Newly Built Comp, Need Help With Boot!

DJS2

Limp Gawd
Joined
Aug 25, 2005
Messages
344
Asus P5B-E mobo
HD 1: Raptor Drive w/ Windows XP
HD 2: 300GB sata storage drive

When I boot my computer sometimes it does not display on the monitor (orange light, not green).
I fixed this problem by unplugging the storage drive, booting it fine, and plugging it back in. Under my Bios under BOOT, i have:

Boot sequence:
1)Raptor Drive
2)CD-ROM
3)Disabled

Drives
1)Raptor Drive
2)Disabled

I thought my computer was unsure which drive had the OS to boot from so it wouldnt display on the monitor (at least thats how i fixed it). So I made those changes in BIOS and it STILL doesnt always show up on the monitor when i boot my computer.

Please help me experts of [h]ard! Thanks to everyone who tries to help.
 
Anyone have an idea? I would really appreciate some help.
 
Are we sure the storage drive works? Is it clear or does it have any old windows files on it? Try different jumper settings?
 
Yes the storage drive is in perferct condition, shows up in my computer, and im easily able to access the files on that drive. Since i plugged the storage drive sata into the "slave" sata slot on the mobo i thought i didnt have to mess around with jumpers?
 
Yes the storage drive is in perferct condition, shows up in my computer, and im easily able to access the files on that drive. Since i plugged the storage drive sata into the "slave" sata slot on the mobo i thought i didnt have to mess around with jumpers?

Sata should not have to worry about jumpers, but could be a wierd issue,
 
I recently have a PC that wouldn't boot when I hooked up a SATA drive. I found out that by default, the BIOS's SATA mode was automatically set to RAID. I had to change it to non-RAID before it would work. Possibly remove the SATA drive and boot-up and check the SATA BIOS settings?
 
Sata should not have to worry about jumpers, but could be a wierd issue,

The jumper on SATA drives is to force SATA150 speed instead of SATA300. If the SATA controller only supports SATA150, and you plug in a SATA300 drive, you may have problems. Hence the use of a jumper. This doesn't affect the OP, though, because A) raptors are SATA150, and B) the boards sata controller is sata300.

Try another sata cable... the problem seems intermittent. It may be a broken wire within the cable, or the hdd is going bad. Run some drive diagnostics on the storage drive.
 
Tried a new sata cable and im still having this problem.

Problem

1) I turn on computer, 75% of the time everything seems to start booting up fine (listening to the hard drive, and watching LED lights) but absolutely NOTHING shows up on my monitor. Sometimes it takes up to 4-5 times of me powering the comp on/off for it to finally "click" and have the monitor display what its supposed to. I really want this thing working flawlessly.. Please Any more suggestions? Bios setting?
 
Do you have an extra VGA/DVI monitor cable or an extra video card to try to make sure it's not either of those two? Or perhaps a diferent PC you can hook the GPU and monitor up to?
 
I had the exact same problem recently where everything would boot up yet nothing would display on the monitor. I could even enter in password and windows would start (I'd hear the jingle) but nothing on the monitor. This was only a random problem and most times the monitor was ok. Tried different cables, checked the GFX card etct etc but still kepy happening.

Then one day last week the monitor just would not display at all and hasn't since. Its sitting in the corner gathering dust as I type. Tried my spare monitor (crappy analogue and dead pixel) and it works perfect with no intermittent problems. Good news is the monitor has a 3 year warranty and I'm a couple months inside. Bad news is I can't locate the recieipt:rolleyes:

Just a possibility.
 
UPDATE: It is now taking me 5+ times of powering it on/off for it to properly boot.

Do you have an extra VGA/DVI monitor cable or an extra video card to try to make sure it's not either of those two? Or perhaps a diferent PC you can hook the GPU and monitor up to?

I tried using a new DVI connector (the black one that converts it to the blue plug for the monitor). Could it be the video card do you think?

