Opty 165 is getting a mite hot...

Jayemji

Limp Gawd
Joined
Dec 7, 2006
Messages
136
I'm running Opty decently quick (have it in my sig) and it's a bit hotter than I'd like it, or at least hotter than I'd think it'd run. I have it on decent air, and SpeedFan is measuring an idle Core Temp of 38, and it hits 58 C while fully loaded.

It runs plenty stable, but I'm kinda concerned about what this will be doing to the chip come summer. I currently have VERY low ambient temps, as in one of my less-used hard drives starts out around 12 C when I boot my computer.

Am I just getting paranoid, or is this actually too hot for low ambient?
confused.gif
 
If I remember correctly the Tcase max is 65*, so you're fine. You may want to grab something more substantial though to cool (it sounds like you're running stock cooling) it for the summer like a Ninja, Infinity, AC Freezer, or even that four heatpipe AMD sink.
 
Jayemji said:
Which one? There are two kinds. :p

This one. Supposedly as good as an XP-90, and it used to sell for only ~$10-15 on ebay. I only suggested it because if you don't already have it it may be a nice ultra cheap option.
 
quadnad said:
This one. Supposedly as good as an XP-90, and it used to sell for only ~$10-15 on ebay. I only suggested it because if you don't already have it it may be a nice ultra cheap option.
Darn, I've got the one with two heatpipes on either side. :/
 
Jayemji said:
Darn, I've got the one with two heatpipes on either side. :/

well it's up to you. If you've got your computer in an air conditioned area, it won't be an issue. Otherwise some aftermarket cooling could be in the cards. that and maybe you can see if it'll do any more beyond 2.7 by cranking up the voltage!
 
quadnad said:
well it's up to you. If you've got your computer in an air conditioned area, it won't be an issue. Otherwise some aftermarket cooling could be in the cards. that and maybe you can see if it'll do any more beyond 2.7 by cranking up the voltage!
The computer room is in the room with the least insulation (read: hottest or coldest part of the house, depending on the weather). The CPU can, in fact, do 2.8 or so at least with even this motherboard and memory, but that required about 1.45 volts. I could crank it up to 3.0, but that's barely stable enough to POST. I seriously think it's the motherboard, as it would do not much over 300 fsb with another CPU. Knew I should've gotten a DFI.
 
This one. Supposedly as good as an XP-90, and it used to sell for only ~$10-15 on ebay. I only suggested it because if you don't already have it it may be a nice ultra cheap option.

I have that new heat sink on my 165, same stepping and week as the original post. But I can't do much over 2.5 GHz, even though load (dual Prime95) is around 48/54C (coretemp reading both cores). Coretemp reads higher temps than other programs too.

I thought it was my stock cooler, but after reading that review I don't think so.
 
I have that new heat sink on my 165, same stepping and week as the original post. But I can't do much over 2.5 GHz, even though load (dual Prime95) is around 48/54C (coretemp reading both cores). Coretemp reads higher temps than other programs too.

I thought it was my stock cooler, but after reading that review I don't think so.

Yeah, that heatsink isn't exactly the best out there but it's the cheapest alternative. How much voltage are you using?
 
Yeah, that heatsink isn't exactly the best out there but it's the cheapest alternative. How much voltage are you using?

Stock voltage (bios & utilities read 1.4V) gets me to 2.5 GHz.

+0.1V gets me to like 2.58 GHz. If I raise the voltage to + 0.125, weird things happen (boot drives get reordered).
 
Stock voltage (bios & utilities read 1.4V) gets me to 2.5 GHz.

+0.1V gets me to like 2.58 GHz. If I raise the voltage to + 0.125, weird things happen (boot drives get reordered).

wtf? your boot order gets messed up? Sounds a bit like a flakey motherboard.
 
SpeedFan is measuring an idle Core Temp of 38, and it hits 58 C while fully loaded.

Google CORETEMP and give that a try.... you'll see the temps reported by CORETEMP (actual temps as reported by CPU, not motherboard) will be a tad higher.

At ilde, MBM5 reports CPU temp a little higher than what CORETEMP does... but under load... I can see each core running much higher than what MBM5 reports.

Try CORETEMP and see if your individual cores are running hotter than you believe and probably exceeding the TCase Max value.

Try re-applying the heatsink and see if that helps, otherwise, get an aftermarket HSF (and make sure your cable management is organized to help your case's airflow.
 
wtf? your boot order gets messed up? Sounds a bit like a flakey motherboard.

Yeah, if I try + 0.125V, I get a "boot order has changed, press F1" message - and low and behold, my 2nd drive has been swapped it make it my boot drive.

Also, I can't flash the latest bios into my Epox, if I do, i can't boot to Windows. All previous bioses work, just not the latest.
 
Yeah, if I try + 0.125V, I get a "boot order has changed, press F1" message - and low and behold, my 2nd drive has been swapped it make it my boot drive.

Also, I can't flash the latest bios into my Epox, if I do, i can't boot to Windows. All previous bioses work, just not the latest.

That is really odd. Short of getting another motherboard there really isn't a good way to see if your proc will go any higher...
 
Try CORETEMP and see if your individual cores are running hotter than you believe and probably exceeding the TCase Max value.

Try re-applying the heatsink and see if that helps, otherwise, get an aftermarket HSF (and make sure your cable management is organized to help your case's airflow.
Here's the odd part:

It's been running like this for weeks without a single hiccup...
 
Thats what I've been saying though: it isn't running out of spec.
I know, as soon as I'm finished mirroring my hard drive, I'll install coretemp and see if it gives me a different reading. I'm doubting it will, though, as speedfan reads a significantly hotter temperature (5-8C) than my last temperature monitoring program, Coretemp. (Though that may be because coretemp is a POS program. Case in point
 
I know, as soon as I'm finished mirroring my hard drive, I'll install coretemp and see if it gives me a different reading. I'm doubting it will, though, as speedfan reads a significantly hotter temperature (5-8C) than my last temperature monitoring program, Coretemp.

Are you running the stock cooler?
 
ahhh. i must have missed that. I'm not really familiar with that HSF, so I don't really know how it stacks up to the competition.

When installing the HSF, I'm assuming you did the good ole tiny dot of AS5 method?

EDIT: actually I just checked out a review and if you're running it at half speed that is most definitely the reason. according to this, the Venus is very responsive to the amount of airflow.
 
That is completely normal, and relates to how they interface with the integrated heatsink.
 
That is completely normal, and relates to how they interface with the integrated heatsink.
So, do I go by average of the two, the hottest core, or what? :confused:

This certainly explains why CPU1 seems to be less stable...
 
So, do I go by average of the two, the hottest core, or what? :confused:

This certainly explains why CPU1 seems to be less stable...

It doesn't really matter what you 'go by,' you just want to make sure that both of them are under the TCase Max of 65C.
 
Back
Top