JakFrost
Limp Gawd
- Joined
- Dec 2, 2005
- Messages
- 241
Cross-post: NVIDIA Forums > nZone > Hardware > nForce Mobos > nVidia nForce MediaShield 15.23, .25, .26 - Does Not Install!, MediaShield installer does not install services, GUI, or files.
The Problem
I have the an nVidia nForce 4 AMD SLI based motherboard and I have been using the nForce 6.86 storage drivers for a very long time. Before this problem I had my system with 2 x 320GB nVidia RAID MIRROR for OS C: and D: drives, and 2 x 500GB nVidia RAID MIRROR for E: drive. All four SATA ports on my motherboard were set to RAID and MediaShield 6.86 worked fine showing all the drives.
Intel SSD + nVidia MediaShield 6.86 = OS Start Freeze!
I have just purchased the Intel X25-M 80GB MLC SSD drive and decided to re-install Windows XP SP3 cleanly on this drive. This is because I need to do a partition alignment and the only way to do it at this time is to pre-create the partition with "diskpar.exe" utility from Microsoft and set the sector offset to 2048 sectors (512-bytes per sector) or 1 MB into the disk to ensure that the new partition starts at a 4KB SSD page boundary and also at a 1MB boundary that will be evenly divided by various SSD erase blocks (128KB, 256KB, 512MB) and RAID stripe sizes (64KB, 128KB, 256KB) so they will all fall on the that 1MB boundary. I read that Windows Vista and 7 do their partition creation on sector 2048 so I'm following suit with this Windows XP install also on this SSD.
I first tried to test the SSD by doing a clone copy of my OS from the HDD using Acronis Disk Manager v10 but the SSD won't boot the OS all the way. I did a clean OS installation on a the new SSD and then installed the old MediaShield 6.86 storage driver but it still will not boot up and gets stuck loading a driver after MUP.sys according to Safe Mode, same as with the image.
New OS Install + nVidia nForce 15.23, .25, .26 Drivers = No MediaShield GUI!
Now I'm trying to do new OS install on the SSD without RAID for C: drive connected to SATA Port 4 - RAID = Disabled. Also I have 2 x 500GB set in a nVidia RAID MIRROR for D: drive SATA Ports 1, 2 - RAID = Enabled for storage and another 1 x 500 GB E: drive on SATA Port 3 - RAID = Disabled.
After the problems with 6.86 I noticed that a new nForce 15.23 release because available for my motherboard and downloaded this one. However, when I install it in my OS the MediaShield GUI does not get created and the NvRaidService*.dll files do not get copied to "%SystemRoot%\system32\" folder. I downloaded the newer 15.25 and 15.26 releases and they do not install MediaShield either, even though all the other drivers install, including the newer storage drivers 10.3.0.46.
I've tried changing my BIOS to make all SATA ports as RAID = Enabled but still could not get MediaShield to install. I tried adding the SSD to a new Stripped array by itself and installing the OS on it but MediaShield won't install. I changed the drive from SATA Port 1 and Port 4 but it doesn't matter. MediaShield won't install.
nVidia nForce 15.23, .25, .26 Drivers - \IDE\WinXP\raidtool = raidtool.cab + Missing Installation INF!!!
I extracted the installation package and looked into the "\IDE\WinXP\raidtool" folder where MediaShield is supposed to be and I only find a compressed "raidtool.cab". When I extract that I find all the required files "NvRaidServer*.dll nvraidservice.exe NvRaidSv*.dll NvRaidWizard*.dll NvSataConnection.exe NvSataConnection*.dll nvsto*.chm" including the "RegRaidSedona.bat" utility but this CAB file does not get installed. It contains the "default.inf" file but this file does not install properly from this cab. It contains the "DestDir=11" = "Copy To %SystemRoot%\system32" folder instructions for certain files but they don't get implemented since this .inf is never called.
The "RegRaidSedona.bat" is more interesting since it assumes that the "default.inf" was called and it copies the *.dll files to the proper folders and tries to register the "nvraid*.dll" files and then start MediaShield "nvraidservice.exe" but it doesn't work fully. When I try to manually copy the files and run this batch file I get a partial result. The new NVIDIA Control gets the "(+) Storage" group with three pages of information but all the pages have blank tables in them and do not display any drives in the system. My guess is because "nvraidservice.exe" is failing to do what it is supposed to do.
