Need a new cooler case for FX60?????

Pops

n00b
Joined
Apr 2, 2007
Messages
20
Ever since I installed my FX60 I cannot get my PC to run while gaming due to hot CPU. I have a Zalman 9500 AM2 with AS5 installed correct.

Once I start gaming the FX gets to hot to run.

I can remove the front cover of my Lian Li PC-65 and the filter and the PC is cool and runs great. It idles at 41c MB and 42c CPU. The CPU under load will set off the Asus Probe2 at 65c if I don't have the front off the case.

Have I reached the limit my case can handle?(see sig.)

I am thinking of changing the case to the PC-60 Plus 2 W. With the 120mm fan in front and one blowing out of the case over the Video Cards maybe I can keep the FX cool.(Ambient 72f)

Could there be any other reasons why the FX is getting so hot?

TIA,
Pops
 
Make sure your entire case has good airflow so the hot air doesn't get trapped inside.
 
Do you have the cpu overclocked at all? The 9500 might not be up to the task of cooling such a hot running dual core. Just noticed you have a pair of 7800gtx. Those cards are also known to add tons of heat to the mix.
 
No overclocking or increased voltages.

The case is stock:
2x80mm in front
1x80mm Top
1x80 rear

So the FX60 runs Hot by standards?

TIA,
Pops
 
What is the vcore defaulting to 1.30 or 1.35? I know that not all fx60's default to the same vcore. The ones that default to 1.35 run a little hotter usually. If you haven't manually set vcore in bios, it might be a good idea to do so.
 
The FX is a ADAFX60DAA6CD. The specs at AMD list variable 1.3-1.35.

I'll check the Bios and set to 1.35. Asus Probe II is showing 1.39.

Thanks,
Pops
 
Maybe I should ask in the Case Forum for help too.

If a Moderator reads this post would it be OK to post in the Case Forum also with my question?

TIA,
Pops
 
I have it set to 1.3 in Bios and Asus probe says it is 1.33.

Is Asus probe accurate? The MB Temps are hot too.

Tried playing Fear Combat with case closed up and MB alarm went off too. That is set at 55c.

Thanks,
Pops
 
I'd really like to see a picture of the inside of the case, becuase these temps seem to be out of control.
 
BIOS: 1303 being used shows Voltage set to 1.285

Hardware Monitor in BIOS shows 1.33

Asus Probe II shows 1.33

Should I keep dropping voltage until the Hardware Monitor and Asus probe read 1.3??

Why do I get differant readings?

Anyone using this MB and which BIOS are you running? Maybe a differant BIOS will have a lower temp reading.

I have a digital camera now but am unsure how to post pictures here. Some help with this please.

TIA,
Pops
 
BIOS: 1303 being used shows Voltage set to 1.285

Hardware Monitor in BIOS shows 1.33

Asus Probe II shows 1.33

Should I keep dropping voltage until the Hardware Monitor and Asus probe read 1.3??

Why do I get differant readings?

Anyone using this MB and which BIOS are you running? Maybe a differant BIOS will have a lower temp reading.

I have a digital camera now but am unsure how to post pictures here. Some help with this please.

TIA,
Pops

Go download Core Temp and see what your actual temps are, Asus probe can be off by a degree or 2 and usually will report higher voltage (the only way to know the real voltage would be to read with a multimeter but its a PITA to do). Case in point i have my cpu set to 1.36 and will report at 1.41 with asus probe.

At stock those are some high temps! I've heard that the 9500 isn't always up to the task, might wanna look into a new HSF like AC Freezer64.

I have specs near yours and my x2 4200+ @ 2.64 loads around 42-44c and idles around 32-34c (side door off will be 26-29c) This is with a gigabyte G-power lite btw. Even with a FX60 you should see temps close to mine but a touch hotter with any decent cooler, what kind of thermal compound did you add and did you apply it correctly?

Your bios is fine, its the latest official bios from ASUS.
 
I used AS5 and applied just a rice size drop as the web page directs. Even gave the cooler a twist after install.

I'll take a look at that cooler.

I put a 120mm fan from Lian Li that pulls the hot air off the video cards and blows it at the vents in the rear of the case. I also removed one 3.5 bay cover to allow the fans to pull in more cool air.

This allowed me to play Fear Combat with video options maxed out at 1600x1200 and no alarms!!

The temps were still a little high but I guess I am on the right track.

Thanks for all help! Please keep it coming.

Pops
 
Checked out Core Temp.

Here are the readings:
core #0= 35c
core #1= 35c

vid= 1.275v

Big differance from Asus Probe
CPU= 43c
Vcore= 1.33v

So am I correct if I assume my FX is not running as hot as I thought? Can I except the Core Temp readings over the Bios and Asus probe?

Being new to this I am just confussed how I get so many differant readings.

TIA,
Pops
 
Core Temp crashes my PC!
Checked web page and in the Debug the problem is known. So I removed it.

Pops
 
I modded the case with a second 80mm under the original. Now the Zalman is blowing more air right into the fan for exhaust.

Bought a 120mm fan oem from Lian Li (BS-01) that pulls air off the video cards and blows out the back stock vents.

Opened up the air intake in front of case where the 2x80mm sit.

My temps are down to:
38c-cpu
43c-mb
at idle

My cpu never goes over 51c and the MB hits about 51 also under full load.
I'm happy with this. I can play games again.

I would have stayed with my 4000 if I had thought going to the FX would have been this much trouble.

Thanks for the help!!
Pops
 
Back
Top