Please help me get a higher overclock :| Opteron 170

MrSuge

Limp Gawd
Joined
Oct 17, 2006
Messages
212
My rig is in my sig but i'll just get the basics down

Biostar TForce4 SLI
7950GT KO
2gb (4x512mb)
Antec SP500 PSU
P180B

So far I've gotten 260 x 10 = 2.6ghz
5:6 memory divider
stock voltage

anything higher and my bios says "running in safe mode, reset cpu frequency" :confused:

I can go higher with an increase in voltage but would like to maybe reach 265/275 w/out a voltage increase...

Here is a screen shot of temps, cpu-z cpu + cpu-z memory...hopefully you guys can get me going in the right direction :cool:

 
There is no other way to overclock your chip more other than increase the voltages. so Increase the Voltage!!!
 
bail_w said:
There is no other way to overclock your chip more other than increase the voltages. so Increase the Voltage!!!

Aww man :(

So you're saying 2.6 is just about the limit at stock voltage? If so then I'll def increase the voltage but if there is a way to get just a tad bit more out of stock voltage to maybe 2.65/2.7 that would be killer! Again I'm a noob and I'm just hoping I'm doing something wrong which is holding me back @ 2.6 that you guys could figure out.

Thanks!
 
go for broke or go home
this is the [H]ard way of life...

give it a bump to ~1.5v and see what she can do. as long as temps are fine, screw it. also, dont be afraid to drop some more juice to the ram in a effort to tighten those timings or get a higher clock there as well...
 
If you haven't done it yet, I'd suggest you find the max your ram can do at those timings. Put a lower multi on your 170, and see how high you can raise your fsb. If you can take your fsb to over your current 260, it's your cpu and you need more voltage.

It could be your memory controller that doesn't like 4x512 sticks with a cas of 2.5.
You could try 3-3-3-8-12 on your timings.

It helps alot to find the max your board, cpu, and memory can do, testing one at a time.
 
you dont need to bump the voltage all the way up to 1.5 as fubar suggested..yet. start off by goin up to like 1.35 or 1.36 and see if that helps.
 
So my ram is horrid...but what did I really expect from 4x512mb. I might take 2 out and see what it gets then but 2gb is so smooth!

Okay so I got it @ 290 x 10 orthos stable > 30min @ 1.4v

BUT I had to bring the memory to 1:2, or 100mhz :( It's running @ 145 or something

The highest I can go with the memory @ 166 (212) is 2.6ghz

So what's better. Going with the raw processer power @ 2.9
or
having the memory speed > 200 but the cpu speed @ 2.6 stock voltage

Temps are about 44 under load and 34-36 idle for 2.9 and 41/32-33 for 2.6
 
In the A64 realm.... CPU speed is KING.

edit... but try to keep your RAM as close to 200 as possible (if it won't keep up with the CPU FSB)
 
I could get 2.75 on a 133 divider with 1.375 volts. Haven't seen if it's orthos stable. That is about 183 overclocked. Will try to play around more. I too would like it to reach 200 even. I think If I just run 2x512 I'll be able to hit 2.7-2.8 @ the 166 divider which is just about 230 - uhh now I highly doubt that. My ram sucks...it's generic but has samsung memory chips and someone on here said it's supposed to clock decent.

But does it matter if it's currently running @ 145 using the 100 divider? Would it have a large negative effect? Or would it not even be noticable and the cpu will take over?
 
I agree with everyone else, you gotta bump the voltage. And you should try getting 2x 1gb ram sticks of good overclockability.
 
-definitely bump the voltage , up to v1.55 , depending on your temps
-set the command rate timing to 2T or disabled ,
-use 3-3-3-8 ram timings
-use the 133 ram divider
 
Your chip is pretty good if it can do 2600 at stock. Mine caps out at 2580 on watercooling at stock. Remeber that your ram dividers may not show up when you change the multiplier in the bios. For example on my Bios if I have it as 280 x 10 and try to change the divider, my only increments are 140 and then 166. But then if I set the multiplier to 9x and save, reboot suddenly the 150 divider is now available. I have no idea what that's about.

I run 300 x 10 or 330 x 9 at my stock timings of:
3/3/2/8 just under my 250mhz ram ratings (166 and 150 dividers respectively)

Certain ram dividers just simply wont work well on my system, even though they are lower mhz than the next faster divider (which happens to be faster and more stable).
You should just go straight to 1.525 - 1.550 and keep pushing forward. An easy way to do this is to run "Systool" stability test while you gradually bump the fsb up in 1 mhz increments unitl you see it fail. You can quickly find out the end limits at given voltage. If I go over 1.550 my chip's performance actually becomes less stable. 1.550 should be your max on air anyhow.
 
Back
Top