Need help troubleshooting a problem with a new build

1Wolf

Limp Gawd
Joined
Jul 10, 2007
Messages
439
Greetings,

I would really appreciate any help anyone could give in troubleshooting a problem I'm having with a new build.

A few weeks ago I ordered and began my very first build, a gaming machine. Parts arrived and everything went real well. System booted up just fine. I configured the BIOS and installed windows XP. Everything was still fine.

First....some info about my system:
Mobo: EVGA nVidia nForce 680i SLI (A1 series)
PSU: Thermaltake Toughpower 1200W
CPU: Intel Q6600 2.4 Ghz
Memory: 4 GB DDR2-800 Corsair XMS2
Video Card: EVGA GeForce 8800 Ultra
Sound Card: Creative Soundblaster X-Fi Xtreme Gamer
Hard Drives: 2 Seagate 7200.10 320 GB drives (RAID 0 stripe)
ODD: 1 SATA Samsung DVD Burner & 1 IDE Samsung DVD Burner
FDD: Sony Floppy Drive

This system has not been overclocked in any way.

This same system has been running for several weeks now as I installed drivers, setup windows, etc. etc. in my free time. Haven't had one glitch. The thing had run for many hours on end, core temperatures were always right around 40 degrees. Everything seemed dandy.

Then, yesterday I get home from work and go to power on the machine. It starts...POSTS...starts to load windows (Windows XP splash screen) and then it just literally dies....as if someone yanked the plug. The mobo was still receiving power as the little blue and amber LED's were still lit. Everything else was dead though.

I tried to turn it on again, and again it POSTED fine, and booted all the way into windows. It stayed there about 5 minutes and then just croaked again. Same as before. I hit the power button again and this time it posted and died a few seconds later. Tried again and the next time it didn't even make it to the POST beep.

I turned off the power to the power supply...let it sit for a while...then tried it again. Same thing...sometimes it would POST and get to windows and then die, sometimes it would post and get to windows and run for a while and die, and sometimes it would run just long enough to spin the fans up and then die.

One of those times that it POSTED and then died...there was a message on the screen that said something about resetting the CMOS or checksums or some such. The system died and it disappeared to quickly for me to get a good look at it.

So...I reset the BIOS using the CMOS jumpers...and I was able to get the system up and running. I reconfigured the BIOS to my old settings....and it ran fine in windows for about an hour. I thought the problem was solved when blammo...it died again and started that same strange behavior again.

This time it would run long enough for me to get into the BIOS and make changes though. I researched similar problems out on the net and alot of folks mentioned checking PSU's and bad Mobo's...but it just seemed to me that if one of those went bad...I'd see more consistent failures. So next I tried memory.

My memory was the nVidia SLI-Approved stuff. When installed with "SLI Approved" set to disabled in the BIOS (the default) the memory timings defaulted to 5-5-5-18. In the BIOS, I had set "SLI Approved" to enabled and the BIOS reset the memory timings to new "optimal" defaults of 4-4-4-12.

The system had run fine for weeks on these settings. However, when I received the weird unstable system problems I described above...I went into the BIOS and reset "SLI Approved" to disabled. This reset those memory timings back to 5-5-5-18. Sure enough...system boots fine and has been running for 8 or so hours without problem. I shut it down this morning and started it back up....started up and ran fine.

Anyone have any idea what I should do about this? Anyone have any idea what could have happened? Why would the system run great on the 4-4-4-12 timings for weeks and then just one day decide not to anymore? Is some of that RAM possibly going bad? Is it possible that just out of bad luck I received RAM that was functioning...but very unstable? I didn't push those RAM timings beyond the manufacturer's recommended and SPD detected 4-4-4-12.

I let the BIOS run the full memory test and it didn't show any problems....is there some software I should be running to test the memory outside of what the BIOS offers?

Or...am I just looking in the wrong place....is it just plain dumb luck that the system started running under the more relaxed timings and the problem most likely has nothing to do with the memory itself....but perhaps the motherboard?

I apologize for the long post but I wanted to give all the information that I could. Any and all help and advice would be greatly appreciated. Thanks!!!
 
When in the SLI approved settings did the board automatically increase the memory voltage to 2.0 or 2.1 V ? If it did then you need to post in the memory section, mention what the Voltage is in SLI mode and contact Corsair for an RMA. Be sure to mention that it is the SLI mode that is causing the issue, the EPP in the SPD chip may not be properly programmed.

The reason I say post in memory section is the Corsair reps hang out there and might have a solution for you so make the title of your post - Is a Corsair RMA needed ? or something like that. Do include all the excellent details of this post and add the voltage information.

If the memory is not automatically upping the memory voltage to 2.0 or 2.1V do so manually in the bios and it more than likely will solve your issue.

