Need urgent help new comp wont start!

dare8787

n00b
Joined
Feb 15, 2008
Messages
9
hi guys
im very disperate and need help!

i just build new comp (for the first time) and did everything by the book.
everything vent smooth!
until......

when i turn ON comp i get black screen saying something about phoenix bios,dual processor,etc... and at the end says PRESS DEL for setup or ESC for exit.

Now here problem start!
my keyboard is ON,all lights on board are ON (usually they turn OFF after few seconds), BUT i cant do enything!
It does not respond,pressing any key (ESC or DEL) does not do anything,im just stuck on that blac screen.

Now, i noticed that on screen does not says anything about HD or DVD.Is that normal?
i can see it only detected my processor!.

Only diference i have between this comp and my old one is that new HD i conected via sata cables,and my old HD is using normal cables.

anyone got any idea what it could be?
i really want to save 100 bucks and not take it to frys electronic for repair .
thank u in advance

parts used-
EVGA 132-CK-NF78-A1 LGA 775 NVIDIA nForce 780i SLI ATX Intel Motherboard
CORSAIR XMS2 4GB(2 x 2GB) 240-Pin DDR2 SDRAM DDR2 800 (PC2 6400) Dual Channel Kit
SATA 300 HARD DRIVE (can this be a problem?)
PSU 500

Also i forgot to say pressing buton on my DVD drive to open it does not work.im not sure if that is also related to my problem
 
If you can't access anything with the keyboard, power down the pc by holding the power button for 5 secs till it turns off. Then, try clearing the cmos setting with the jumper setting on the mobo. Also, try using another keyboard to the computer.
 
You need to list all of the parts in your rig... and be more specific as to which hard drive and power supply you are using.

Also, try using a PS/2 keyboard and mouse for the initial setup. Many motherboards have settings that allow the use of USB keyboards and mice at the boot screen, but they aren't enabled initially.

Follow HardwareGuru's advice: Turn off the computer, reset the CMOS, recheck all of the cable connections, use a PS/2 mouse and keyboard, and then try and turn it back on.

If that doesn't work, then you may need to attempt a "bare-bones" build -- the motherboard, one stick of RAM, the video card (or, preferably, the onboard graphics chip), and the power supply -- to start narrowing down what the problem is.
 
guys i found the problem! but now i dont know what to do!

problem is - my CORSAIR XMS2 4GB(2 x 2GB) 240-Pin DDR2 SDRAM DDR2 800 (PC2 6400) Dual Channel Kit .

when i have two sticks of memory in my computer i have problems i described before!
when i leave ONLY one everything is fine,i can pass firs checking screen and go further.

so bottom line,my motherboard does not like this dual channel sticks together!

BUT,if i use my old memory ( 2 x 1GB) EVERYTHING IS FINE!


So now,is it something wrong with my new dual channel memory?
(2x2 x 2GB) ?
i bought them from newegg
 
Either the memory sticks are defective and you have to RMA them which is the most likely situation, or your BIOS default is undervolting the sticks and it's giving you freezes after POST, which has happened to me when I have booted up. However I see it as the former b/c usually you'd only be undervolting if you are O/Cing, not on your first boot up. What are your sticks rated at? Try to enter your BIOS and see what voltage its giving your memory sticks.
 
Since no one's done it yet, I'll ask the obvious/dumb question. When you have the sticks installed, you are absolutely sure that you have them in the right slots? For dual channel setups I know some boards are different, some require them to be next to each other, some color code the slots, etc. Take a very close look at your MB docs and determine which is right for you. If you do have it installed correctly, I'd agree with the above posters that your RAM is probably bad.
 
Both sticks should be able to run together, even if they're not properly configured for dual channel mode. But to only have one of the sticks work, whereas both sticks from a different pair of RAM function with no problems, suggests that the RAM is defective.
 
thank u very much for your help guys.
memory is defective.
i just put both sticks in my friends computer and it wont even start to boot.
called newegg and they issued me RMA.
now im scared to order same memory again.
any suggesions what to get?
thank you
 
Back
Top