Problem installing NVRAID on Asus A8N E motherboard

Braznor

n00b
Joined
Sep 17, 2005
Messages
9
Hi guys,

I'am trying to setup RAID 0 on my computer, but I'am unable to do so. I have the Asus A8N E motherboard (Note: not the SLI version) This motherboard has just the Nvidia NForce4 RAID controller on it, it does not have the SiliconImage RAID controllers.

What happens is that when I setup the motherboard and the HDD devices to enabled in the BIOS and also the RAID array (by pressing F10 key during boot) to Strip in RAID 0, I'am unable to reinstall windows on the computer.

I have two Seagate 7200 RPMs HDDs (model nos:ST3160827AS ) I plan to use as the RAID 0 drives. After I configure the computer to the above steps and set the computer to boot from the windows XP disk, the computer gives me the message "PRESS ANY KEY TO BOOT FROM THE CD" Then when I do so, i get the following message that "SETUP IS INSPECTING YOUR COMPUTER CONFIGURATION" Then after this point the screen goes blank and the setup does not continue.

I am able to reinstall windows normally without RAID and everything else works fine. No BSODS or anything. It is just that I'am unable to setup RAID on my computer :confused:

I have heard that the NVRAID controllers had problems initially, do I need to update the BIOS to fix this????


My system specs are as follows:

AMD Athlon 64 3500
Asus A8N E motherboard
2 GB DDR 400 MHZ RAM
XFX 7800 GTX @ 490 Mhz core and 1.3 Ghz memory
Seagate 160 GB SATA 7200 RPM * 2
Sony 16x DVD RW

Please help me guys, I desperately need help with this issue. :(
Thanks for everything.
 
Do you have the boot priority set up properly in the bios to pick up the raid drives? ....scsi/raid? Sounds like it's not 'seeing' your drives at all. Check the boot priority in the bios - and while you are there make sure the bios sees your drive/s.
 
Thanks for replying, zone_86 :)

I finally have RAID setup on my computer, but there are still some issues with it

First I updated the BIOS to the latest version 1008, formatted both the HDDs and then was able to setup RAID 0 using the Nvidia RAID driver diskette. But I received two files missing error message while the setup was copying files. Now the problem is that windows does not shutdown automatically. The system hangs up on the screen " WINDOWS IS SHUTTING DOWN" However the RAID setup was succesful. The MY COMPUTER screen shows just a single C: drive icon with the correct size expected.

My question is that whether the RAID driver diskette I created was defective and whether this is causing the problem with Windows not shutting down????

I suspect this so, because while it hangs up on the " WINDOWS IS SHUTTING DOWN" screen, the HDD activity LED is blinking in short pulses once or twice a second. Perhaps installing the latest chipset drivers from Nvidia or creating the latest RAID driver diskette with them would resolve the issue????
 
Make a driver diskette from the 6.53 NF4 drivers when you're installing windows. It's 1 folder, and I've seen lots of posts including myself have this issue when using the SATA drivers from the 6.66 set.

And after you get into windows, you can install the 6.66 drivers, but I don't recommend installing the IDE drivers as again lots of ppl have trouble afterwards with them.
 
I had a really bad time loading XP on the updated RAID drivers. This was my process:

Make floppy off included driver CD for RAID drivers.
Install XP to array.
Load latest 6.66 Nforce drivers.
Update to BIOS ver. 1009.001 beta
Continue as usual, be completely unimpressed by onboard sound.

Everything has been rock solid after this process. Using the new drivers prior to the BIOS update wouldn't even allow XP to boot after loading. My only issue with the beta BIOS is that sometimes I simply can't get into BIOS setup. But for system stability it's been very nice.

Unrelated note: The onboard sound is horrible. Anytime a rich sound with a decent amount of bass occurs it crackles and pops. Back to Audigy for me.
 
Back
Top