P4C800-E BIO Flash NO BOOT!!!

Joined
Jan 28, 2004
Messages
538
My specs are as listed below except I'm running at stock speeds and I'm not using RAID 0. The first WD Raptor is my boot drive.

So I flashed to a new BIOS 1016 with the Auto Update utility and now my system WILL post but it wont boot into windows. I have the WD Raptor set as the primary boot device. The weird thing is that it isn't listed in the BIOS under Primary/Secondary/Third or Fourth IDE Master or slave. The WD is of couse an SATA HDD and I remember that it used to be shown there somewhere in the BIOS. However, the computer must be able to read the raptors because I can change which HDD I want under the Hard drive menu and select as the primary.

Whenever I try to boot I get a message saying "please select proper boot device or insert boot media into the device"

If anyone could help me ASAP I'd very much appreciate it because I have work that needs to be done and I really need to keep the data on both raptors as well as the Maxtor.

Thanks
 
Thanks for the help, but I couldn't get the system to boot so I can't get to the internet on my rig. Fortunately I fixed the problem.

However, I did read that you need Live Update version 5.22.02 which is the latest auto flash utility however, it's not listed on the ASUS site anywhere. I can download the Afudos DOS flash utility, but I am unsure about how to use the DOS flashing utility.
 
The instructions in your motherboard manual are actually pretty good. As far as the Live Update tool, I've had alot of problems with it.
 
Well I guess with the DOS flash you have to make a boot disk right? Do you have to put the new downloaded BIOS on there also?

Hmmmm, I hope I can find the new live update.
 
"please select proper boot device or insert boot media into the device"

Exact same message I had received after flashing the BIOS on my Intel board - took me three days to finally swap the new rounded cables for my old flat cables and what do ya know - the rounded went bad {not sure how flashing my bios caused the prob to present its self}.

Swapped the cables, got the Bios confirmation and away I went.

-=M=-
 
I think I may have corrupted my BIOS because I think I had 1016 and flashed to 1016. Now when I set an OC to 5:4 divider, by setting DRAM frequency to 320 and the AGP:pCi to 66.6:33.3, I get a bluescreen right when it's about to boot into windows at around 230FSB. This is weird since I was able to boot into Windows at well over 240FSB to 250 FSB before just not prime stable. The bluescreen says something about hardware drivers or BIOS may be configured improperly etc. please doube check your newly installed hardware. However, when I run everything stock everythings all fine and dandy. Don't know if I did anything stupid, but I guess i will try to flash to 1018 through DOS unless someone knows where I can get live update 5.22.02. I can't even find it on google or ASUS's ftp site. Is there a problem with that specific live update utility that would make them remove it because everything googled comes up with a dead link.
 
So does anyone know whether it matters if I detach my SATA cables from my mobo while flashing the BIOS? Espcecially the boot drive. I guess just in case the flash is for some odd reason shorting my cables. (Just a precaution since I only have one spair pair of SATA cables).
 
Does anyone know how to create a bootdisk in xp because I think the asus directions for their AFUDOS floppy setup in windows is for 98 and under. It says if you can create a bootable disk through windows then you don't need to create and autoexec.bat and config.sys files with your floppy. I have no idea on how to create those files or make my system boot into dos mode.

I just have a formatted floppy with the AFUDOS file on it and I've switched the boot order to the floppy drive, but nothing happens and it just says to remove media.

Microsoft's site says XP has no boot disk option and you can download from their site or extract part of the file from the CD or something, but I think that's to boot into windows right?

Any help would be much appreciated. Thanks.
 
there is also the EZflash method, but I'm not sure if it matters which live update or AFUDOS revision I have.

It says simply put the downloaded BIOS on a floppy.

in post push alt+f2 then insert the floppy with the BIOS.

It says EZ Flash BIOS to Refresh...hmmm, I' m not exactly sure what that means.
 
hmmm...well isn't this weird. Well I made a boot disk from bootdisk.com and flashed the bios and everythings working fine. However, I still get bluescreen messages when I push my cpu past 230 fsb. How could this be when I use to run 240-250fsb without a hitch.

The bluescreen message is about windows not working properly, check for a new BIOS, video adapter, newly installed hardware or drivers etc. or something like that.

Is that normally what you get? I thought it simply won't post or if it's unstable you get a bluescreen that says the system shut down to prevent hardware failure.

I'm not sure if it's the BIOS flash, my cpu just got lazy on me or I screwed something up.

