New ATI Build Not Booting, Need Help

Jucius_Maximus

Weaksauce
Joined
Dec 30, 2006
Messages
66
Hello. I've been reading threads on hardforums for over a year now but this is the first time I actually have to ask for help. Been building / troubleshooting computers for over 10 years now so I can handle technical advice.

Been helping my bro with his new Christmas hardware and we are getting nowhere fast. The machine is simply not booting. Push the power button and the fans + HDDs spin up but there is NO beep and the screen remains blank.

This is my first experience with a PCI-E / Dual Core setup.

Specs:

ASUS M2R32-MVP ATX AM2 Xpress 3200
Athlon 64 X2 4200+ Dual Core AM2 Windsor 2.2GHZ 2X512KB 89W 90NM Retail
ATI Radeon X1650 Pro (PCI-E)
Corsair XMS2 TWIN2X2048-6400 2X1GB PC6400 DDR2-800 CL 5-5-5-12

I have tried 2 PSUs with it:

Antec TruPower 430W - Might be underpowered; I am using the 20/24pin converter for the power.

Fortron FSP FSP600-80GLC 600W EPS12V 24PIN Power Supply - Not underpowered; You must snap an extra 2x2 pin power connector onto the 20 pin power connector to make a 24 pin connector. (I have tested the individual voltages on this snap-on connector and they are correct.) But this PSU lacks the extra 2x2 pin 12V power connector that connects by the video cards - the mobo manual says this connector is essential otherwise the machine will not boot. (The Antec above DOES have this connector)

Things Already Tried:

1. Reset the BIOS data. - No effect (I removed the battery, shorted the jumper for 10 s and then replaced the battery after 20 mins.)

2. Try only with 1 stick of RAM and move it to all possible slots. - No effect.

3. Re-seat the CPU, HS, Video, Ram, etc. - No effect.

4. Swap the above power supplies - No effect.

5. Try multiple monitors, DVI/VGA converter, etc. - No effect.

Earlier on I was trying to boot it with the Fortron PSU without the extra 2x2 power connector and of course it was not working. Maybe that had a bad effect? I also kinda knocked one of the capacitors on the board a bit when I was reinstalling the heatsink during troubleshooting... it did not break but that made me uneasy... though the board was already showing problems before this point.

Any help as to what to do to get this machine running would be much appreciated.
 
Have you tried removing ALL the components save for the CPU and see if it gives you a beep code? Do you know if the board supports a voice output error code? If it does, you'll need to plug in some analogue speakers to hear what the board has to say to you.

 
DamienThorn said:
Have you tried removing ALL the components save for the CPU and see if it gives you a beep code? Do you know if the board supports a voice output error code? If it does, you'll need to plug in some analogue speakers to hear what the board has to say to you.

Thanks for the info, I have removed everything except the CPU, one stick of RAM, the video and the floppy. (I have also swapped out the video.)

Would have to try booting it again if I wanted to do it naked except for the CPU.

Have not tried for an audio error message and not sure if the board even supports that feature, but I will have to look into it.
 
This is an issue that only rarely happens anymore, but it's also possible that the video is trying to output to the PCI (not the PCIe bus) - you could try swapping a PCI video card and seeing if that helps at all.

 
DamienThorn said:
This is an issue that only rarely happens anymore, but it's also possible that the video is trying to output to the PCI (not the PCIe bus) - you could try swapping a PCI video card and seeing if that helps at all.

Thanks for the suggestion... that was one of my first thoughts as well but unfortunately I was not able to dig a PCI video card out from anywhere. We sold a lot of the legacy gear some years ago so that's an avenue I can't test. :(

At this point I think the main option is the RMA the board, so I will see what happens tomorrow when the dealer is open.
 
This story has a happy ending...

My family members ended up taking the gear to a local shop, and those people actually got it working.

The problem was ... (please finish chewing anything before you continue) ...

... The CPU was not pushed firmly enough into the socket. (WTF!!) That's what they said after they got it to boot.

To me this is deeply embarassing because I am the one who installed the CPU.

Now I did not know that this sort of thing could happen because I have always just dropped the chip into the socket and closed the lever. I did not know any pressure was required.

Do the dual core chips need some extra force or something?
 
Back
Top