NF7S-2 random reboot

BackStabber

Limp Gawd
Joined
Sep 22, 2002
Messages
357
I have NF7s-2, 550watt power, 9700PRO, 1 gig kingston 3200 in dual channel, 37 gig raptor and 120 gig maxtor ata 133, in games every thing works fine counter strike may run 2 hrs or 20 minutes then reboots. some other games crash back to desktop, DR Watson shows no errors. Any Ideas O cpu xp3000 400 fsb model

Temp on the cpu is 43 C Full load

no over clock at this time
 
Please list everything you've tried so far to fix it before we go over the 300 possible reasons why this may be happening. If you haven't tried anything yet then get to it! (new mobo/video drivers, bios setting changes etc etc all the obvious stuff you should have tried already ;) )

btw, what psu are you using?
 
Can't remember what that error code means but have you swapped a psu to test yet? Reading newegg user reviews reveals quite a few people who complained about that psu...not many but just enough to suspect it as the culprit. I don't recommend that you dish out $80 for a new one just yet, try swapping first if you can.
 
what are your voltages at. I know that the original nf7-s boards undervolted the Vcore and overvolted the vdimm..

I have to have my vcore set to 1.725, so that my Vcore doesn't drop below 1.66 at load.. And I have a PCP&C 510 Deluxe... ;)
 
sandra had my voltage at 1.63 I raised now 1.65 and 1.63 at load should I raise it further
I can run the sandra cpu tests for 30 minutes no problems can also run 3Dmark 2001se no problem
 
I'd probably crank it up another notch, so you're atleast giving the cpu it's default voltage under load. Also, what are your other voltages looking light? How's your heat in the case? Also, what drivers are you running?
 
ok now under load on sandra after 12 runs of the cpu math and multi media it never goes below 1.65 all the other votages are good running 37 gig raptor

how much votage drop on cpu can you have before gaming problems show up

Mb temp 29 under load
CPU hotter now 47 under load If I turn up all the fans It goes to 44.5 ill test it out tomorrow didnt think cpu voltage 1.63 would cause that much trouble

have the board in bios set 1.7 sandra reads 1.66 at idle and 1.65/1.66 under full load
 
It depends on the CPU, as to how much lower you can go.. But, it's good to have it at atleast the default voltage, so you can eliminate it as a potential issue while you're troubleshooting
 
it's a possibility.. which version are you running.. On my rig, I don't even bother with the nVidia drivers, I don't even use the ITB drivers from the earlier UDP's..

Just use the standard MS drivers.. You're not going to see hardly any performance differences, and if you do, they'll be pretty small...


On my rig, I'm using the 4.24 UDP's, withouth the IDE driver. I use the standard MS driver for IDE, and I use the 1.0.0.50 SATA RAID driver for the silicon image controller.

Runs like a champ..
 
Thanks for the info

since I upped the voltage have not had a reboot but I havnt cranked on CZ for more than an hour will know for sure this weekend

may have to get a better fan for cpu cooler little hot for my blood now there goes the nice quiet evenings
 
I have a Swiftech MCX-462-V w/ a Panaflo 92mm M1A on it.. I'm at 44C load when the room is around 74 F.. Very quiet, and is still good for oc'ing..
 
Back
Top