OC Settings

C

captain204mike

Weaksauce
Joined
Nov 20, 2006
Messages
125
here is my OC settings can someone help me out to go farther,, my memory needs to be faster i think

right now FSB setting is 250
HTT Multi-lowest multiplier
cpu is 10x
memory is set at lowest setting
cpu z shows--- core speed 2477
multiplier x10
Bus Speed 247.8
HT Link 247.8

the memory shows
Dual Channel
Frequency is 123.9
FSB:Dram--CPU/20
Cas# Latency-- 2.5
Ras# to Cas#--2
Ras Precharge-2
Cycle Time--5
Bank Cycle Time--7
Command Rate---2T
DRAM Idle Timer--256

Does something look wrong with this,, do i need to change some stuff to get up to full speed?

by the way how do i upload a pic?
 
Start raising your fsb from 250. Looks like you have a divider on your ram so that's good. Your HTT link needs to be raised to 3x. You could try pushing it to 1T.
 
You could try pushing it to 1T---what do you mean by this?
also will that speed my memory up,,
i did change my HTT multi to 3x
my memory in the bios is set to its lowest setting with all the other setting of the memory at the defualt values of AUTO
and as far as 1T as mentioned before, what is that called in the bios
 
captain204mike said:
You could try pushing it to 1T---what do you mean by this?
also will that speed my memory up,,
i did change my HTT multi to 3x
my memory in the bios is set to its lowest setting with all the other setting of the memory at the defualt values of AUTO
and as far as 1T as mentioned before, what is that called in the bios
Click to expand...

He means set the Command Rate to 1T instead of 2T.

I don't really recommend this as it's sorta useless...

Either way, your RAM is running REALLY slow right now... Since your CPU is set to about 2500mhz, your RAM is running at just under 125mhz (or 250mhz DDR). How did I get this value? Well, it says FSB: Dram ratio = CPU/20... That means your RAM is running at your CPU speed / 20.

Your RAM is rated for 200mhz or 400mhz DDR. Where it says FSB: Dram = CPU/20... Try to get that closer to CPU/15 or so, or pump the FSB up closer to 300.

So, if you set your FSB to 260 it's not stable? There's really nothing holding you back...

Your core might need more voltage.
 
should i leave my HTT multi to 3x
and cpu to 10x
then up my FSB too 275

but i cant change anything from the lowest setting in the memory DRAM Frequency Set to anything higher or the pc wont start and i have to reset cmos
maybe my memory is CRAP??
i have Kingston 4--- 1gb sticks
should i take some memory out would that help me any to get faster memory speeds?

i think just the memory stuff have me confused,,starting to understand the other a little bit
 
ok just tried to up the FSB to 265, changed the memory setting to next from lowest setting
wouldnt start,, had to reset cmos and load defualts
now im running default memory speeds and everything and CPU-Z shows my memory at
166mhz
cpu/12
2.5-3-3-7
command rate 2T
is that normal for stock?
 
ok now i am at
240 FSB
4x HT multi
10x Cpu Multi
and 150= Ram/FSB:03/04

cpu-z shows 2408 clock speed
10x multiplier
240 bus speed
961 HT Link

memory shows Dual Channel
171mhz
CPU/14
2.5-3-3-7
i took 2 of the 1GB sticks out so now im only at 2GB but it did start up after taking the 2 out using the 150 memory setting.
so am i better off running 2 gigs instead of 4, can i put 1 more in it will that help?
also what do i need to do now to get processor up more?
should i change multipliers around?, up memory speed to something else
i dont know how to figure the ratios
 
You must log in or register to reply here.
Back
Top