OCing Core i7 950

maverick786us

2[H]4U
2FA
Joined
Aug 24, 2006
Messages
2,427
Now that the price of Core i7 950 have declined. I m considering it to be a very good CPU for gaming. How is the combination of Intel Core i7 950 + Gigabyte X58A-UD5 GRAB, if I want to OC it to 4.2GHz and above? Offcourse I will be using TRUE 120 heat sink. Although there are numerous reviews of Corsair H70 heat sink so I don't know which one of these 2 is better.
 
Between those two, If you go that high, I think you should go with H70.
 
And how good is the mobo as far as OCing is concerned? Or should I go for an ASUS counterpart?
 
I don't have that board myself, but I heard that it is an awesome mobo for OCing.
 
If anything, the i7-950 at any given overclocked clock speed will benckmark a tad slower than an i7-920 or i7-930 at the same clock speed (assuming that the maximum multiplier is always selected) due to the lower BCLK needed for the 950 to reach the same clock speed. Plus, you will need better cooling if you want that i7-950 to overclock to the same degree as the i7-930 (the "same degree" meaning the same BCLK speed and factory-default maximum multiplier settings).
 
Other than TRUE 120 and Corsair H70 which are the best air cooling devices what else can you suggest?
 
If anything, the i7-950 at any given overclocked clock speed will benckmark a tad slower than an i7-920 or i7-930 at the same clock speed (assuming that the maximum multiplier is always selected) due to the lower BCLK needed for the 950 to reach the same clock speed. Plus, you will need better cooling if you want that i7-950 to overclock to the same degree as the i7-930 (the "same degree" meaning the same BCLK speed and factory-default maximum multiplier settings).


Can you show me some comparision chart with benchmark comparision between 920-30 and 950?
 
Can you show me some comparision chart with benchmark comparision between 920-30 and 950?

Hmmm...

Unfortunately, I was unable to reproduce my earlier findings. I could not get a consistent enough result at either of the speeds which the lower-end i7 CPUs typically are overclocked to. This means that at each tested clock speed, the results vary by enough of a margin in either direction that I can call this a statistical tie.

By the way, my older i7-920 did perform slightly faster at 3.675GHz than my i7-950 does at 3.72GHz. But that CPU did not run stably enough at 3.675GHz to continue running at that level of an overclock for long.
 
920 is discontinued. Do you think there is any possibility that Intel might release an E0 Stepping version of 950 that may perform equal as 920 clock by clock or slightly better?
 
There is no clock-for-clock performance difference between the Quad-core X58 i7 CPUs. An i7 950 simply allows for the usage of a higher multiplier if you choose to use it.

By now, almost all the popular motherboards overclock well (Gigabyte UD3 and UD5, Asus, eVGA, MSI, Biostar... and even though DFI never released updated boards, those were overclocking monsters).

http://www.microcenter.com/specials...s Friday BYOPC 20101015&utm_source=ACT_BYO_1& - This is a pretty good combo deal for the i7 950 + Asus mobo (but Microcenter In-store only, I believe).

The BIGGEST factor in achieving a high overclock is the CPU itself. You can try to hand-pick a known good batch, but that's difficult to do with newer CPUs due to lack of data, and seemingly a lack of good batches. There don't seem to be any Golden batch CPUs like there were when the D0 revision was first introduced.

Tip: If you pick up an i7 950, there's a chance you can grab a "C" batch. I picked one from Microcenter ( 3007C146 ), and it's pretty good already on stock cooling. A pesky injury has prevented me from trying better cooling... but this CPU will do 4Ghz at below stock volts (eVGA e758 board). It seems that most of the "C" batch CPUs have been better than average, so I chose this over 2 different "A" batches (while holding my 15-page printout of all the OC-Batch data I could find).

As far as cooling: The original TRUE is still good if you already own it and a compatible mounting mechanism, otherwise:

Top tier HUGE dual tower heatsinks: Thermalright Silver Arrow, Noctua NH-D14, Cogage Arrow. - I'd go for the Silver Arrow, which is a Cogage Arrow, but with Thermalright's new fans, which are better than the Noctua fans. In most reviews, this setup outperforms the NH-D14 slightly. Directron and CrazyPC have it for $75.

Single-Tower heatsinks: Prolimatech Megahalems and Thermalright Venomous-X. They are about equal. The Ven-X is essentially Thermalright's updated TRUE. The Mega is a bit heavier, and features what I'd call a single split-tower.

