nothing worked, so I was forced to do a cold reboot. I checked the connections and everything seemed snug, so I tried again.. after about 2 minutes of the computer running, same thing happened. After about 2 more reboots I gave up. Any advice as to how I can fix this? Or even what is causing it? :confused: :confused:

Thanks in advance :)



//edit I hope I posted this in the right forum.. if not, mods feel free to move it
Guess what? You have an issue between the card and the mobo. The AGP slot on that old Compaq mobo is only AGP 1.0-compliant (AGP 2x maximum), and likely cannot handle the current draw the 9800 Pro requires. And even though the BBA 9800 Pro is classified as a "Universal AGP 3.0 Card" (which means that the card will physically fit an early 3.3V AGP 1.0 slot and theoretically work on such slots), the 9800 Pro GPU supports only 0.8V and 1.5V signaling. Hence, the stability problems on older 3.3V AGP slots.

Also, did you uninstall the drivers for your old video card from your PC? Having drivers for both your old and new video cards installed in the same PC at the same time can also cause such problems.
 
*smack head* I didn't even think about AGP .. ugh. I feel like an idiot lol. I've been out of the swing of things with computers for a few years now, and I am trying to rekindle my knowledge slowly but surely.

I didn't uninstall the old drivers first - which could have been part of the problem. However, after a minute or two of running w/the card in, the card became warm to the touch. This is probably due to the incompatability of the agp settings?
 
nghtfx said:
I didn't uninstall the old drivers first - which could have been part of the problem. However, after a minute or two of running w/the card in, the card became warm to the touch. This is probably due to the incompatability of the agp settings?
Yep, it is definitely an incompatibility of the AGP voltage settings. The card is receiving too high of a voltage, causing the card to potentially overheat. Thus, your 9800 Pro will cut off the video output - enough to force a hard restart - to prevent further damage to the card.

On the other hand, running a high-voltage AGP card on a slot that can only deliver lower voltages will prematurely burn out the AGP slot because the higher-voltage card will draw far more current from the lower-voltage slot than the lower-voltage slot can handle.
 
E4g1e said:
Yep, it is definitely an incompatibility of the AGP voltage settings. The card is receiving too high of a voltage, causing the card to potentially overheat. Thus, your 9800 Pro will cut off the video output - enough to force a hard restart - to prevent further damage to the card.

On the other hand, running a high-voltage AGP card on a slot that can only deliver lower voltages will prematurely burn out the AGP slot because the higher-voltage card will draw far more current from the lower-voltage slot than the lower-voltage slot can handle.

Good to know, thanks a lot :D . Gona ship this one back to newegg.com now! lol.

I am glad my friend recommended this forum to me.. you all seem to really know your stuff :D
 
Back
Top