I had the exact same problem recently where everything would boot up yet nothing would display on the monitor. I could even enter in password and windows would start (I'd hear the jingle) but nothing on the monitor. This was only a random problem and most times the monitor was ok. Tried different cables, checked the GFX card etct etc but still kepy happening.

Then one day last week the monitor just would not display at all and hasn't since. Its sitting in the corner gathering dust as I type. Tried my spare monitor (crappy analogue and dead pixel) and it works perfect with no intermittent problems. Good news is the monitor has a 3 year warranty and I'm a couple months inside. Bad news is I can't locate the recieipt:rolleyes:

Just a possibility.

My exact problem. I think it may either be the graphics card or the monitor, im leaning towards the graphics card, any other suggestions?


Thanks very much to everyone, but id love more input.
 
Other suggestions... hm... but it really looks like a vidcard/monitor issue, lol... Did you run diagnostics on the drive? Did you run memtest overnight? what psu do you have? do you have a ups? if so, does it have avr? if you dont have a ups, is it plugged into a surge protector? did you try another power socket? do you have a spare psu you could try? this is all, of course, after you test the vidcard/monitor, lol.
 
Other suggestions... hm... but it really looks like a vidcard/monitor issue, lol... Did you run diagnostics on the drive? Did you run memtest overnight? what psu do you have? do you have a ups? if so, does it have avr? if you dont have a ups, is it plugged into a surge protector? did you try another power socket? do you have a spare psu you could try? this is all, of course, after you test the vidcard/monitor, lol.

Everything in my comp is new except the video card, monitor, and hard drives. I have a spare monitor to test but not sure how im gonna be able to test the vid card.
 
If it's not the monitor than I'd say buy a new vid card. Pick one up used on the forum and sell it back if you don't end up needing it. Odds are - you will! :D

Good luck man...
 
Take your GFX card and monitor to a friends or to work or something and try them on a different rig.
 
Thanks for all the ideas guys. Just recently within the past hour when im browsing web pages, i notice my monitor is changing colors... mainly from normal to a blueish tone. Kind of just flashes in between, barely being able to notice it. Im not sure if this could have anything to do with my problem though.
 
Just for reference, post your FULL specs....

The bluish tone to the monitor sounds "not good" lol.... I think everything is fine on the case side, sounds like your monitor isn't sensing input, so just unplug the monitor and then plug it back in, it should find the feed then.... that, or use your monitor controls to search for the proper input (DVI, analog, etc)... is the cable well shielded? Have you calibrated the monitor yet? ... the Blue thing is quite odd, I'm leaning towards a monitor problem. Is that monitor new?
 
Just for reference, post your FULL specs....
The bluish tone to the monitor sounds "not good" lol.... I think everything is fine on the case side, sounds like your monitor isn't sensing input, so just unplug the monitor and then plug it back in, it should find the feed then.... that, or use your monitor controls to search for the proper input (DVI, analog, etc)... is the cable well shielded? Have you calibrated the monitor yet? ... the Blue thing is quite odd, I'm leaning towards a monitor problem. Is that monitor new?
check your PSU.

Monitor is fine now. Probably a weird thing. All cables have been checked and securely plugged in. It is 1.5 years old.

Im thinking the problem is any of these:
  1. Bad Graphics Card
  2. Bad Monitor
  3. Unable to determine which hard drive (OS or Storage) to boot from

I am going to try a different monitor and report back.

Mobo: Asus P5B-E Mobo
CPU: E6400 C2D 2.14GHz
PSU: Corsair 520W
GFX: Leadtek 6800GT
Monitor: NEC 19" CRT
 
UPDATE - VIDEO

http://youtube.com/watch?v=0PptREbFThw (turn on sound for beeps).

Took 5 restarts to boot up. I cant identify the "beeps" with anything in my manual, can you help me? The beeps are played halfway through the video and at the very end.

beepcodes-1.jpg
 
Wow - never seen a video quite like that before......