Corsair H70: It seems to perform somewhat well, but it requires some loud fans to do so. I'd prefer any of the above heatsinks because I know they can perform well at low noise levels.

RAM: I'm using 6GB of G.skill's ECO DDR3 1600 1.35v series (7-8-7-24). I bought (2) 4GB kits, so I'll need to sell or use the extra stick of RAM. Mushkin has an equivalent and similarly affordable RAM series. Kingston's LoVo series is more expensive, but their 1866 version is a little better.

Mushkin/Newegg had a crazy sale on their 6GB Redline 6-8-6, 1600, 1.65v RAM. I would have purchased that if I didn't already have the ECO.

That about wraps it up.
 
Last edited:
There is no clock-for-clock performance difference between the Quad-core X58 i7 CPUs. An i7 950 simply allows for the usage of a higher multiplier if you choose to use it.

By now, almost all the popular motherboards overclock well (Gigabyte UD3 and UD5, Asus, eVGA, MSI, Biostar... and even though DFI never released updated boards, those were overclocking monsters).

http://www.microcenter.com/specials...s Friday BYOPC 20101015&utm_source=ACT_BYO_1& - This is a pretty good combo deal for the i7 950 + Asus mobo (but Microcenter In-store only, I believe).

The BIGGEST factor in achieving a high overclock is the CPU itself. You can try to hand-pick a known good batch, but that's difficult to do with newer CPUs due to lack of data, and seemingly a lack of good batches. There don't seem to be any Golden batch CPUs like there were when the D0 revision was first introduced.

Tip: If you pick up an i7 950, there's a chance you can grab a "C" batch. I picked one from Microcenter ( 3007C146 ), and it's pretty good already on stock cooling. A pesky injury has prevented me from trying better cooling... but this CPU will do 4Ghz at below stock volts (eVGA e758 board). It seems that most of the "C" batch CPUs have been better than average, so I chose this over 2 different "A" batches (while holding my 15-page printout of all the OC-Batch data I could find).

As far as cooling: The original TRUE is still good if you already own it and a compatible mounting mechanism, otherwise:

Top tier HUGE dual tower heatsinks: Thermalright Silver Arrow, Noctua NH-D14, Cogage Arrow. - I'd go for the Silver Arrow, which is a Cogage Arrow, but with Thermalright's new fans, which are better than the Noctua fans. In most reviews, this setup outperforms the NH-D14 slightly. Directron and CrazyPC have it for $75.

Single-Tower heatsinks: Prolimatech Megahalems and Thermalright Venomous-X. They are about equal. The Ven-X is essentially Thermalright's updated TRUE. The Mega is a bit heavier, and features what I'd call a single split-tower.

Corsair H70: It seems to perform somewhat well, but it requires some loud fans to do so. I'd prefer any of the above heatsinks because I know they can perform well at low noise levels.

RAM: I'm using 6GB of G.skill's ECO DDR3 1600 1.35v series (7-8-7-24). I bought (2) 4GB kits, so I'll need to sell or use the extra stick of RAM. Mushkin has an equivalent and similarly affordable RAM series. Kingston's LoVo series is more expensive, but their 1866 version is a little better.

Mushkin/Newegg had a crazy sale on their 6GB Redline 6-8-6, 1600, 1.65v RAM. I would have purchased that if I didn't already have the ECO.

That about wraps it up.


4GHz at stock voltage is very good, with littlebit tweak I won't be hard to reach 4.1-4.2GHz. What is the temprature at that speed?
 
I love this thread; it's pretty much what I'm getting soon, with the 950 and all.
 
And how good is the mobo as far as OCing is concerned? Or should I go for an ASUS counterpart?

i have a x85a-ud3 rev 1.0 abd its a great OCing board.but its no better than my three other x58a-ud3r's at OCing.heres my UD5 at 230 bclk
2dlj0gl.jpg


it also runs my 920 at 21x214@4502 very solid.
t0t5yu.jpg

2lsbfaw.jpg
 
i have a x85a-ud3 rev 1.0 abd its a great OCing board.but its no better than my three other x58a-ud3r's at OCing.heres my UD5 at 230 bclk
2dlj0gl.jpg


it also runs my 920 at 21x214@4502 very solid.
t0t5yu.jpg

2lsbfaw.jpg

at 1.34V you are able to hit almost close to 4Ghz? :eek:
 
Going for a 4Ghz on the 950 when I get mine, something comfortable.

Do you guys disable turbo mode for that? I've seen mixed views on it.
 
Back
Top