(Corsair XMS is still under warranty up to and including 2.1V and likes the extra jucie when running at tight timings. )

Memtest86+ is the tool most of us use to test memory. A run of that and the results added to the post will help your case. Corsair will have no problem issuing you an RMA but its worth the effort to test and let the rep take a look at the issue, it might save 2 weeks without memory. A CD burned the the memtest .iso file (using nero or something like it) is always handy to have around, it has its own OS and you just set the machine to boot from CD and it runs automatically.

http://www.memtest.org/
 
Great! Thanks so much for the help and info Bill.

When in the SLI approved settings did the board automatically increase the memory voltage to 2.0 or 2.1 V ? If it did then you need to post in the memory section, mention what the Voltage is in SLI mode and contact Corsair for an RMA. Be sure to mention that it is the SLI mode that is causing the issue, the EPP in the SPD chip may not be properly programmed.

Yup. Thats exactly what happened. The memory voltage was indeed increased automatically. I'll duplicate my post in the memory section and change the title.

Memtest86+ is the tool most of us use to test memory. A run of that and the results added to the post will help your case. Corsair will have no problem issuing you an RMA but its worth the effort to test and let the rep take a look at the issue, it might save 2 weeks without memory. A CD burned the the memtest .iso file (using nero or something like it) is always handy to have around, it has its own OS and you just set the machine to boot from CD and it runs automatically.

Thanks! I'll snag that as soon as I get out of work tonight and give it a shot.

Thanks again for all your help. Its greatly appreciated! When you're 'new' to this you feel a bit like a babe in the woods when strange mysterious things go wrong ;)
 
I agree with the argument,and maybe the memory voltage is to blame....but

what is the voltage normally????
do you really need that special SLI memory enabled????
especially if the system is rock solid when all you have to do is disable SLI memory.
I have a 680i board and I run it with SLI memory disabled and just let the board decide what's best. It sounds funny to me...... because the nominal voltage for XMS is 2.1, my board likes to run the memory at 1.94.

If you dont want to step into a big "goat-rope" I'd just disable the setting and call it a day.
 
Update:

Well....here are my latest troubleshooting steps and the results. Hopefully maybe some of these results or something I did or what not might give someone reading this some inkling of what was going on.

First off, I posted in the Corsair Support forums the same post I placed here. RAM GUY answered from Corsair and seemed to feel that it sounded like a powersupply or motherboard problem. What do I know...I'm sure he's right. It just seems odd to me that the computer would run stable without anything being changed for weeks and then just begin this odd behavior. Also, If it was the powersupply or the motherboard....I'd think that once the mysterious 'power offs' started...they would continue...especially if the powersupply or motherboard had gone 'bad'. However...the system seems to be running 'fine' now. After changing the SLI-Ready settings I mentioned in my previous post...the system runs stable again. Also, the Corsair Support Rep mentioned that he felt I should underclock the DDR2-800 RAM to 667 because I have 4 1 Gig sticks. He made that sound like it would increase stability and that I take some sort of performance hit for using 4 sticks instead of two. I'm not quite at the stage in my 'learning' yet where I understand that. I'm not sure if that is good or bad advice.

Secondly, I did some more poking around on the net...here at HardOCP forums and on the Corsair forums and some other places. I'd read some folks saying that you CANNOT set SLI-Ready memory to "enable" in the BIOS if you have 4 sticks/4 Gigs of RAM. So I thought perhaps that was my problem.

So, when I got home, I followed BillParish's advice and downloaded MemTest86. I wasn't sure if I should remove memory or leave it in...so I just left it all in and figured I'd test it all at once. I left Memtest86 run for a good 8 hours and it didn't find any errors or problems.

Next, I went into the BIOS and I left SLI-Ready memory disabled. However, I went over to the memory settings and manually set the memory timings from the default 5-5-5-18 to the 4-4-4-12 that setting SLI-Ready to enabled normally sets. Also, those are the manufacturer listed timings in the documentation for that memory. Also...I went over to memory voltages and manually changed the memory voltage from the default 1.850 volts to 2.1 volts.

I ran the computer, doing various things (Watched a movie, did some work, etc.) for several hours and there wasn't even a hiccup.

Next...before bed....I set Memtest86 to run again. I left it run all night...it made around 11 passes. Not one error or problem.

This morning before work...I booted into windows and checked my core temps with CoreTemp. All 4 cores were between 40-45. I shut down and restarted the machine several times...each time was flawless.

I also ran 3DMark2006 to see if I'd get results that were similar to results I've received in prior testing. I got 12086 3D Marks....pretty close to the same I'd received in previous tests (By the way...I hope 12086 is around the score I SHOULD be getting with my system configuration and hardware).

So....thats the information I have to add this morning. If any of the above leads anyone to any conclusions or theories...please share them. I'd love to figure out whats going on. In the future...my next step is overclocking to around 3.0 Ghz or so....and I really want to make sure everything else is stable and running properly before starting the next steps.

Thanks again!
 
Back
Top