Perhaps I have the settings incorrectly set. They are as listed;

DRAM speed: 320
AGP:pCI: 66.6:33.3
Cpu voltage: tried both auto and 1.55 (which my mobo ramps up to 1.6)
DRAM voltage: 2.75, 2.85 and auto

I tried auto, disable and enable for performance and enhanced mode

I had to reset the DRAM timings manually to 2-3-2-6 or ASUS's order 2-2-3-6, since the BIOS sets it at 2.5-4-4-8 at default.

Does this seem right to you guys.

Well the only thing I could think of is perhaps I remember there was a conflict with USB legacy support and this RAM, will try that.

And lastly does anyone know whether I should enable the spread spectrum (I'm not exactly sure what that does.)

Thanks.
 
Do not use ezflash for bios versions above 1011. the latest AFUDOS or Liveupdate must be used. Do not disconnect or connect anything while flashing, don't do anything while flashing period. If you mess up the flash the orig. bios is on the mobo cd. I have used the liveupdate quite succsessfully, and found it easy to use....good luck
legacy usb should be disables, spread spectrum should be disabled, your memory timings (2-2-3-6) @ 2.75V is correct and yes, the mobo does ramp up the cpu voltage to 1.6 even when you set it to 1.52 (mine does the same thing) The cpu actually governs its own power requirements so I don't think its anything to worry about, and 1.6 is within the safe limits for a northwood Spread spectrum is an atempt to lessen any emf interference from the mobo to the soundcard, if you have issues with poor soundcard operation you can try enabling it, but for the most part its not been reported as an issue and most people disable it as a precaution as its been known to affect the stability of an OC
 
thanks for the info twajetmech. I will see if I can get my comp back up to speed.

Now I did use Afudos to flash the BIOS because it says you need the latest Afudos and Live Update Utility to flash to 1018 however, the newest Live Update Utility 5.22.02 is nowhere to be found on the net and isn't detected by the utility itself. Anyways, just for info, if I did screw up or corrupt the BIOS I shouldn't have been able to flash the new BIOS without clearing the CMOS manually right? And if I did flash to the new BIOS then any remnant of the old BIOS should be erased correct?

Thanks.
 
darn, it wasn't the legacy support or the spread spectrum. I'm still getting blue screen when booting into windows. "Windows has shutdown to prevent damage to your system please check etc. etc." @ 235 FSB.

Now, can a processor that does 240-250FSB @ 1.6-1.7 prime stable @ 3.6 and relatively stable at around 3.7 just drop to nothing past 230FSB?

I had it overclocked for about 2 months when I bought the cpu around feb or mar of this year and left it at stock because I didn't really feel the need to overclock. Now 8 months later without stressing the cpu it's gotten weak on me? I know from others that there's not factual data supporting burning in your cpu so what happened?
 
mayakindaguy said:
Thanks for the help, but I couldn't get the system to boot so I can't get to the internet on my rig. Fortunately I fixed the problem.

However, I did read that you need Live Update version 5.22.02 which is the latest auto flash utility however, it's not listed on the ASUS site anywhere. I can download the Afudos DOS flash utility, but I am unsure about how to use the DOS flashing utility.


Version 5.28 here:

http://www.asus.com.tw/support/download/item.aspx?ModelName=Tools

gl:)
 
well I don't know if flashing to the newest BIOS is such a great idea as it has not helped me any. However, if you want to use the AFUDOS (using DOS to flash) you have to download the file from ASUS's website, with the BIOS you want. Then I formatted a floppy and went to bootdisk.com to download a file that would set up the floppy to boot into dos and autoexecute. Specifically, I dled the bios flash one. Then copied the latest afudos and BIOS onto the floppy. Reboot, changed the boot order to floppy only and then simply type this in the command prompt.

A: afudos /i <specified file name>

For the 1018 BIOS its p4ced18.rom
 
omg I had 5.28.01 this whole time. I thought that it was older than 5.22.02 because i thought the version number was the release date. When trying to find the new 1018 BIOS with the live update however, it's not listed. 1016 is the latest. However, it doesn't say that 1018 is a beta.

This whole adventure started yesterday becasue someone on the Intel thread posted that they updated to the new 1017 BIOS which I have no idea where that is, and was showing positive results because he's getting up to his old OC with less voltage. Darn performance itch. Though timid as it is it always come back a little.
 
For Dos Flash

a good solid Win 98 dos disk is good to keep handy for just this reason.

gl
 
When you use 5.28.01 you can switch servers to download the bios.
All Asus servers not synchronised ! Last time I checked, only the german one (".de") featured 1018 and even 1019.002 beta.
 
That's uber cool of you axl. Strange thing is the guy whose post started this whole adventure of mine actually flashed a 17 beta driver. wtf? What 17 beta driver? Do you flash drivers now?
I don't even know if there new BIOSs do anything good @ all.
 
Back
Top