Need some [H]elp with crossfire.

Ph.D

Limp Gawd
Joined
Jul 9, 2010
Messages
190
With help from this community I upgraded my PC not too long ago.
I went from a single 6950 2GB (unlocked to 6970 shaders and overclocked) to a crossfire setup with that card and an MSI 6970 lightning.

I made the 6970 the primary card but I'm a little concerned not everything is working properly.
I use Afterburner for my tuning and do not use CCC because it messes with my overclocks.

GPU-Z tells me crossfire is enabled and I use the latest (non-beta) drivers from AMD. Is there anything I should be worried about? My unlocked 6950 2GB used to run at 900MHz core clock and 1400 MHz memory clock.

Do I have to configure Afterburner in any specific way to get the best results?
Game performance has not been all that great. I know many games do not support crossfire/SLI that well but still...
Is it normal that the unlocked 6950 seems to be automatically downclocked because of the crossfire setup (see image)?

Sorry of my questions are elementary, but this is the first time I've used a multi-GPU configuration.

qTx0N.png
 
Have not been on Xfiah for a little bit but I did previously run 2 shader unlocked 6950's so I'll give it a whirl. Xfiah will always default both cards to the speed of the slowest GPU. When you unlocked the shaders on the 6950 did you just unlock them or did you flash to a 6970 BIOS? Using slightly dissimilar cards can cause issues. Also, under the general tab in AB be sure to check the box for something like "sync settings of similar GPU's".
 
Have not been on Xfiah for a little bit but I did previously run 2 shader unlocked 6950's so I'll give it a whirl. Xfiah will always default both cards to the speed of the slowest GPU. When you unlocked the shaders on the 6950 did you just unlock them or did you flash to a 6970 BIOS? Using slightly dissimilar cards can cause issues. Also, under the general tab in AB be sure to check the box for something like "sync settings of similar GPU's".
I flashed it to the 6970 BIOS.
I currently have the "Synchronize settings for similar graphics processors" option unchecked.
Because they are not exactly the same cards I thought it might be bad to do so.
 
I flashed it to the 6970 BIOS.
I currently have the "Synchronize settings for similar graphics processors" option unchecked.
Because they are not exactly the same cards I thought it might be bad to do so.

That's probably your issue then. They will both default to the slower speed.
 
The basic 6970 lightning runs at 940MHz core clock and 1375MHz memory clock and my 6950 ran at 900 core and 1400 memory so maybe those 40MHz are causing the problem.
On the other hand, since going crossfire, when I check afterburner it always seems to be running the 6950 at much lower specs (as you can see in the image). Not sure why that is...
 
The basic 6970 lightning runs at 940MHz core clock and 1375MHz memory clock and my 6950 ran at 900 core and 1400 memory so maybe those 40MHz are causing the problem.
On the other hand, since going crossfire, when I check afterburner it always seems to be running the 6950 at much lower specs (as you can see in the image). Not sure why that is...

It almost seems like your second 6950 is running in a gimped mode, like higher then 2D but lower then 3D clocks...:confused:..I would remove the ATI drivers using Driver Cleaner Pro, and do a fresh install of them, along with a fresh install of AB..See what happens from that point and report back.
 
It almost seems like your second 6950 is running in a gimped mode, like higher then 2D but lower then 3D clocks...:confused:..I would remove the ATI drivers using Driver Cleaner Pro, and do a fresh install of them, along with a fresh install of AB..See what happens from that point and report back.
I have removed the drivers, used Driver Sweeper and installed the latest beta drivers and CAP.
So I am now running the 12/3/2012 12.11 beta drivers and 12/3/2012 12.11 CAP 2.

The result is the same.
6970 MSI Lighting:
BcCbv.png


6950 Asus:
e8c3a.png




I can manually force the 6950 to run at my old overclock but it doesn't seem to do it automatically and resets when I restart the PC.




EDIT:
I'd also like to know if it's a better idea to keep their separate clocks (940core/1375memory for the Lightning and 900core/1400memory for the Asus) or if I should try to make both run at the same clocks and then check the "Synchronize settings for similar graphics processors" box in Afterburner as mentioned above.
 