UPDATE - VIDEO

http://youtube.com/watch?v=0PptREbFThw (turn on sound for beeps).

Took 5 restarts to boot up. I cant identify the "beeps" with anything in my manual, can you help me? The beeps are played halfway through the video and at the very end.

beepcodes-1.jpg
You've got one long beep followed by three short beeps, yeah?

Looked at Asus website and your BIOS should be an AMI. According to the information I've got (not from ASUS):

"1 Long, then 3 Short Beeps: Video error

Explanation: The BIOS is unable to access the video system in order to write any error messages to the screen.

Diagnosis: This is usually caused by a problem with the video card, or the memory on the video card. It can also be a motherboard issue.

* Troubleshoot the video card.
* If the video card is not at fault, troubleshoot the motherboard."





However, to confirm this you need to contact ASUS customer support as every mobo manufacturer makes alterations to the basic BIOS and it could mean something else.

Edit: Just visited another site and their saying that those beep codes mean a memory error. This is why you need to check with ASUS. Maybe offer to send them the link for your video nasty (beep codes)




Before you do this I recommend doing the following first:

1. Reset BIOS to default
2. Disconnect everything from the mobo (HDD, CD, DVD, USB, firewire, floppy, Soundcard, keyboard, mouse - literally everything.)
3. Just leave the core components connected - CPU, 1 module RAM only, GFX & monitor.
4. Have a close look at GFX, CPU, mobo to see with there are any bulging or blown caps, obvious signs of damage or any signs of burning.
5. Reseat these core components, attach monitor and try to boot (with only 1 RAM).
6 If you've got a big heavy heatsink check for any damage around the processor (caps knocked or mobo cracked) and check if it is 'shorting out' to anything
6. If that doesn't work try the RAM in the different slots.
7. If still no good try another stick of RAM in different slots.
8. Check if the PSU sounds ok or if any burning smell comes from it.
9. Try the core components plus PSU one by one on a friends system.

Good luck

Edit: I'm sure you no what you doing, but just in case.

Make sure you are earthed before touching any components to avoid any static discharge.
Disconnect PSU from mobo before removing any cards.

DO NOT OPEN PSU AS THERE IS HIGH VOLTAGE INSIDE THAT CAN KILL EVEN WITH THE POWER OFF.

Disclaimer: You accept full responsibility and liability for the maintenance you are about to undertake on your system and fully acknowledge that any injuries sustained or damage to your property is your responsibility only.
 
Thanks, im going to "reseat" everything and see how it goes. Could this also be a video card going bad?
 
Try getting it to POST with just the core components. If that is a success then check that it works 15-20 times.

If all goes well, then introduce RAM into slots increasing modules one by one and checking POST after each addition.

Then add Soundcard - check POST

Then add HDD1 - check POST
Then add HDD2 - check POST
Then add FDD - check POST
etc etc so on an so forth.

Basically your trying to eliminate where the fault is.

While this is being done maybe contacting ASUS costomer services for a description of the beep code error..
 
Try getting it to POST with just the core components. If that is a success then check that it works 15-20 times.

If all goes well, then introduce RAM into slots increasing modules one by one and checking POST after each addition.

Then add Soundcard - check POST

Then add HDD1 - check POST
Then add HDD2 - check POST
Then add FDD - check POST
etc etc so on an so forth.

Basically your trying to eliminate where the fault is.

While this is being done maybe contacting ASUS costomer services for a description of the beep code error..

Maybe I missed something, but I'm assuming he doesn't have onboard video available so if he can't get the display working there's no way to check POST.
 
I took everything out, and reseated it. This morning it booted fine on the first try (although it has done this before, and messed up later). When it does fault, nothing comes up (not even post). Thanks so much guys, hopefully my computer starts working better and if it doesnt ill start calling asus and such. Thanks for all the help!
 
Back
Top