Also there is no more "NvRaidMan.exe" GUI file in the "raidtool.cab" even though the new "nvraidservice.exe" still references it internally.
What To Do Next?!
I had problems previously with the old 6.86 version the same way trying to get it installed with the GUI and I finally did it but that was years ago and I don't remember what magic I did to make it work. Now it's the new 15.xx releases and the same problem is here with a new drive and new OS install. I cannot use the old 6.86 drivers since they freeze my OS with this SSD. What do I do next?
Either way, if it's something that I'm doing or not I should be able to force the MediaShield GUI to install properly whether I'm using RAID or not because there's always a chance that I'll switch to RAID for other drives in the system later.
[size=-2]
CPU: AMD Opteron 175 Dual-Core 2.2 GHz 1 MB 90 nm 939 11x CCBWE 0543TPMW VID 1.350 V - 2,475 MHz (225x11x4), 1.55 V (1.55 V x 104.8 %)
FAN: Zalman CNPS9500 LED 92 mm Fan+Heatsink + Arctic Silver 5 Thermal Paste 99.9 % - 35 C Idle, 45 C Load
MOB: DFI LanParty UT SLI-DR Expert 939 nF4 PCI-e Rev.AA0 - BIOS: 2006-04-06 Modded, LDT 1.20 V, Chipset 1.52 V, 42 C Load
RAM: Mushkin 1 GB XP4000 Redline 991493 DDR500 3-3-2-8 2.6-2.9 V CE-6 - (4) DIMMs, 225 MHz (1:1) 2T 3-3-2-8, 2.80 V
VID: eVGA nVidia GTX 260 896 MB G92 192c 576/999 MHz PCI-e 2.0 16x 2xDVI 1xSVid 1xHDTV - 600/1100 MHz, DVI to LCD, HDMI 60' to 50" Plasma TV.
SAT: Silicon Image 3114 PCI SATA-I 150 MB/s RAID 0,1,5 Onboard Controller FW: 5.3.14 Modded, Only for eSATA since PCI bus problems with Sound Blaster X-Fi
HDD: Western Digital Caviar SE16 500 GB WD5000AAKS 16 MB SATA-II - (2) in (2) 465 GB nVidia RAID1 (Mirror) Arrays
HDD: Western Digital Caviar GP Green 1 TB WD10EACS 16 MB SATA-II - (2) external Movies, (2) external for Backups
ENC: MacAlly G-S350SU External HDD Enclosure 3.5" eSATA USB 2.0 Aluminum, Universal 12V Adapter - (2) external WD GP 1TB for Movies
ENC: i-Rocks 9410 External HDD Enclosure 3.5" eSATA USB 2.0 Aluminum, Univeral 12V Adapter - (2) external WD GP 1TB for Backups
NIC: nVidia nForce4 Gigabit Onboard PCI NIC
NIC: Marvell Yukon 88E8001 Gigabit Onboard PCI NIC
SOU: Creative Labs Sound Blaster X-Fi Xtreme Music 24-bit 128-Voice 109dB SNR - EAX 4.0 for games and music.
SOU: RealTek ALC850 AC'97 Rev 2.3 8-Channel Onboard Audio - S/PDIF out to vid card for HDMI Audio for TV.
BLU: LG GGW-H20L Blu-ray 6x BD-RE 16x DVD SL/DL 48x CDR SATA - FW: YL05
DVD: NEC ND-3550A 16x DVD+-RW SL/DL 48X CDR PATA - FW: 1.07
POW: OCZ PowerStream 520W SLI ADJ ATX2.0 EPS12, +3.3V 28A +5V 40A +12V 33A
CAS: Lian-Li PC-V1200 Plus Mid-ATX Aluminum 4x5.25 6x3.5 2x120mm - Best case to date in my opinion.
MON: HP LP2475w 24-inch LCD H-IPS Monitor Wide Gamut 102% NTSC 6-12ms Response - 1920x1200x32 60Hz, DVI, GIG122/GIG052, Bri 15, Con 80, 9300K
ROU: Linksys BEFSR81 EtherFast Cable/DSL Router 8-port Switch 100MBps FW: 2.51.3
JOY: CH Products Fighterstick USB 3 axes 24 buttons
THR: CH Products Pro Throttle USB 3 axes 24 buttons
PED: CH Products Pro Pedals USB 3 axes
KBD: Microsoft Natural Keyboard Pro USB/PS2 Media Keys
MOU: Microsoft IntelliMouse Explorer 1.0 Optical USB/PS2 Scroll-Wheel 5-Button
[/size]
The Problem
I have the an nVidia nForce 4 AMD SLI based motherboard and I have been using the nForce 6.86 storage drivers for a very long time. Before this problem I had my system with 2 x 320GB nVidia RAID MIRROR for OS C: and D: drives, and 2 x 500GB nVidia RAID MIRROR for E: drive. All four SATA ports on my motherboard were set to RAID and MediaShield 6.86 worked fine showing all the drives.