Last edited:
I'd disable ULPS. Also, I'd turn on Unofficial overclocking.
Power saving is off and unofficial overclocking is on. I wouldn't be able to get those clocks on my 6950 without turning on unofficial overclocking.
And if I don't disable power saving my screen starts glitching out.
 
Tell Afterburner to show the GPU/memory speeds - I had problems for a while on my HD6950 Crossfire (before I went quadfire) where the second card was stuck at idle clocks so the first card would run at something like 8% load to match the second card. To fix it I had to manually turn off Crossfire and then turn it back on. All this was due to the fact that the monitors I had were plugged into the video card *NOT* closest to the CPU (due to the way the PCI-E slots were laid out on my motherboard). When I got a HD6990 to complement the two HD6950's I rearranged the video cards so that the monitors were plugged into the card closest to the CPU and all my Crossfire problems went away.
 
Tell Afterburner to show the GPU/memory speeds - I had problems for a while on my HD6950 Crossfire (before I went quadfire) where the second card was stuck at idle clocks so the first card would run at something like 8% load to match the second card. To fix it I had to manually turn off Crossfire and then turn it back on. All this was due to the fact that the monitors I had were plugged into the video card *NOT* closest to the CPU (due to the way the PCI-E slots were laid out on my motherboard). When I got a HD6990 to complement the two HD6950's I rearranged the video cards so that the monitors were plugged into the card closest to the CPU and all my Crossfire problems went away.

Interesting problem, I do have the monitor plugged into the GPU nearest to the CPU though. And I'm using one monitor.

I'll fiddle around with it some more. What's your (and everyone else's) opinion on my earlier question?
I'd also like to know if it's a better idea to keep their separate clocks (940core/1375memory for the Lightning and 900core/1400memory for the Asus) or if I should try to make both run at the same clocks and then check the "Synchronize settings for similar graphics processors" box in Afterburner as mentioned above.
I'm sure someone running 4 GPUs at once will know more about it than I do. :D
 
Still check the clocks under load - your scaling problems look a lot like the secondary card clocks do not ramp up.

The clocks don't have to be synchronized to work. That way you don't accidentally overclock one of the cards.
 
It does seem to ramp up when I play a game.

I think I actually got the second card to stay at its original clock speed too. Now I just need to figure out if I should try to make both run at the same speeds and use synchronize or leave them at their respective clocks.
 
I don't think anyone's asked but how does CCC "mess with your overclocks"?

I have 2 6950 2GB cards unlocked with 6970 shaders and overclocked in crossfire (870/1330) and they work flawlessly with the CCC. I have afterburner installed for monitoring purposes.

Have you tried just using the CCC? Does it report the same clocks as AB?

Also I seem to get the best performance with the clocks synchronized. One of my cards clocks higher than the other but with them running the same the FPS is more "stable".
 
I don't think anyone's asked but how does CCC "mess with your overclocks"?

I have 2 6950 2GB cards unlocked with 6970 shaders and overclocked in crossfire (870/1330) and they work flawlessly with the CCC. I have afterburner installed for monitoring purposes.

Have you tried just using the CCC? Does it report the same clocks as AB?

Also I seem to get the best performance with the clocks synchronized. One of my cards clocks higher than the other but with them running the same the FPS is more "stable".
Whenever I have both CCC nullifies the clocks I set in Afterburner. And since CCC cannot overclock the GPUs nearly as precise as Afterburner (especially when it comes to fan speed profiles) I had to uninstall it so that it would not override Afterburner.
Sadly that takes away some of the handier functions of CCC like how you manage multi-screen setups but I guess I'll have to live with that.

... Unless you happen to know why CCC refuses to play nice with Afterburner for me. ;)


Thanks for your advice on synchronization as well. I don't think my 6950 can handle 940MHz on the core so I may have to weaken the 6970 a bit, although the 6970 apparently can't manage to run at 1400MHz on the memory like my 6950 at the same voltage...
 
Back
Top