Please Help - literally building my PC right now

Joined
Dec 14, 2006
Messages
59
I had a thread a while ago where everyone here was very helpful in helping me choose which parts to order. I have never built a PC before though and just got almost all the parts today.

I just placed the processor (C2D E6400) into the motherboard (Gigabyte GA-965P-S3) socket exactly as the directions said in the processor manual. The processor socket lever required quite a lot of pressure after the chip was in there to close it, I know it was lined up correctly (had arrow facing the indented corner of the socket plus the pictures in the manual showed the same way) so was it suppose to require a relatively large amount of force?

Up until this point the mobo and processor manual have been the same, however the processor manual tells me to install the heatsink "with the MOTHERBOARD INSTALLED IN THE CHASSIS" (caps and all) while the motherboard manual tells me to do it right after installing the CPU before I place it inside my case (Cooler Master Centurion CAC-T05). Should I follow the big capital letters and place the heatsink in AFTER installing the motherboard into the case?

On the same token, should I install the RAM before placing the mobo into the case? I have installed RAM before into my past mobos while it was in the case so I assume doing it beforehand would just be a step of convenience.
 
Can't help ya with the the lever pressure - I haven't built a C2D yet. On all my builds, the lever pressure was noticable, but not difficult.

My process:

0) ground self
1) Mobo on foam
2) processor in Mobo
3) HSF on processor
4) RAM in Mobo
5) connect case jumpers (if they're long enough - power, reset, hdd LED, front case ports, etc)
6) install mobo in case, including connecting case jumpers if you haven't yet done it
7) connect drive cables
8) install vid and other expansion cards.
9) test
10) clean up cabling (though I'm not a fanatic about it like many here)

Note that I have already installed the drives in the case before I start mucking with the motherboard.

BB
 
BB Gun said:
Can't help ya with the the lever pressure - I haven't built a C2D yet. On all my builds, the lever pressure was noticable, but not difficult.

My process:

0) ground self
1) Mobo on foam
2) processor in Mobo
3) HSF on processor
4) RAM in Mobo
5) connect case jumpers (if they're long enough - power, reset, hdd LED, front case ports, etc)
6) install mobo in case, including connecting case jumpers if you haven't yet done it
7) connect drive cables
8) install vid and other expansion cards.
9) test
10) clean up cabling (though I'm not a fanatic about it like many here)

Note that I have already installed the drives in the case before I start mucking with the motherboard.

BB

Should I install the PSU before putting the Mobo in the case also? So far I've:

1. Placed Mobo on foam on desk (didn't want to place it straight on desk and bend all those little pin things in the back)
2. Placed and secured Processor into Mobo
3. Installed RAM into Mobo
4. Installed PSU into case

I will have the video card tomorrow (I don't have a PCI-e card or an old PCI card to put in right now) but I'd like to have the whole thing in my case and plugged up when the card gets here so I can go ahead and put it in and start the whole Windows installation.
 
Ok, I am lost now, the case comes with TONS of screws... which ones do I use to screw in the motherboard? Do I use any of the ones that are long enough and fit through the board? Do I need to use these little gold connectors somehow (look like mounting screws)?

screwsjr2.jpg
 
Houston3000 said:
which ones do I use to screw in the motherboard? Do I use any of the ones that are long enough and fit through the board? Do I need to use these little gold connectors somehow (look like mounting screws)?

Those are called standoffs, and the go between the case and the mobo, to prevent the mobo from shorting. Install the standoffs in the appropriate holes, and then set the mobo on top of the standoffs and secure the mobo with the correct screws.
 
It probably says to install it while its in the case because the temptation to use the HSF as a mobo handle is hard to resist. With these current Intel HSF's, its VERY easy to dislodge the HSF, hence the recommendation in the manual. You could do it either way, in or out of the case, just be careful to not dislodge the HSF while the rest of the build progresses. If its not sitting properly, it will either not boot (shutdown right after powering on) or run rather hot (idle temp in bios should be under 35°C; if its higher, reseat HSF). Yes, install the PSU before installing the board.
 
