Need help ASAP. PH II x4 BE

BioInclined

Limp Gawd
Joined
May 23, 2011
Messages
332
Ok, try to keep it short and to the point.
My system info is below. I am not OCed. Today I did DL AMD OverDrive to consider bumping my system a bit, maybe to 3.4GHz max. I ran the novice level one test, then the auto clock, it seemed to have taken me to 3.3GHz. I ended up "un-OCing" it, setting it back to default clocks and let it be.
Then the issue, maybe 1 hour or so later(when i noticed), my little windows 7 gadget was only showing 800MHz for my clock and not moving.
Upon inspection, i found my new AMD/ATI Overdrive(don't know whats so great about naming these things that) driver which was a ATI set up one for the card, has a settign for my processor to determine what load i want it to max out on, it seemed to be in or out of game option. It was set to 800MHz max. So i reset it to 800MHz-3200MHz.
I then noticed my temps are up as well. Not but 1-2 days ago i was idling at 34-36*C, web browsing and watching HuluHD vids at 37-39*C and gaming(Left 4 Dead 2) at 41-43*C.
Today i am idling at 48-50*C, Web/HuluHD at 51-53*C and L4D2 at 53*-57*C
I looked into it and found a lot on Cool n' Quiet, so i disabled it, didn't seem to do anything but I did notice regulation of my Clocking based on load i needed to application.
It about an hour ago just bailed out and i saw a message flash for about 1 sec, most i caught was "Processor unit can not function properly shuttign down" or along those lines. Prior i saw no temp spike or Core use spikes. I was literally watching PArks and Recreation and CPU-Z then it happened.
At some points in L4D2, i was hitting high temp and 89% CPU use...that seemed uncommon to me.
I am not incompetent when it comes to thing like this, i have patience, so i began to search the forums here and elsewhere. I could come up with solutions but none fit my case.
I tried to check for a BIOS update but to no avail(through software from Gigabyte) then on the site. Should i go from my current F5 BIOS to F12(flashing it)?

Moments before posting this i restored my system to about a week ago, i know it won't do the BIOS, i just wanted to to clear my head and get rid of the new ATI software so it removed the "OCing" of my processor option.

Any ideas on where to go from here?

Side note: The idle temps have been on the good side even in an 80*F room. I had the AC on all day and at 72*F, then had a fan blowing too the PC and still can get below 47*C in good moments.
Attached is pics from CPU-Z from 11:33pm Central(Chicago) Time.
Does this seem to look right? I know the voltage looks fine(1.35v)
http://imageshack.us/photo/my-images/577/help1c.jpg/

EDIT: CPU cooler is aftermarket, not much better, copper piping and is a bit bigger than stock. I'm all air, rear 120mm, front 90mm. I have one of those duct/tube things to help direct air from the side of the case in tot he CPU, thats the area the fan was kind of aimed towards.
 
i skimmed through it since its 12:30 AM here

but sounds like AOD jacked up your voltage, and enabled CNQ .... try uninstalling AOD and see if the issue corrects itself, otherwise, jump into the BIOS and say set to default, that should put you to where you were (AOD shouldn't change your BIOS settings, but i've seen weirder shit happen with automated OC stuff)
 
I uninstalled and then system restored to a week ago(pre Download of any new software) I set BIOS to default, didn't work, so i did the battery removal method to reset it. All voltage looks the same in BIOS as CPU-Z. 1.35v core.
If it doesn't crash again let's say, those temps seem a bit high still don't they?
Thank you for your time too, i hadn't expected anythign this late.
 
what is the exact cpu cooler you are using?

those temps seem perfectly fine for the stock cooler,since you said the one you have is not much better than stock,you should not expect much more.

go into the bios and enable Cool and quiet,im thinking it was enabled the whole time and that you just noticed it from amd overdrive,CnQ will drop your temps dramatically,since it will clock your proc to deal with different loads,keeping the temps down.disabling it runs your proc at full speed all the time and will increase heat quite a bit.

Also while in the bios look to see if your cpu fan speed is set to auto or set at a manual percentage.

*edit* when did you build this system,its possible you messed up your processor drivers when you restored,long shot,but you never know.go into your device manager and see if there are any yellow "!" next to anything.
 
I will do as you said again, i understand that CnQ will drop me to 800Mhz when under no load or not needed as well as the fan, i may have just had a massive lapse in memory.(not sarcasim) I will say though, earlier i had CnQ on, and it seemed like when i need the higher MHz to kick in, it was and it it was boosting the fan but I still never saw it drop below the 46-47*. Ill report back momentarily.
 
the cpu fan is probably scaling with the cpu speed,set it to 100% and see if the temps drop with with the lower speed from CnQ,also,spray out your heatsink,I have to even remove the fan and get the build up out every now and again cause its quite dusty here and spraying it does not always remove everything.

what heatsink are you using exactly?
 
I am not sure the exact model as it was given to me last summer and i do not have the box anymore. It looks very similar to this, but a bit thicker. I know this is an Intel model too.
http://www.compusa.com/applications/SearchTools/item-details.asp?EdpNo=6624654&CatId=493

I restarted and set CnQ on, the temps are hovering around 37-40* C with a room temp of 74*F. I am literally in the room with the thermostat about 10 ft x 10 ft.

I think you're right, i think AOD must have adjusted somethings and now they are all back in order. I plan to get a can or air tomorrow as well, i would have today but issues arose late. I may have just worried about nothing.

This is my CPU/heatsink/fan, best i could do in moments notice.
http://imageshack.us/photo/my-images/696/0000002d.jpg/

thanks for all the help too.


EDIT: After restart, CPU fan disabled: running at 100% all the time, around 37*C-40*C with CnQ. While opening iTunes, Steam(logging in), Mozilla opening to come here.
I'll clean it tomorrow and go from there.
 
Last edited:
That is one of the stock coolers,the fan on it has a built in temp sensor,it samples the air and adjust the cpu speed accordingly,kinda sucks cause you can not adjust the fan speed manually at all.(well I could not on this GD-70)

glad to hear you got it all sorted,also,that heatsink will get dirty fast,take off the fan every once and a while and clean under it,just be careful not to break the little plastic tabs that hold the fan on.
 
Last edited:
Back
Top