Noob with E6600, 680i looking for advice

xtro

n00b
Joined
Jan 20, 2007
Messages
4
Hi,

I have just tried my first OC and would like some advice and comments on my end results.
I was able to reach 11754 in 3D mark 06 and was wondering if this was a desent score for the system I have.

After reading may posts I ended up at 1.60v to maintain a stable 1660 FSB/830 mem configuration for a 3700 plus MHz. Anything below that in volts and I need to reduce the FSB/mem too. I used the 680i guide as my starting point.

I am running the orthos small FFTs-CPU stress test as we speak and max temp so far is 61c with around 43c at idle.

It seems 3700 MHz is a good number, but I'm not sure how that compares to my score in 3D mark 06. My sig has my basic system configuration.

3D Mark 06 11754
SM 2.0 5113
SM 3.0 5159
CPU 3178

BTW I had all my normal programs installed including virus protection when I did this test.

Thanks ahead of time for any replies.
 
Looks good to me.

I needed my CPU @ 4ghz and the 8800GTX @ 658 / 1952 to get around 12500.

Get the ATI tool or RivaTuner and start pushing that VGA!
 
"CORE 2 DUO E6600 @ 3.8GHZ 1.4675V (1.42 In Windows)"

In your sig you have only 1.46v. How do you pull 3.8 with such a low voltage? Do you think I should back off to like 1.45 and start the increase with my FSB all over? I had started at 1.5v and was only able to hit 3.5GHz before windows would not load. I pushed up to 1.6v since my temps were running low and I was then able to hit 3.7 stable.

I have since pushed my 8800 GTX an extra 52 from the 576 to 628 without any real temp changes. Should I adjust the memory too for it is running still 900? In your sig you have 658 I'll try that.
 
What are you using for Cpu cooling? Your processor at 1.6v is cooler than mine at 1.5v.

Also did you o/c your video card to obtain that 3d mark score? or is it stock?
 
"CORE 2 DUO E6600 @ 3.8GHZ 1.4675V (1.42 In Windows)"

In your sig you have only 1.46v. How do you pull 3.8 with such a low voltage? Do you think I should back off to like 1.45 and start the increase with my FSB all over? I had started at 1.5v and was only able to hit 3.5GHz before windows would not load. I pushed up to 1.6v since my temps were running low and I was then able to hit 3.7 stable.

I have since pushed my 8800 GTX an extra 52 from the 576 to 628 without any real temp changes. Should I adjust the memory too for it is running still 900? In your sig you have 658 I'll try that.


All Video Cards or CPUs are different. If you use the ATI tool, it has an option to find your maximum Core and Memory overclocks.

Mine overclocks quite high on the Core, but the memory performance is very poor @ 1952
(8800GTX)

My brother has an 8800GTS and it overclocks to 660 on the core and 2000 on the memory. Sick!

Also, make sure that you set the VGA's fan to run @ 75 to 100% when overclocking. You can do this through RivaTuner or through the Ntune software provided by Nvidia.

@ 3.8ghz I need 1.475 In bios (1.42 In windows) for 3Dmark06, 3Dmark05 and general gaming, encoding, browsing... But not orthos stable and I really don't care:p

@ 4ghz I need 1.52V In bios.
 
All Video Cards or CPUs are different. If you use the ATI tool, it has an option to find your maximum Core and Memory overclocks.

Mine overclocks quite high on the Core, but the memory performance is very poor @ 1952
(8800GTX)

My brother has an 8800GTS and it overclocks to 660 on the core and 2000 on the memory. Sick!

Also, make sure that you set the VGA's fan to run @ 75 to 100% when overclocking. You can do this through RivaTuner or through the Ntune software provided by Nvidia.

@ 3.8ghz I need 1.475 In bios (1.42 In windows) for 3Dmark06, 3Dmark05 and general gaming, encoding, browsing... But not orthos stable and I really don't care:p

@ 4ghz I need 1.52V In bios.

Those are nice OC numbers. I'll try the 8800 OC with Riva Tuner
 
What are you using for Cpu cooling? Your processor at 1.6v is cooler than mine at 1.5v.

Also did you o/c your video card to obtain that 3d mark score? or is it stock?

I am using a Danger Den water block through a Danger Den radiator with two 120 fans on on it with a 5 /14 drive bay reservoir and a good 12v pump all connected with 1/2 inch tubing. My CPU temp in bios first time I started up not OCed was 19c.

I did OC the card from 576 to 628 to see the temps and there was no changes for the card runs at 67c normally and 50c with the fan locked at 100%. With it in auto the increase might have increased the fan but the temp never moved from 67c.
 
Back
Top