Intel SSD + nVidia MediaShield 6.86 = OS Start Freeze!
I have just purchased the Intel X25-M 80GB MLC SSD drive and decided to re-install Windows XP SP3 cleanly on this drive. This is because I need to do a partition alignment and the only way to do it at this time is to pre-create the partition with "diskpar.exe" utility from Microsoft and set the sector offset to 2048 sectors (512-bytes per sector) or 1 MB into the disk to ensure that the new partition starts at a 4KB SSD page boundary and also at a 1MB boundary that will be evenly divided by various SSD erase blocks (128KB, 256KB, 512MB) and RAID stripe sizes (64KB, 128KB, 256KB) so they will all fall on the that 1MB boundary. I read that Windows Vista and 7 do their partition creation on sector 2048 so I'm following suit with this Windows XP install also on this SSD.
I first tried to test the SSD by doing a clone copy of my OS from the HDD using Acronis Disk Manager v10 but the SSD won't boot the OS all the way. I did a clean OS installation on a the new SSD and then installed the old MediaShield 6.86 storage driver but it still will not boot up and gets stuck loading a driver after MUP.sys according to Safe Mode, same as with the image.
New OS Install + nVidia nForce 15.23, .25, .26 Drivers = No MediaShield GUI!
Now I'm trying to do new OS install on the SSD without RAID for C: drive connected to SATA Port 4 - RAID = Disabled. Also I have 2 x 500GB set in a nVidia RAID MIRROR for D: drive SATA Ports 1, 2 - RAID = Enabled for storage and another 1 x 500 GB E: drive on SATA Port 3 - RAID = Disabled.
After the problems with 6.86 I noticed that a new nForce 15.23 release because available for my motherboard and downloaded this one. However, when I install it in my OS the MediaShield GUI does not get created and the NvRaidService*.dll files do not get copied to "%SystemRoot%\system32\" folder. I downloaded the newer 15.25 and 15.26 releases and they do not install MediaShield either, even though all the other drivers install, including the newer storage drivers 10.3.0.46.
I've tried changing my BIOS to make all SATA ports as RAID = Enabled but still could not get MediaShield to install. I tried adding the SSD to a new Stripped array by itself and installing the OS on it but MediaShield won't install. I changed the drive from SATA Port 1 and Port 4 but it doesn't matter. MediaShield won't install.
nVidia nForce 15.23, .25, .26 Drivers - \IDE\WinXP\raidtool = raidtool.cab + Missing Installation INF!!!
I extracted the installation package and looked into the "\IDE\WinXP\raidtool" folder where MediaShield is supposed to be and I only find a compressed "raidtool.cab". When I extract that I find all the required files "NvRaidServer*.dll nvraidservice.exe NvRaidSv*.dll NvRaidWizard*.dll NvSataConnection.exe NvSataConnection*.dll nvsto*.chm" including the "RegRaidSedona.bat" utility but this CAB file does not get installed. It contains the "default.inf" file but this file does not install properly from this cab. It contains the "DestDir=11" = "Copy To %SystemRoot%\system32" folder instructions for certain files but they don't get implemented since this .inf is never called.
The "RegRaidSedona.bat" is more interesting since it assumes that the "default.inf" was called and it copies the *.dll files to the proper folders and tries to register the "nvraid*.dll" files and then start MediaShield "nvraidservice.exe" but it doesn't work fully. When I try to manually copy the files and run this batch file I get a partial result. The new NVIDIA Control gets the "(+) Storage" group with three pages of information but all the pages have blank tables in them and do not display any drives in the system. My guess is because "nvraidservice.exe" is failing to do what it is supposed to do.
Also there is no more "NvRaidMan.exe" GUI file in the "raidtool.cab" even though the new "nvraidservice.exe" still references it internally.
What To Do Next?!
