P4P800 Voltages

Vs17

Weaksauce
Joined
Sep 24, 2003
Messages
83
After finally fixing my 2.8c P4P800 Deluxe setup I set my voltage to the default 1.525v in the bios (original, have not update yet). When I boot to windows however and use CPU-Z it reads the vcore at about 1.6v, though it fluctuates below that (around 1.55 - 1.6). I was wondering if CPU-Z or the sensors are just reading it wrong, if it really is at 1.6v, or if a BIOS update will help solve the problem. Thanks for the help...
 
no, the sensors aren't wrong. The p4p800 has some serious voltage fluctuations. I RMA'd mine b/c when bios was set to 1.52v, the actual voltage would range anywhere from 1.50v all the way up to 1.87v. smoked my 3.0c I had in it. Luckily I was able to RMA both. The 3.0c wasn't even stable at 3.0 after it spiked the voltage like that. It even had some problems at 2.8.

If it fluctuates more than that, RMA it. There's no reason to flood your cpu with un-needed juice IMO.

I bought an Abit AI7 to replace my P4P800 (will be selling the replacement I get from RMA)...and so far, the most my voltage has fluctuated was .01v. Very pleased with this board so far.
 
I get the same wandering voltage issue. Set to 1.525 and MBM records a low of 1.55, high of 1.6 and average of 1.57. I'm almost wondering if the BIOS isn't off by .5 in it's settings, ie 1.525 in BIOS = 1.575 to the hardware...
That being said, what are the chances that the BIOS is interefering? Maybe the automatic management of the power isn't truly getting turned off and it's just using the hard user setting as a base then altering it from there...dunno about that level of programming but I know in higher levels I could see a lot of people acidentally making this mistake without realizing it.
 
mine was an extreme. If my voltages didn't go above 1.6 when it was set to 1.52, I would have been fine with it...but seeing as how it shot up to 1.87v often and smoked my 3.0c in the process...it really pissed me off. Which is why I bought Abit. I did some checking and Abit seemed to have the most stable voltages on the AI7. Thought about going Epox...but it was out of my pricerange for the one I wanted :confused: :(
 
i had the same issue with my mobo. If vcore was set to 1.55 it would always go 1.6 and a bit above. Double checked in the hardware manager or something in the bios and that was actually what the BIOS was reading the voltage as and not just a misread by ASUS Probe. I actually never resolved the issue and was simply told that at 1.6 it should be ok. But that 1.8v, ouch that's way too much juice for the cpu.
 
1.7v and lower is fine
1.8v is just too high
i have mine set to 1.6v, goes as high as 1.68v and as low as 1.55-58
i can live with it though, i got a stable oc and thats all that matters
 
So does anybody know if they are any fixes at all, or if updating the BIOS will at least reduce the fluctuations?
 
nope. You can try a droop mod. That will keep the voltages from fluctuating between idle and load times (Asus seems to raise the voltage when the cpu is idle, and lower the voltage when the cpu is under load...seems kinda backward to me...but whatever).

Or if your board was fubared like mine was, there's no hope but an RMA.
 
its not just you guy's board that does it. Mine does too, it wanders a little bit, but I have never really worried about it. I think it may just be the sensor being off... hey it happens to thermal sensors too.
 
Originally posted by pbXassassinX1524
its not just you guy's board that does it. Mine does too, it wanders a little bit, but I have never really worried about it. I think it may just be the sensor being off... hey it happens to thermal sensors too.

It could be a sensor...but I measured mine at the mosfet legs. My sensors were pretty close to being right on....it was just the voltage regulator IC that was fubar'd.

although, now after running this AI7 for a few days, I think the P4P800 handled my ram a little better as far as timings go. This AI7 seems to be a bit sensative to various settings and hardware.
 
Mine doesnt wander much... its just high. I set it for 1.65v for my OC, and CPU-Z is at 1.72... I think I'm gonna bump back down to 1.6 just to be safe.
 
I've had a Willy in the P4P800 running at 1.85V for about a year and I've seen fluctuations all the way up to 2V. The board is making that old chip live a little bit too dangerously IMO.
 
Back
Top