Need tips for raising Bclock

MaxBurn

[H]ard|Gawd
2FA
Joined
Nov 14, 2004
Messages
1,134
Motherboard is GA-X58A-UD5 r1.0. CPU's are i7 950 and Xeon W3530. Basically I have found that I just hit a wall at about 160 Bclock so I dropped the multipliers on the CPU and memory to find that it is definitely the Bclock holding me back somewhere.

200Bclock / CPUx14@2.8ghz / memx8@1600 / uncore x16=3200 / PCIE 100
All relevant volts are locked to stock values.

Looking for advice on what to tweak to get Bclock 170~.200
 
Hi there,those CPU all hit 3.8MHZ wiithout breaking a sweat,past 3.8 can be a different story.I will try to help,how much ram do you have and heres a template to get you started.

Try this for starters,Say on the 950.
Code:
Advanced CPU Features:
CPU Clock Ratio ................................ [21x]
Intel(R) Turbo Boost Tech .................. [Disabled]
CPU Cores Enabled ............................ [All]
CPU Multi Threading .......................... [Enabled]
CPU Enhanced Halt (C1E) ................... [Disabled]
C3/C6/C7 State Support .................... [Disabled]
CPU Thermal Monitor ......................... [Enabled]
CPU EIST Function ............................ [Disabled]
Virtualization Technology ................... [Enabled] << Disabled if you do not use Vmware or Virtual PC Bi-Directional PROCHOT ..................... [Enabled]


Uncore & QPI Features:
QPI Link Speed .............................. [Auto] (4.8GHz)  << Set manually x36 
Uncore Frequency .......................... (Always 2x memory Multi or 2x +1)  << Set manually 16-18Isonchronous Frequency ..................[Enabled]


Standard Clock Control:
Base Clock (BCLK) Control ................ [Enabled]
BCLK Frequency (MHz) ..................... 180 for now
PCI Express Frequency (MHz) ........... [Auto]  << Set 100

C.I.A.2 [Disabled]

Advanced Clock Control:
CPU Clock Drive ..............................[800mV]
PCI Express Clock Drive ................... [900mV]
CPU Clock Skew ............................. [0ps]
IOH Clock Skew ............................. [0ps]


Advanced DRAM Features:
Performance Enhance ...................... [Turbo]   Try Standard for now (X.M.P) .........                                    [Disabled]
System Memory Multiplier (SPD) ........ [Auto]  << Set 8 = 1440Mhz for now
DRAM Timing Selectable (SPD) .......... [Auto]  << Set Expert, then set each channel's main timings and CMD rate one by one

Channel A + B + C

Channel A ,B,C Timing Settings:
##Channel A Standard Timing Control##
CAS Latency Time ...................... Set 9 now, try 8 later
tRCD ..................................Set 9 now, try 8 later
tRP ...................................Set 9 now, try 8 later
tRAS .................................Set 24 now, try 20 later

Below values may be left in Auto if you like, generally this is fine.

##Channel A Advanced Timing Control##
tRC ........................................ (Should be = tRAS + tRP or above for stability)
tRRD .......................................
tWTR ...................................... (Must be Write to Read Delay/Same Rank - (tWL + 4)
tWR ........................................
tWTP ....................................... (tWTP Must = tWR + tWL + 4)
tWL ........................................ (tWL Must be CAS Latency -1)
tRFC .......................................
tRTP .......................................
tFAW ......................................
Command Rate (CMD) ................  Set 1T

##Channel A Misc Timing Control##
Round Trip Latency ...................

B2B CAS Delay ..........................


Advanced Voltage Control:

CPU
Load Line Calibration ................. [Auto] Enabled
CPU Vcore ............................. [Auto] (SET 1.29375V - 1.31) with 950 may need higher
QPI/VTT Voltage ...................... [Auto] (1.175V)  leave auto for now ,but auto is not enough for 12GB CPU PLL 1.800v ........................ [Auto] (1.800V) leave auto for now

MCH/ICH
PCIE 1.500v ........................... [Auto] leave auto for now
QPI PLL 1.100v ....................... [Auto] leave auto for now
IOH Core 1.100v ..................... [Auto]  leave auto for now
ICH I/O 1.500v ....................... [Auto]  leave auto for now
ICH Core 1.1v ........................ [Auto]  leave auto for now