Thanks for the help so far guys, I've been working on and off in it all day (no video card until tomorrow anyways). I have the motherboard screwed into the case with the standoffs and it lines up nice and pretty with the back I/O ports. The processor w/ heatsink and RAM are installed and the PSU is screwed in along with my Hard Drive and a single DVD drive. Right now my main issue is with the Front Panel wires... wow they're confusing.

The front case wires are labeled as such:
Power SW (2 pins)
Reset SW (2 pins)
Speaker (4 pins)
H.D.D. LED (2 pins)
HD Audio (10 pins)
AC' 97 (10 pins)

As well as these there is a green/white wire with the green reading + and the white reading - both 1 pin each. As well as a rats nest of 10 tiny individual 1 pin wires coming off AC' 97 and HD Audio plugs with a sticker that says what each one is (Yellow-MIC, Black-AUD GND, Green-RET-R, etc...)

On the motherboard's F Panel (Front Panel) the pins are labled:
PWR_LED (this label is over two sets of pins in an L shape 3 going down and 2 going across)
PWR (2 pins)
RES (2 pins)
SPEAK (4 pins)
NC1 (1 pin)
MSG (2 pins)
HD (2 pins)
F_AUDIO (10 pins)


I plugged "Power SW" and "Reset SW" into the PWR and RES pins respectively as well as plugged "Speaker" in the SPEAK pins. Where does the "H.D.D. LED" plug into; the 2 pin section of the "PWR_LED" or the "HD" pins?

I don't know what the MSG, NC1, or the 3 pin vertical section of the PWR_LED pins are for. For the wires I don't know what the +/- wire is for, maybe it plugs into the LED pins? Most of this is also confusing to me because my case doesn't specify polarity while my mobo does, for example the PWR pins on the mobo show positive on the left and negative on the right and the RES pins show it the opposite - however there is no -/+ indication on the wires themselves - the only difference is for each wire there is one colored and one white wire so I assume the colored is positive while the white is negative?

Other than those issues there is the case of the audio, do I plug in the AC'97 or HD Audio into the F_AUDIO pins? OR do I have to sort through the mess of single wires I mentioned attached to those two plugs and hook them in individually?

Please help :(
 
Well after rereading parts of my manual I found that the mobo is set to HD Audio by default as opposed to AC'97 so I plugged the HD Audio wires into the F_Audio pins, still don't know what all the individual wires coming off of those plugs mean though,

I also found that the PWR_LED pins are actually two separate sets of pins; the 3 vertical ones are for the Power LED and the 2 horizontal ones for the "Chassis Intrusion/Case Open" LED which I don't even think my case has. Unfortunately I have no plug to attach to the three pins for the Power LED so I don't know how that light will work. I plugged up the HDD LED wire to the HD pins I mentioned. The +/- wire I still can't figure out, I plugged them into the MSG pins, which, according to the manual, is "Message LED/Power/Sleep LED" (maybe a type of power LED?)

Anyone know something I don't?
 
Houston3000 said:
As well as these there is a green/white wire with the green reading + and the white reading - both 1 pin each. As well as a rats nest of 10 tiny individual 1 pin wires coming off AC' 97 and HD Audio plugs with a sticker that says what each one is (Yellow-MIC, Black-AUD GND, Green-RET-R, etc...)
I'm guessing that unlabeled wire is your Power LED. Trace it and see if it connects to an LED :p If so, plug the colored wire into pin 1, and the other into either pin 2 or 3. The individual pins attached to the Audio block plugs are there in case the mobo doesnt follow the standard pin layout and you need to rearrange where the leads plug in.

"negative," or "-" is also known as common. So, if all sets of wires have a different color and one common color amongst them, then the different colors are the positive leads (+), while the common color is negative/common (-).
 
Back
Top