I had problems previously with the old 6.86 version the same way trying to get it installed with the GUI and I finally did it but that was years ago and I don't remember what magic I did to make it work. Now it's the new 15.xx releases and the same problem is here with a new drive and new OS install. I cannot use the old 6.86 drivers since they freeze my OS with this SSD. What do I do next?
Either way, if it's something that I'm doing or not I should be able to force the MediaShield GUI to install properly whether I'm using RAID or not because there's always a chance that I'll switch to RAID for other drives in the system later.
[size=-2]
CPU: AMD Opteron 175 Dual-Core 2.2 GHz 1 MB 90 nm 939 11x CCBWE 0543TPMW VID 1.350 V - 2,475 MHz (225x11x4), 1.55 V (1.55 V x 104.8 %)
FAN: Zalman CNPS9500 LED 92 mm Fan+Heatsink + Arctic Silver 5 Thermal Paste 99.9 % - 35 C Idle, 45 C Load
MOB: DFI LanParty UT SLI-DR Expert 939 nF4 PCI-e Rev.AA0 - BIOS: 2006-04-06 Modded, LDT 1.20 V, Chipset 1.52 V, 42 C Load
RAM: Mushkin 1 GB XP4000 Redline 991493 DDR500 3-3-2-8 2.6-2.9 V CE-6 - (4) DIMMs, 225 MHz (1:1) 2T 3-3-2-8, 2.80 V
VID: eVGA nVidia GTX 260 896 MB G92 192c 576/999 MHz PCI-e 2.0 16x 2xDVI 1xSVid 1xHDTV - 600/1100 MHz, DVI to LCD, HDMI 60' to 50" Plasma TV.
SAT: Silicon Image 3114 PCI SATA-I 150 MB/s RAID 0,1,5 Onboard Controller FW: 5.3.14 Modded, Only for eSATA since PCI bus problems with Sound Blaster X-Fi
HDD: Western Digital Caviar SE16 500 GB WD5000AAKS 16 MB SATA-II - (2) in (2) 465 GB nVidia RAID1 (Mirror) Arrays
HDD: Western Digital Caviar GP Green 1 TB WD10EACS 16 MB SATA-II - (2) external Movies, (2) external for Backups
ENC: MacAlly G-S350SU External HDD Enclosure 3.5" eSATA USB 2.0 Aluminum, Universal 12V Adapter - (2) external WD GP 1TB for Movies
ENC: i-Rocks 9410 External HDD Enclosure 3.5" eSATA USB 2.0 Aluminum, Univeral 12V Adapter - (2) external WD GP 1TB for Backups
NIC: nVidia nForce4 Gigabit Onboard PCI NIC
NIC: Marvell Yukon 88E8001 Gigabit Onboard PCI NIC
SOU: Creative Labs Sound Blaster X-Fi Xtreme Music 24-bit 128-Voice 109dB SNR - EAX 4.0 for games and music.
SOU: RealTek ALC850 AC'97 Rev 2.3 8-Channel Onboard Audio - S/PDIF out to vid card for HDMI Audio for TV.
BLU: LG GGW-H20L Blu-ray 6x BD-RE 16x DVD SL/DL 48x CDR SATA - FW: YL05
DVD: NEC ND-3550A 16x DVD+-RW SL/DL 48X CDR PATA - FW: 1.07
POW: OCZ PowerStream 520W SLI ADJ ATX2.0 EPS12, +3.3V 28A +5V 40A +12V 33A
CAS: Lian-Li PC-V1200 Plus Mid-ATX Aluminum 4x5.25 6x3.5 2x120mm - Best case to date in my opinion.
MON: HP LP2475w 24-inch LCD H-IPS Monitor Wide Gamut 102% NTSC 6-12ms Response - 1920x1200x32 60Hz, DVI, GIG122/GIG052, Bri 15, Con 80, 9300K
ROU: Linksys BEFSR81 EtherFast Cable/DSL Router 8-port Switch 100MBps FW: 2.51.3
JOY: CH Products Fighterstick USB 3 axes 24 buttons
THR: CH Products Pro Throttle USB 3 axes 24 buttons
PED: CH Products Pro Pedals USB 3 axes
KBD: Microsoft Natural Keyboard Pro USB/PS2 Media Keys
MOU: Microsoft IntelliMouse Explorer 1.0 Optical USB/PS2 Scroll-Wheel 5-Button
[/size]
Last edited:
As an Amazon Associate, HardForum may earn from qualifying purchases.