DRAM
DRAM Voltage 1.500v .................. [Auto]  << Set to dram spec, normally this is 1.65V, so set 1.66 for now 12GB needs way more
DRAM Termination 0.750v [AUTO]
Ch-A Data VRef. 0.750v [AUTO]
Ch-B Data VRef. 0.750v [AUTO]
Ch-C Data VRef. 0.750v [AUTO]
Ch-A Address VRef. 0.750v [AUTO]
Ch-B Address VRef. 0.750v [AUTO]
Ch-C Address VRef. 0.750v [AUTO] 

Some fault codes
0X00000050 << Incorrect Memory Timing/Freq or Uncore Multi
0X00000124 << Incorrect QPI/Vtt Voltage (To Much/Not Enough)Also high GPU overclocks
0X00000101 << Not enough Vcore Voltage
 
Thank you SO much, this bit at the end there was very revealing:

Some fault codes
0X00000050 << Incorrect Memory Timing/Freq or Uncore Multi
0X00000124 << Incorrect QPI/Vtt Voltage (To Much/Not Enough)Also high GPU overclocks
0X00000101 << Not enough Vcore Voltage

I was seeing constant 124 errors so I will focus on that QPI volts.

My QPI volts are locked to default at the moment, also the multiplier is locked to x36. I will search around to see what others are using.

My memory is in sig, just 6gb. It is rated at 1.5v (at XMP 1600 speeds) and it is locked to that. Both my memory and CPU are underclocked at the moment while I work on getting the Bclock stable in a mhz range I need. I don't really figure on going past 200mhz Bclock but I could really use it to get close.
 
Hi there OK with error 124 keep in mind that the QPI volts and memeroy voltage need to be with .5volts of each other.

You can go as high as 1.6 QPI and still be safe.

Getting 200 blc is possible be real hard on some boards,but that board you shouls be able to hit 210-215 with the correct volts.

The 950 will need high Vcore volts to go that high.

With everything at default like I posted you should hit 3800 easy.Play around and I can give you other numbers for close to 200blc if you can not get it.
 
Well I got to 180 Bclock which is further than I ever got before. Still won't hit 200 though. CPU and Memory still underclocked at 2.8 and 1440.

At first I messed up and upped the QPI PLL which seemed to actually help so I left that at 1.2. I read elsewhere that 1.35 was the safe max for QPI/VTT? I went up to 1.30 QPI/VTT which didn't get it stable at 200 Bclock.

Edit: Oh I am not getting the 124 error anymore either, now it seems to hard lock on the four colors screen that win7 gives you before you enable video and go to the login screen. Guess that's still progress.

This is what I have now:

Load Line: Standard
Vcore: 1.3 (think this is xeon default)
QPI/VTT: 1.295 (defaults at 1.175 looks like)
CPU PLL: 1.8

PCIE: 1.5
QPI PLL: 1.2 (stock is 1.1)
IOH Core: 1.1
ICH I/O: 1.5
ICH Core: 1.1

Memory: 1.5 (my memory is rated at this for XMP 1600, works fine so I didn't raise it)
Dram Termination: .750
A,B,C Vreff .750
 
180 blc is easy.

As far as the safe voltages,they all can be pass recommended limits with no problems.
EDIT:From the master of gigabyte to ease your mind about voltages some.
http://forums.tweaktown.com/gigabyte/33454-post-i7-core-temps-here-5.html#post312297

I am wondering why you want 200blc when say the 950 has a multi of 23.OR you just want your ram to run @1600.

Anyway 200blc may be hard.Since I do not have your CPU ,board in front of me its hard to judge.
MAke sure you check CPU temps and raise VCORE .05 volts until it post and runs upto 1.5 volts if you have great cooling.And may be needed for 200blc

Set your settings to what I listed below.

Code:
Advanced CPU Features:
CPU Clock Ratio ................................ [20x]
Intel(R) Turbo Boost Tech .................. [Disabled]
CPU Cores Enabled ............................ [All]
CPU Multi Threading .......................... [Enabled]
CPU Enhanced Halt (C1E) ................... [Disabled]
C3/C6/C7 State Support .................... [Disabled]
CPU Thermal Monitor ......................... [Enabled]
CPU EIST Function ............................ [Disabled]
Virtualization Technology ................... [Enabled] 
Bi-Directional PROCHOT ..................... [Enabled]


Uncore & QPI Features:
QPI Link Speed .............................. [36x] 
Uncore Frequency ..........................  [16]
Frequency ..................[Enabled] 

Standard Clock Control:
Base Clock (BCLK) Control ................ [Enabled]
BCLK Frequency (MHz) ..................... 200 
PCI Express Frequency (MHz) ........... [Auto]  << Set 100

C.I.A.2 [Disabled]

Advanced Clock Control:
CPU Clock Drive ..............................[800mV]
PCI Express Clock Drive ................... [900mV]
CPU Clock Skew ............................. [0ps]
IOH Clock Skew ............................. [0ps]


Advanced DRAM Features:
Performance Enhance ...................... [Standard ]  
(X.M.P) .........                                    [Disabled]
System Memory Multiplier (SPD) ........ [8 ]  Set 8 = 1600MHZ
DRAM Timing Selectable (SPD) .......... [Expert]  Channel A + B + C

Channel A ,B,C Timing Settings:
##Channel A Standard Timing Control##
CAS Latency Time ...................... Set 10
tRCD ..................................Set 9 
tRP ...................................Set 9 
tRAS .................................Set 28 
Below values may be left in Auto if you like, generally this is fine.

##Channel A Advanced Timing Control##
tRC ........................................ (Should be = tRAS + tRP or above for stability)
tRRD .......................................
tWTR ...................................... (Must be Write to Read Delay/Same Rank - (tWL + 4)
tWR ........................................
tWTP ....................................... (tWTP Must = tWR + tWL + 4)
tWL ........................................ (tWL Must be CAS Latency -1)
tRFC .......................................
tRTP .......................................
tFAW ......................................
Command Rate (CMD) ................  Set 2T

##Channel A Misc Timing Control##
Round Trip Latency ...................

B2B CAS Delay ..........................


Advanced Voltage Control:

CPU
Load Line Calibration ................. [enabled] 
CPU Vcore ............................. [1.35] 
QPI/VTT Voltage ...................... [1.53] 
CPU PLL 1.800v ........................ [1.88] 
MCH/ICH
PCIE 1.500v ........................... [1.54]
QPI PLL 1.100v ....................... [1.4] 
IOH Core 1.100v ..................... [1.3]
ICH I/O 1.500v ....................... [1.58]  
ICH Core 1.1v ........................ [1.22]  

DRAM
DRAM Voltage                                             1 .65 is the min here not 1.5v
DRAM Termination 0.750v [AUTO]
Ch-A Data VRef. 0.750v [AUTO]
Ch-B Data VRef. 0.750v [AUTO]
Ch-C Data VRef. 0.750v [AUTO]
Ch-A Address VRef. 0.750v [AUTO]
Ch-B Address VRef. 0.750v [AUTO]
Ch-C Address VRef. 0.750v [AUTO] 

Some fault codes
0X00000050 << Incorrect Memory Timing/Freq or Uncore Multi
0X00000124 << Incorrect QPI/Vtt Voltage (To Much/Not Enough)Also high GPU overclocks
0X00000101 << Not enough Vcore Voltage
 
Last edited:
Thanks, will do later on.

As far as the "why" I was thinking I had a crappy 950 when I couldn't get past 155x24 at 3.7ghz. So I picked up a W3530 thinking these are binned better and I was stumped when it too wouldn't get past 155x22 at 3.4ghz. So I was left with Bclock being the limiting factor and some testing with underclocking on the CPU and memory confirmed it.

So now I am exploring the limits on my Bclock and defining what it takes to do certain speeds. Once I am concrete on that I will then again start to explore what these CPU's can do.

It's a process. Also I am still thinking the xeon will post some better numbers than the 950, but its going to need a big Bclock to do it.
 
Thank you, these voltage settings are what got me stable at 200 Bclock.

QPI/VTT Voltage ...................... [1.355]
CPU PLL 1.800v ........................ [1.88]
MCH/ICH
PCIE 1.500v ........................... [1.50]
QPI PLL 1.100v ....................... [1.4]
IOH Core 1.100v ..................... [1.3]
ICH I/O 1.500v ....................... [1.58]
ICH Core 1.1v ........................ [1.22]
 
Back
Top